Having problems with your Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum ?

Too much solution being dispensed--carpets very wet--running out of solution before even 1/3 of room cleaned


Answers :

The cleaning solution tank is only sufficient for part of a room, unless the room is very small.
\015\012
\015\012Are you following the instructions for using the cleaner carefully? The machine has to be pulled backwards (towards you) at a steady pace in order for the vacuum to pick up the water that is dispensed. Do not use it like a normal vacuum cleaner - that will not work.
\015\012
\015\012You need to start facing a wall, and pull the cleaner towards you, moving at about one foot every two or three seconds. The vacuum will then pick up the water that has been dispensed and the carpet will be damp but not sodden.
Repair Help & Product Troubleshooting for Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Too much solution being dispensed--carpets very wet--running out of solution before even 1/3 of room cleaned


The cleaning solution tank is only sufficient for part of a room, unless the room is very small.\015\012\015\012Are you following the instructions for using the cleaner carefully? The machine has to be pulled backwards (towards you) at a ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Cleaning solution continually runs from clean solution tank


Where is the water running out? If at the bottom of the tank, is the seal on where the tank sits on, Maybe the rod inside the handle is staying pushed down, the reservior asm is bad, or a water line is off.\015\012\015\012 ... Hoover F5881-900 Vacuum

I have a Model F7431-900 and is a SteamVac V2. When I press the trigger for water or cleaning solution, the water just runs right through it even after releasing the trigger. What kind of problem do I have? Is it most likely a valve problem? I'm handy at fixing things and want to avoid the large repair bill if I take it in.


This sounds like a stuck solenoid. The Dual V models use solenoids to contol soap and water flow to the floor, along with a pump unit. If your unit is 12 months or less it is under warranty. I am not sure about the cost of the solenoid. ... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum

FILLING INSTRUCTIONS. I HAVE A BISSELL PROHEAT PLUS 12 AMP CLEANER. HAVE LOST MY MANUAL. NEED INFO ON FILLING THE MACHINE. DO I MIX THE BISSELL CLEANING SOLUTION WITH THE WATER? IS THERE A SEPERATE PLACE TO PUT THE CLEANING SOLUTION, IF SO HOW MUCH SOLUTION PER WATER CONTENT. THANKS


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Same problem as voirjs 12/29/09 - runs a while & needs brushes cleaned w/same repeat scenario. have been doing all of the cleaning as felix80 said on 1/8/10; but it still continues the run awhile & need cleaning behavior. a more indepth solution is required.


I called iRobot Customer Support, and they are sending me a new cleaning head module. ... iRobot Roomba 560 Robotic Vacuum

We have a Hover F7411-900 which runs great but for some reason the wash does not dispense the cleaning solution. It works fine on rinse but not on wash. We tried cleaning the round piece at the base of the cleaning solution but that did not fix the problem. How can you repair so that the wash will work.


That would be the wash silonod, the thing that makes the soap and water mix together in order to make the soap come out at the bottom were the brushes are. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Cleaning solution does not come out of the rotating cleaning head or the hand-held nozzle the solution pump seems ok but does not run (electrical continuity check between the two leads on the pump show very low resistance so they seem to be intact) - no dirt or blockage is apparent (it is a very simple device with 1 moving part wires to the pump also pass a continuity check THERE IS NO VOLTAGE on the pump leads from the control circuit board when I turn on the "manual" cleaning mode - a


You can contact Bissell directly at the following\015\012\015\012For UK inquiries:\015\012Monday - Thursday 9 am — 5 pm\015\012Friday 9 am — 4 pm\015\012\015\012BISSELL Homecare (Overseas) Inc ... Bissell SpotBot Robotic Wet/Dry Vacuum

My irobot scooba does not spray cleaning solution out after about the first 30 seconds it is running. I have tried all the suggestions in this post with the suction bulb to charge with air, and then with water to clean it out. water does come out of both valves when forced with the bulb or immediately after using the bulb to charge it. then after it runs for about 30 seconds the floor is dry.


... iRobot 5800 Scooba Vacuum

I was vacuuming my room and all of a sudden I hear this loud noise, then notice the roller brush isn't spinning. Thinking too much hair was caught I separated it from the rod and hose to clean it out, but noticed that the roller brush didn't move at all while I was cleaning it. I've cleaned the brush before and it would roll around with little effort, but this time I couldn't move it at all. After removing hair and string I put the vacuum back together and started it up, but the noise continued,


It sounds like if the rod is clean then there is debree inside the roller where the rod fits in too. ... Hoover Platinum Cyclonic Bagless Canister Vacuum With Power Nozzle

Brushes only work when Dust Bin is removed!! I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'


HI, If the brushes work , without the bin, the problem , the problem could be caused , due the failure at the bin lock mechanism. There is a sensor that checks if the BIN is connected properly or not. This problem is best resolved by getting ... iRobot Roomba 560 Robotic Vacuum

I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'd stop here first before calling again! Than


Ok, this is a "Brush Height Adjustment" issue. It will probably work great on a hard surface but on carpet the brushes bog. If you've taken the unit apart already...Sorry....do it again. When you do, you'll see a String which allows the brushes to " ... iRobot Roomba 560 Robotic Vacuum

Picture you sent for me is not the same model as I have mine is a dual vac v carpet cleaner with the solution tank on the side of clean water tank so I need to know how much solution to put in solution resevoir.


The solution tank injects the cleaner depending on the selection you have make such as light or heavy. You fill the tank with cleaning solution. ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

I have a roomba 551. Have cleaned and removed every bit of dirt and hair off it bu the brush cage won't close when the larger bush is put in. The cage will only click locked on one side, and the other side keeps hitting the brush and won't close. It's almost as if the bursh itself is not even, but this doesn't seem to be the case either. I've even tried removing the yellow rings, but makes no difference. Occasionally it runs fine, but most of the time the roomba just hobbles and clacks as i


Hi, had the same problem, it was like the main brush no longer fit into it's slot, so the brush cage would not latch. I discovered that the yellow bearing tip on the main brush twists off, and inside I found a lot of hair twisted around the pin. Th ... Vacuums

I bought a roomba pro elite robotic floorvac at a tag sale from an elderly couple who apparently used this vac very little as it was very clean and she had never even used it enough to use the extra filters that came with it, she said it was just too much for her to bend down to work it or move it. i suspect she stored it but kept the battery in it. after charging it, it powers up and sings a little tune, but then shuts off. i cleaned everything, including the sensors. it still shuts off, do you


... Roomba Pro Elite Bagless Robotic Vacuum

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.


... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

I have a Royal 7910 extractor and even though I vacuum before cleaning the carpet, by black cocker spaniel's hair gets pulled into the plastic pick-up attachment and I cannot find an easy way to clean it out. I have tried taking the screws out to separate the halves, but it seems as though they might be glues together. I have run water from a sink sprayer though the openings with some degree of success, but it still is pretty cruddy. I have tried snaking pipe smokers pipe cleaners up the pick


One person wrote this in a review:\015\012Most home carpet extractors are very difficult to take apart for cleaning and maintenance. The Royal 7910 is the exception. No tools are needed to take the front housing off to clean out all the pet hai ... Royal CE7910 Wet/Dry Vacuum

I used my Hoover FloorMate, SpinScrub Hard Floor Cleaner for the first time today. My intent was to clean the grout in my kitchen/family room floor. Since the water was dirty I know it cleaned the grout but I was only so-so pleased with the results. Any hints? What about the grout solution? Do you mean I can only use the Hoover product?


The Hoover model 800 has seperate brush assembly to do grout. The 500 model (yours) has only the one hight brushes so other means must be taken to do grout. I have a 500 and all tile floors and I'm bumbed too.\015\012\015\012Kirk Thompson ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

I have a Bissell Proheat 2x Model 9200. The solution goes directly through to the carpet. The tank empties extremely fast even when I am not pushing the button. I have also noticed that I have soap spots on the carpet when pushing the cleaner forward. These spots are not even associated with the cleaning mechanism. I have inspected the cap on the tank, but it seems to be OK. Any suggestions?


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell 9200 Upright Vacuum

Bissell ProHeat uses way too much solution. It will empty the solution container in just a few minutes - and that's not even on the heavy traffic setting.


The valve asm. at the bottom of the solution tank may need to be replaced. ... Bissell Vacuums

Bissell 1698-1 Solution applicator indicator (red spinner) does not rotate and no solution is being applied even though both the water and cleaning sol'n tanks are full and properly nested.


The heater is blocked wih lime scale ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

My bissell proheat cleaner is letting out little spray solution when on the floor cleaner setting. If I press the sprayer on the attachment solution comes out of it even when it is not set on the attachment setting what should I do to fix i. How do I clean the water nozzles under the machine?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Bissell Proheat Turbo 2x model 9300. It has stopped spraying at the floor. The hand tools will work so I assume this means the problem is at the base somewhere. I cleaned the nozzles but don't know what to try next. It has always had a problem with dumping too much cleaning solution as well, don't know if this is a contributing factor


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My dyson DC16 constantly shuts off even when battery is fully charged. I cleaned the filters to see if that was the problem. It only runs for a few seconds before it shuts off. It will run intermittently for about 10 minutes before dying completely. Please advise


Hi its Darran at Dyson. From your description of the problem, it sounds as though there is a problem with the battery. Your DC16 will have been supplied with a 2 year guarantee. If it still within this period, please contact ... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

I have had my Bissell 6591-X for 2 years. I hate it! No matter what I do all the fuzz, hair, whatever fills up around the upper filter before it even starts to deposit in the cup. It has done this ever since I bought it. No matter how much I take it apart, clean it, clean filters, empty the cup, nothing does any good. I spill more dirt onto the vacuum and floor than ever gets in the cup. I will never buy another Bissell.


Sure your not over filling it ? ... Bissell Vacuums

I have a Thane h2o mop ultra, I added some bleach to the water tank to clean better, the unit worked for a while, enough to clean 1 room, then even if the tank is still full of water the steam is not


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0515 seconds