Having problems with your Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum ?

My bissell will not suction water from the carpet

\015 My bissell will not suction water from the carpet\015

Answers :

Please check the following:\012


First check the motor duct gasket. The motor duct gasket is visible once the tank is removed. It is located underneath the handle on the top of the base of the machine. It has a black rubber coating around it. If there is no suction there please let us know. If your machine does have suction at the duct, continue to check the following:


- Ensure the Ready Tools Dial is set to the appropriate setting (Floor Cleaning or Hose Attachments).
- Remove the tank from the machine and ensure the tank lid is attached properly. The front window must first hook onto the lip of the bottom of the tank and then drape over the tank. Latch the bottom tank to the top tank lid. THIS LID CANNOT BE ATTACHED PROPERLY IF THE TANK IS NOT REMOVED FROM THE MACHINE.
- Make sure the Water Tank is not full on the outside of the bladder. If it is, empty the tank.
- Ensure the hose is firmly attached to the back of the machine. If not, re-insert as necessary by twisting into place.
- The machine must be in an upright, locked position and set to the Hose Attachment setting. If the handle is slightly tilted back while using, it will create a small gap at the suction inlet (where handle meets gasket, above the Bottom Tank) which will cause little or no suction.
- Check the red Tank Lint Screen for debris. If the Lint Screen is dirty, the unit will have poor suction. Clean the Lint Screen if necessary.
- If the float flap door in the tank lid is activating prematurely when you turn the machine on, this flap door should be replaced. This tank may need to be emptied.
- Check the Tank Lid and Tank for damage.


If you continue to experience low suction, please contact BISSELL Consumer Services at...

Mon-Fri: 8am to 10pm ET
Sat: 9am to 8pm ET

Repair Help & Product Troubleshooting for Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet

Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn't blocked as well. ... Vacuums

Water is not being discharged. I have filled the reservoir that holds the carpet cleaner fluid And I have filled the water container. I know how to use the cleaner, it has always worked, But now, no water is being discharged to the carpet. I turn it on, squeeze the trigger, but nothing comes out. The wheel that is suppose to spin (to indicate that water is being discharged) is not spinning. Everything else works. I.e. the suction works, and the hand held accessories work.

That means that the pump belt is worn and it needs to be replaced. You can get a replacement belt and view the manual here:Bissell Pump ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Suction problem my proheat wont suction water out of carpet,,, it made a mess of my carpets now, any one no how to fix the suction problem?

The valve on the bottom of the water bucket is not being pushed up enough to allow the vaccuum to go through. Perhaps a part is missing but I used a small ball bearing and a car vaccuum cap to build it up and now our works but it is still a piece of ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum


Make sure the lower tank lid is on securely, clean the intake filter on the top right of the machine. ensure the front panel is installed (the square to remove for hoe use). this has to be in place for carpet operation ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My hoover steamvac powermax is releasing the water to clean the carpet but there's no suction power so the water is remaining in my carpet

... Hoover F6213-900 SteamVac Agility TurboPOWER Steam Vacuum Vacuum

Suction Problem I just borrowed the Hoover Steam Vac Deluxe w/ 5 brush agitator from my neighbor and it worked ok for the first few minutes, although the suction would stop and go. When I had enough water to dump I did it and when I put it back on it no longer sucked the water up from the carpet. She admits to having it for 15 years, but why did it have to break on me. Makes me look as though I did it!

Check and make sure the dirt water tank is properly on if it it is chech inside the lide to make sure the red stopper is not stuck to the top this will cut off the suction ... Hoover F7431-900 SteamVac Vacuum

The suction on my Hoover Spin Scrub 50 is suddenly not working. This is the 2nd or 3rd time I've used it and until now it has done a great job. But now it leaves my carpets soaking wet with no hope of drying and no dirty water is being suctioned into the dirty water tank. Help!

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Poor suction...continued Wow, thanks for answering so quickly! To answer your question, yes, there is suction at the screen, but it is very weak. I keep that screen clean. As a side note, I noticed that when I remove the top clear plastic cover (that would be part # 37 on the diagram, as far as I can tell) there is decent suction coming from the intake there--part 36? 30? it's hard to tell. But with the cover on, I feel no suction (from where it sucks up the water directly from the carpet),

Wish I had it in my shop, it is hard to figure your problem. I do know that you must have something out of place and you may have to take it apart to find it. You may feel some suction there at the top of the clear nozzle, but maybe it isn't strong ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

Suction button Although my Hoover Spin scrub is working perfecting dispensing the solution, when I go to suck up the solution from the carpet--I am having problems with the RED suction button that keeps popping up. I have to stop the cleaner and lift up the dirty water container to break the suction. Ive tried cleaning the netting that is encased around it, but still no luck. Any help would be appreciated! Thanks

This happens when the filter on the inside of the lid for the dirty water tank is pushed all of the way up. You need to leave a 1/4 in. gap from the top to the top of the filter ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a 9300-1 bissell carpet cleaner and when i used it today the vacuum was not sucking the water up. i know its working because when i take the water tank off i can feel the suction from the valve that connects to the water tank. any suggestions...

... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

No suction to retrieve water from carpet

The tank lid of your recovery tank is designed to engage two tabs to lock the front of the lid down on the seals. Look at the front corners of your recovery tank. You will see a tab extending out on each corner. These two tabs insert into the corresp ... Vacuums

My bissell will not suction water from the carpet

Please check the following:\012 \012First check the motor duct gasket. The motor duct gasket is visible once the tank is removed. It is located underneath the handle on the top of the base of the machine. It has a black rubber coating aro ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

No suction of the water from carpet after soap is applied

Hello :1: A vacuum pulls air through the bag, then through the tube attachment and\015\012 then through the base (with the spinning agitator brush).2:Check for signs of suction. Remove the tube attachment from its cradle \015\ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a new STEAM VAC Dual V All Terrain Carpet and Hardwood Cleaner. I have used it once and it worked well. Now, the second time, I have no water return. I checked the tank location, the brushes are moving slowly (but the plastic surrounding around the brushes moves as well ??) Water is coming out. There is hot air blowing out, but there is no air suction. What is wrong? Ursula Litzcke

Hello litzcke.\015\012There are lots of people facing this problem as well as other problems with this machine. As there are lots of faulty with this product; would not **** up water/air/shampoo, will not brush and lots more. If it is under war ... Vacuums

I have the Hoover max Extract 77 and when I'm cleaning the carpet, the clean water tank leaks on the floor, even if I'm not squeezing the trigger. The clean tank doesn't leak when I fill it, but once I place it where it fits and start using the vacuum, the clean water drains out on the floor. The dirty tank fills up, so the suction works, but, I don't know what is going on?

... Hoover Vacuums

When button is pressed, water does not come out of the holding canister. still seems to have suction, but water doesn't come out to rinse/clean carpet.

Please check the following with liquid in both tanks.\012 \012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\012- Check for debris o ... Bissell 9200 Upright Vacuum

No suction suction gate open. not pull water out of carpet

... Bissell Lift-Off Deep Cleaner 94Y2

I am having those same problems , brushes are not agitating . leaking water from the bottom of the unit , the suction is week it is not pulling the water out of the carpet .

... Eureka Atlantis 2595A Upright Wet/Dry Vacuum

When cleaning carpet, I heard a single pop sound, and the suction of the water from the carpet stopped. The brushes are still spinning. Can you help?

I think there is some thing in ur machine, , may be there is some dust or metal piece, , , jst open it nd clean it, , , then try again ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

The manual for my hover steamvac was lost I would like to clean my carpet but the vacum will not suction up the water from my carpet the model is F5915-900 series 1120

You can download the manual here. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Little green machine pro heat pet the collection tank wasn't collection and dirty water was coming out of the bottom. i took it apart, cleaned it up and put a new "duckbill" gasket in. then it quit spraying, but i think i got that working again. now after i spray and get a good foam on the carpet, i switch to suction and it seems very weak. i can see the water moving (trickling) from the head into the hose but it is not reaching the collection tank -- actually, i am not sure where its goin


My machine wont pick up the dirty water. If I take the cover off the recovery tank there is a lot of suction but it wont **** up the water. my carpet is soaked. What can I do

At power head clean out area before power head also look for small hose and clean out and look at rollers,i hope this works if you have directions still they should be able to help you out some more.thanks ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My bissell carpet cleaner will not suck up the water. There is suction but the water is not being sucked up

What could be the problem ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Using a dirt devil platinum carpet cleaner - no suction - dirty water still on carpet. Everything else works fine.

... Dirt Devil M091400 Platinum Force Wet/Dry Vacuum

My Bissell Proheat 8920 carpet cleaner does not suction water

Its pluged check the hose that goes to the tank ill bet it hasnt ben rinsed the dirt sets in the hose and dries and it gets like concreet but this will solve the proublam ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 1.2053 seconds