Having problems with your Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum ?

No suction of the water from carpet after soap is applied

\015 I am getting no suction of the water from the carpet, after the shampoo is applied-why?\015\012also the rotating brushes only work intermitently in the upright position (not attachments)\015

Answers :

Hello :

1: A vacuum pulls air through the bag, then through the tube attachment and\015\012 then through the base (with the spinning agitator brush).

2:Check for signs of suction. Remove the tube attachment from its cradle \015\012and, after turning on the vacuum, put your hand to the end of the tube. \015\012Is there any suction at all? If there is a little bit of suction then \015\012you may have a clogged air tube.

3:Check the vacuum bag. It may be very full. If it is then remove the bag \015\012and replace it with a new bag. Check the suction power again. Has the \015\012suction improved?

4:Check the tube attachment. Completely remove it from the vacuum. You \015\012usually have to twist and pull the tube attachment out of place at the \015\012point where it connects to the back of the vacuum. Check the suction \015\012power again. This time you place your hand on the vacuum right where the\015\012 tube used to come out of the back of the vacuum. Has the suction \015\012improved?

5:If the suction power has improved then you probably have a clogged tube.\015\012 Dog hair, people hair, leaves and more can get lodged in the tube \015\012slowly over time and then suddenly block the tube completely.

6:Clean the tube by first trying to shake the debris out of the tube. If \015\012this does not work then go outside and run a hose through the tube. Use a\015\012 pressure nozzle if you have one. Run the hose through one end of the \015\012tube. Then run it through the other end. Repeat until the debris is \015\012disloged. Dry the tube and then reattach to the vacuum.

7:Has suction power improved or returned to normal power? If yes then you \015\012can stop reading now. If not then read on.

8:Check the air hose in the base of the vacuum. This hose is usually \015\012pretty short and you can see if there is any blockage. If you see \015\012blockage then try to remove it. You may need to reach into the hose with\015\012 a tool (like a screw driver or something long).

9:Has suction power improved or returned to normal power? If yes then you \015\012can stop reading now. If not then read on.

10:If you made it to this step then you may have a problem with the motor \015\012on your vacuum. If this is the case then you will need to take the \015\012vacuum in to a repair shop.

Things you will need :
1 Philips screw driver
1 flat head screw driver

Warning :

# Always unplug electrical devices before you work on them.

# Never work on electrical devices around water or when you are wet.

I hope this will help .

please rate !

Repair Help & Product Troubleshooting for Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No suction of the water from carpet after soap is applied

Hello :1: A vacuum pulls air through the bag, then through the tube attachment and\015\012 then through the base (with the spinning agitator brush).2:Check for signs of suction. Remove the tube attachment from its cradle \015\ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Doesn't apply water and soap to carpet . . . seems to be plugged. . . water tank never empties, soap remains in dispenser bottle

You will need to srip it down to unclog the pipe work they do get blocked up with soap ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

We just took our dirt devil Platinum Force Carpet Shampooer Model CE7900 out of the box - first time used. It puts soap and water down fine, but we can't get any dirty water picked up. None of the trouble shooting suggestions in the manual apply. HELP! (We had only the power on when trying to pick up the dirty water.)

... Dirt Devil Easy Steamer Upright Wet/Dry Vacuum

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet

Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn't blocked as well. ... Vacuums

Hoover SteamVac Plus 1200 upright hot water extractor Water/carpet cleaner applying o.k. Suction on the "floor" does not work. Suction on the hand tool works somewhat, but water is not collecting in the bucket. There is suction coming from the floor but water is not going into the bucket. It does not appear to be clogged because I can feel with my hand that air is flowing from the floor. The water is not being sucked into the bucket.

... Hoover Vacuums

Water is not being discharged. I have filled the reservoir that holds the carpet cleaner fluid And I have filled the water container. I know how to use the cleaner, it has always worked, But now, no water is being discharged to the carpet. I turn it on, squeeze the trigger, but nothing comes out. The wheel that is suppose to spin (to indicate that water is being discharged) is not spinning. Everything else works. I.e. the suction works, and the hand held accessories work.

That means that the pump belt is worn and it needs to be replaced. You can get a replacement belt and view the manual here:Bissell Pump ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Suction problem my proheat wont suction water out of carpet,,, it made a mess of my carpets now, any one no how to fix the suction problem?

The valve on the bottom of the water bucket is not being pushed up enough to allow the vaccuum to go through. Perhaps a part is missing but I used a small ball bearing and a car vaccuum cap to build it up and now our works but it is still a piece of ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum


Make sure the lower tank lid is on securely, clean the intake filter on the top right of the machine. ensure the front panel is installed (the square to remove for hoe use). this has to be in place for carpet operation ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Suction Problem I just borrowed the Hoover Steam Vac Deluxe w/ 5 brush agitator from my neighbor and it worked ok for the first few minutes, although the suction would stop and go. When I had enough water to dump I did it and when I put it back on it no longer sucked the water up from the carpet. She admits to having it for 15 years, but why did it have to break on me. Makes me look as though I did it!

Check and make sure the dirt water tank is properly on if it it is chech inside the lide to make sure the red stopper is not stuck to the top this will cut off the suction ... Hoover F7431-900 SteamVac Vacuum

Have a bissell pro steam cleaner the suction is great but the water leaks out the bottom I think it should spray from the front and the soap cleaner won't dispense from the bottle so I have to mix the soap cleaner in with the water Any solutions

Use this guide!\015\012http://newzealand.bissell.com/images/IncludeContent/Service_Center_Help ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My hoover steamvac powermax is releasing the water to clean the carpet but there's no suction power so the water is remaining in my carpet

... Hoover F6213-900 SteamVac Agility TurboPOWER Steam Vacuum Vacuum

Is this free? i have a bissell carpet cleaner and i cannot get the soap and water to come out. it will **** up the dirty water however. i just found the belt is broken but i can see no way of how to put a new one in. is a broken belt the reason no soap is coming out?

If it is the flat belt that broke, that is the pump belt, the pump can't work without it. To replace the belts, turn the unit over, remove the red holder, has one screw, pull it out, then the brush roll will come loose. You can replace the belts th ... Bissell Powersteamer 1694 Upright Vacuum

The suction on my Hoover Spin Scrub 50 is suddenly not working. This is the 2nd or 3rd time I've used it and until now it has done a great job. But now it leaves my carpets soaking wet with no hope of drying and no dirty water is being suctioned into the dirty water tank. Help!

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The hoover steam vac 5 brush agitator dispenses water and soap but does not show any return water to dirty water reservoir. The carpet seems damp but not soaked, still a bit troubling no waste water...what up ?

You do not have the needed vacuum on the dirty water intake. Possible causes are:\015\0121. No adapter sleeve in the back of the dirty water tank (the one that you remove to put the fabric hose adapter in)\015\0122. The dirty water top i ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Poor suction...continued Wow, thanks for answering so quickly! To answer your question, yes, there is suction at the screen, but it is very weak. I keep that screen clean. As a side note, I noticed that when I remove the top clear plastic cover (that would be part # 37 on the diagram, as far as I can tell) there is decent suction coming from the intake there--part 36? 30? it's hard to tell. But with the cover on, I feel no suction (from where it sucks up the water directly from the carpet),

Wish I had it in my shop, it is hard to figure your problem. I do know that you must have something out of place and you may have to take it apart to find it. You may feel some suction there at the top of the clear nozzle, but maybe it isn't strong ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

Suction button Although my Hoover Spin scrub is working perfecting dispensing the solution, when I go to suck up the solution from the carpet--I am having problems with the RED suction button that keeps popping up. I have to stop the cleaner and lift up the dirty water container to break the suction. Ive tried cleaning the netting that is encased around it, but still no luck. Any help would be appreciated! Thanks

This happens when the filter on the inside of the lid for the dirty water tank is pushed all of the way up. You need to leave a 1/4 in. gap from the top to the top of the filter ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a 9300-1 bissell carpet cleaner and when i used it today the vacuum was not sucking the water up. i know its working because when i take the water tank off i can feel the suction from the valve that connects to the water tank. any suggestions...

... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

No suction to retrieve water from carpet

The tank lid of your recovery tank is designed to engage two tabs to lock the front of the lid down on the seals. Look at the front corners of your recovery tank. You will see a tab extending out on each corner. These two tabs insert into the corresp ... Vacuums

My bissell will not suction water from the carpet

Please check the following:\012 \012First check the motor duct gasket. The motor duct gasket is visible once the tank is removed. It is located underneath the handle on the top of the base of the machine. It has a black rubber coating aro ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My bissell carpet cleaner will not suck up the water. There is suction but the water is not being sucked up

What could be the problem ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I have the Bissell heat pro 2x 8920 and the water doesn't come out. The soap just mixes with water tank and the carpet stays dry

Check to ensure there is liquid in the water tank and the formula bottle.\015\012\015\012Note: This machine will spray with liquid in the Water tank only if the machine is set to the Water Rinse setting. On any other setting, you need to ... Bissell 8920 ProHeat 2XTM Upright Vacuum

Little green machine pro heat pet the collection tank wasn't collection and dirty water was coming out of the bottom. i took it apart, cleaned it up and put a new "duckbill" gasket in. then it quit spraying, but i think i got that working again. now after i spray and get a good foam on the carpet, i switch to suction and it seems very weak. i can see the water moving (trickling) from the head into the hose but it is not reaching the collection tank -- actually, i am not sure where its goin


I have a new STEAM VAC Dual V All Terrain Carpet and Hardwood Cleaner. I have used it once and it worked well. Now, the second time, I have no water return. I checked the tank location, the brushes are moving slowly (but the plastic surrounding around the brushes moves as well ??) Water is coming out. There is hot air blowing out, but there is no air suction. What is wrong? Ursula Litzcke

Hello litzcke.\015\012There are lots of people facing this problem as well as other problems with this machine. As there are lots of faulty with this product; would not **** up water/air/shampoo, will not brush and lots more. If it is under war ... Vacuums

My machine wont pick up the dirty water. If I take the cover off the recovery tank there is a lot of suction but it wont **** up the water. my carpet is soaked. What can I do

At power head clean out area before power head also look for small hose and clean out and look at rollers,i hope this works if you have directions still they should be able to help you out some more.thanks ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Water and cleaner not coming out, The machine is only 6m old and was working fine, I have cleaned every where I can to see if there was a blockage but nothing is working. The heater is working, there is a suction but the water and soap will not realease when triger is pulled. it will not work on on the tool spay.

Check the complede length of the hose. You may find a crimp in the most inconvenient place. You say you cleaned everything ... can you blow through the hose where the cleaner comes out? (don't drink anything!) ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0663 seconds