Having problems with your Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum ?

The suction isn't working. It is there, but wehn

\015 The suction isn't working. It is there, but wehn you put it together it won't vacum.\015

Answers :

Check hose to see if it is clogged. ALSO MAKE SURE ALL THE COMPARTMENTS ARE PUT BACK CORRECTLY.If the water resevoir isn't sitting correctly , you will lose suction. Check that hoses are corect as well.
Repair Help & Product Troubleshooting for Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

It has no suction. It was fine yesterday. I washed the dirt container and the filter, let it dry and put it back in the vacuum. Today my vacuum isnt picking up any dirt and has no suction. When I took the hose out of the back, it started blowing dust and dirt out but still no suction.


Look for a place where the vacuum line has to turn in a near 90 degree turn. It's easy for it to get stopped up there. ... Vacuums

My eureka optima upright bagless vaccum has VERY low suction using the floor part. the hose has excellent suction. i removed the little translucent door underneath and there were no blockages, i cleaned the brushroll thoroughly and that hasnt helped either. i know this probably isnt recommended but i turned it on to the floor setting with the brushroll off and stuck my fingers up the intake as far as i could, the suction was good further up but it just seems to stop down at the base. because i s


I will try and help here. Is the sole plate on the bottom of the vacuum complety on and there are no visible cracks along the seam where it meets the body? This is the usual cause for this. Onc you take of the plate to access the roller and brushes, ... Eureka 431A Optima Bagless Upright Vacuum

No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.


Generally, the problem is that the belt is not running the brushes.  This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed.  This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The suction isnt working


Probably is full or could possibly be clogged ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The suction isn't working. It is there, but wehn


Check hose to see if it is clogged. ALSO MAKE SURE ALL THE COMPARTMENTS ARE PUT BACK CORRECTLY.If the water resevoir isn't sitting correctly , you will lose suction. Check that hoses are corect as well. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Suction from hose isnt strong enough. Vacuum


There is probably a clog on the U channel (little Gray tube that attaches to the Vac tubing). Pull it loose and look in side all the tubing. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Ive got a dc07 dyson just changed the belt on it as i had to since then it isnt picking anything up at all nothings clogged up had it to bits and put it all back together again properly. The hose is working when i take it off its got plenty suction but when i run it along the floor it picks absolutely nothing up any ideas that i havent thought off. Thanks


Sounds like the hose underneath has become detached. Have a look and if its not that come back to me. Also can yo9u check your U Bend is still on as these can come off. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a DC14. About a wk ago it was making loud sound and bar stopped turning. i unclogged everything....now the suction works great. However, the bar still wont turn. The belt inside is still intact and isnt loose. Several solutions suggested resetting the "Red" button...i have searched the vacuum over and over. there is NO red or any other color reset button. The bar is set down perfectly in there, the cover plate is installed properly. What other problems could there be? Or do i just need to


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The suction isnt working - Panasonic MC-V5005 Bagged Upright Vacuum


Disconnect the hose where it goes into the base and see if you have suction there.if you don't then your intake hose is clogged.thats the hose that your long stretch hose connects to.take a coat hanger and bend the tip so the end is rounded.work it d ... Panasonic MC-V5005 Bagged Upright Vacuum

My electrolux ZTI7671 turbo nozzle has stopped working, nothing is stuck but the turbine has become very stiff and isnt rotating with the force of the suction. what shall i do?


... Electrolux Vacuums

My bissell powersteamer isnt suctioning the water


Please try the following suggestions to see if you can get your machine suctioning properly:\012 \0121) Remove the Tank-in-Tank Assembly and place your hand over the motor intake valve. This valve is located next to the Floor Noz ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

LOSING SUCTION IT APPEARS WHEN IN UPRIGHT POSITION, ALTHOUGH SUCKING (TO SOME DEGREE) IT THROWS BACK SMALL PIECES TO THE BACK OF THE VACUUM OPNTO THE CARPET BEHIND, AND THE CONTAINER HOLDING THE STUFF ISNT WHIRLING AROUND THE CONTAINER. I WONDER IF THE PASSAGE TO THE WIND TUNNEL IS BLOCKED, AND OF COURSE THAT IS THE PART I CANNOT GET TO, AS IT NEEDS A SPECIAL TOOL TO UNSCREW THE BACK OF THE VACUUM.


Is brushes moving, if so it is clogged , usually takes a star bit to take apart to clean ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Loss of suction on a canister bagless. What is the best way to ensure there are no blockages - i have checked but can't be sure there isnt a blockage in the hose somewhere.


Take a coat hangar (one of those nasty metal ones) straighten it out as long as you can get it and slowly slide into hose, twisting it as you go. You can also tap hose when doing this to loosen anything jammed in there. ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

I have a dyson dc17 animal upright and I feel that the suction isnt as strong as it use to be . Is there something that I can check to be sure it is operating normally?


Check , replace filters, empty jug, If still poor , you may have a partial blockage somewhere,pete ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My electrolux ZTI7671 turbo nozzle has stopped working, nothing is stuck but the turbine has become very stiff and isnt rotating with the force of the suction. what shall i do?


... Electrolux Vacuums

Why isnt the turbo head brush spinning


Hi there,I'm sorry to hear you're having difficulties with your Dyson. As you haven't stated which model of Dyson you own, I can't provide specific advice. If you can reply and let me know which model you have, I should be able to help. ... Dyson Vacuums

Dyson suction loss


Make sure the filters in the bottom are clean, then remove the canister and you will need to clean it thouroughly, pay close attention to the upper section inside where the "cones" come togetheri have read that they are prone to clog up here and lose ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Suction Cover The suction cover of my Eureka Deep Steam 2575A is broken - the tabs snapped off of the cover so I am unable to screw the suction cover back on. I need to purchase a new suction cover but can't find one anywhere. Anyone know what I can do? thanks


The exact same thing happened to me. i just called and ordered it from eureka. the number is 1-800-282-2886. the cover cost 13.07 and the s ... Eureka 2576A Steam Vacuum

No Suction I get great suction in the hose, but when I plug the hose back into the unit, there is no suction and the air flow indicator line goes completely red. I've changed the bag and filters. I took the small panel off the back and made sure there is no clog, and took the hose off to make sure there was no clog there. Still no suction. Please help.


I about to say that's always a clog of some sort that causes that ... Miele S7210 Bagged Upright Vacuum

I have a Dyson DC24/ all floors, serial number 530-US-D78353 that I have registered already w/ your company. The vacuum is generating suction from the main outlet (that goes to the canister)///but once I place the canister into position..there is no suction from the floor foot. The roller is working/spinning, but no suction..picks up nothing, I have cleaned and rechecked all filters and can not figure out why I suddenly have no suction. Appreciate your input and/or advise where there is a local


... Dyson Ball DC24 Bagless Upright Vacuum

No suction Just received my refurb. dyson animal bagless. Finally figured out how to get it all together, turned it on and there is no suction coming up thru the beater bar. The hair is just collecting around the bar and not going up into the canister. It appears all the suction is going thru the open red end of the attachment hose, which has a vented cover piece. Am I missing a piece or is there a switch to turn of the attachment suction?


So the red hose isn't connected to a part on the vaccum so like it is connected to the connester but not to an opening just above the beater bar, this is the only idea i can supply you with. good luck, maybe i got lucky and helped you out. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

No suction I just replaced the bag, and normally after this I have a lot of suction. Now that I have changed the bag I have less suction that I had before. Not even enough to picj up dog hair. I snaked he hose and checked all of the connections. It seems to have an air leak but no amount of tape will fix this. I cleaned the filer as well with warm water and dried it and re installed but still absolutely no suction. I am ready to throw it out! Any suggestions would be appreciated


1, Does the blower (discharge) side blow bunches of air??Yes: Something is clogged from the bag to the hose end. Try blowing out the hose from the discharge side.Or: The bag is not properly seated. Make sure that the plastic piece is ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Hi my dyson dc18 has great suction from wand but when you got to use the vac for floors little suction but wand still got suction even while vacuming floors is it suposed to stop suction from wand


My Dyson dc18 had the same symptoms. The wand worked well and the floor bar had no suction. After removing pieces & shoving my fingers into the machine (no blockage) I found the suction pipe rotates between two positions (floor and wand). It look ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

No suction I am getting no suction on my central vac at the vac. I do not believe that the piping is plugged up, the vacuum is not creating suction. What are the causes of no suction at the vacuum and how do I take the top half of the Nutone central vac off?


Use the guide at builtinvacuum.com/flowchrt.html to find the issue and solution. Most likely you need to test it without any filter and be sure the bottom of the unit is attached :) To get access to the motors you need to unbolt the very top sides. ... Broan-NuTone CV350 Performance Bagged Central System Vacuum

Lost suction my DCO7 lost suction in the hose I started taking it apart and cleaning it and looking for clogs (probably more than I should have) and when I put it back together it has awesome suction in the hose but no suction in the base. It just pulls the pine needles up (christmas tree) but they never appear in the "bag" compartment and when I look they are just all gathered in a clump in the bottom by the brush.


Hi.\015\012\015\012Remove the sole plate turn the 3 plastic screws to unlock & lift off.\015\012\015\012Now remove the blockages that have accumilated from the oppening of short clear hose.\015\012Check you can turn ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0544 seconds