Having problems with your Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum ?

My Bissell Pro Heat Select 2X does not pull up the dirt from the carpet into the water. The water just slowly disappears. The first time I used it the water got really dirty. The very next time I used it it worked differently and the water just disappeared until it was all gone. I've only used it a couple times and I don't see where it is working. Has anyone else had this problem?


Answers :

Inside the plastic suction lid is a little red plastic filter that has to be cleaned out every time you use it because it sounds like your vaccum is not picking up all the hair and debri before you clean the carpet causing the water to be injected into the carpet and disappearing and not filling the tank with dirty water. Steve
I agree thank you SO much!! I have been so frustrated- even on the phone with customer service without any solutions from them. I was ready to throw it in the garbage. Thank you!!!
Repair Help & Product Troubleshooting for Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Bissell Pro Heat Select 2X does not pull up the dirt from the carpet into the water. The water just slowly disappears. The first time I used it the water got really dirty. The very next time I used it it worked differently and the water just disappeared until it was all gone. I've only used it a couple times and I don't see where it is working. Has anyone else had this problem?


Inside the plastic suction lid is a little red plastic filter that has to be cleaned out every time you use it because it sounds like your vaccum is not picking up all the hair and debri before you clean the carpet causing the water to be injected in ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

We have bissell pro heat and I have put new belts on and took off the top plastic cover I blew out the lines and I still can't get it to pump water or solution. The red little spinner flow indicater does'nt get water, if I pour water into it it runs out the front. I guess I don't know what else to do. The machine worked fine the last time we used it about 6 months ago. Any suggesttions?


Did you check and make sure the belt is still on right? They do come off from time to time.There are like 6 long screws holding the top cover to the bottom. The are real pain in the behind to put back together once you take them off. T ... Bissell Vacuums

Our SteamVac will not release cleaner and water. Everything else appears to be okay. After last use it was rinsed out and left for two weeks at which time it would not work. I would like to obtain a repair manual to study and be able to disassemble it properly. Thanks in advance, William Ferguson E-mail: [email protected]


Click this link directly\015\012http://www.sacreativeservices.com/forum_stuff/steam_vac/\015\012\015\012 ... Vacuums

My Tim Horton's (Bunn) Coffee Maker won't stop boiling the water really hard (to the point where it practically boils the full pot away). When I go to make coffee the next time it's boiled so hard that it doesn't give me a whole pot of coffee just like 3/4 of a pot, and if I haven't used it in like a day it's boiled it down to half a pot??... it's beginning to make me angry, as I have cleaned it in the past for this trouble, but it doesn't help or make a difference. Can somebody please help me??


... Vacuums

How do you clean the inner mechanisms of the steamer. I tried the instructions in the manual which basically said to put fresh water in a few different times to remove the scales. Can I use a vinegar


... Rowenta IS9100 Steam Cleaner

It will no longer vacuum up the water, Ive only used it 3 times! We unpluged it and let it set we even cleaned it out....


Hello..Try This: Remove the recovery (dirty water) tank, and then remove the lid. Now reinstall the lid (there are two tabs on the front of the tank, the lid must be installed over those two tabs, and then "rolled" trowards the back., It will "cli ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Bissell Proheat Turbo puts out too much water and cleaner and won't **** it back up like it should. Also when I use the attachments dirty water runs out the the hose when I am done. It's used a lot, I shampoo all the carpets about 2 times a month and I shampoo the funiture 1 time a month. I bought it about 3 months ago.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have Bex Bissell Proheat. It is one problem requiring fixing each time I use it. Just had a new pump fitted as water not spraying out. Now the water is not being sucked up. For the money this has not been a good product. When it works it is good. But the constant issues each time it is used is frustrating.


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Just bought and used the Hoover MaxExtract 77. First time the water was extracted from the carpet. Second time NO water in tank. Now I have wet carpet. I've taken the machine apart 3 times and cleaned the filters and still the water is not extracted from the carpet.


... Hoover F6055-900 SteamVac Maxextract LS Wet/Dry Vacuum

We have a Bissell Proheat Cleanshot 2X Model 9500 Steam carpet cleaner. The first time we used it things were great. The second time we used it it left tracks in the carpet. We have no idea what caused this. We tried using the machine on an entirely different carpet and it did the same thing. After vacuuming the carpet about 10 or 12 times, the tracks are still embedded in the carpet - HELP!!!! We're read and reread the manual and contacted customer service and received no help.


First things first. It's only the second time you have used the machine, so it must be fairly new. If you have a receipt and the unit is less than a year old you should take it to an authorized Bissell repair center and have the machine inspected und ... Vacuums

I have a hoover 3000 i have not used in awhile, and since I removed a large rug, I would like to use it again on my slate floor. HOWEVER, I cannot get it to pick up ANY water in the water recovery unit......it is dry, dry, dry. I have put in a new filter, cleaned the nozzle unit, the scrubber , and reconnected both the recovery unit and the water unit several times, but to no avail. I would like to get a graut attachment a well as replacement part, but since I can't get the basic unit to work, I


Have you made sure the plastic filter cover with the round hole in it that covers the filter is in place ( part # 59177096 ). This piece seems to get lost, and without it there is no pick-up. The other common problem is that the wheel assembly has be ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Need instructions how to use Hoover Steam Vac Spin Scrub. I borrowed it from my Sister and she left it with no instruction book or letting me know how to operate it. I put water & cleaner in top tank. That's all I know to do. Do I put any water in bottom tank? I figured not, since that is probably where the water goes when sucked up by vac. Do I leave lid on bottom tank? I usually use a commercial cleaner, and this is very different. I need to know NOW, as I must return it to her today, and I'm


I did have a solution in just a few minutes. Someone responded with a solution that gave me the website where I could go and print the manual in pdf, so did that, and checking instructions I was able to clean my carpets and get the shampooer back to ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I was cleaning my carpet using my hoover steamvac ls. I had already changed the water 3 times. The last time, the water ran out and I kept running it for a couple of minutes trying to **** up some of the water off the carpet when it just shut down. I check the breaker and the outlet and they were OK. Checked my manual for troubleshooting; couldn't find an answer there. Do you think I burned the motor up (I didn't smell anything) or will I have to send it in for repair? When I clicked on your web


(1) take the tank off and reassemble to assure you sealed to the lower handle.\015\012(2) the water feed has nothing to do with the motor or electrical, purely mechanical.\015\012Hoover web site is free, no cost. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

We have a series 90S, 2.5 gallon Shop Vac. We used it for the first time to try and **** up water in the basement. Each time we turned it on, it would shut down after collecting less than 1" of water. We had to remove and squeeze out the foam sleeve each time, before it would work again (nowhere near 2.5 gallons!). Any ideas? Is the plastic sleeve that can move up and down inside, the float (poorest manual I've ever seen!)? Should there be a ball float that we're missing? Thanks for any s


Remove the foam sleeve when using the unit to pick up water.\015\012The float is in there to indicate when the unit has "enough" water in it. The float rises with the amount of water and when the water reaches a certain height the float is "pulled" ... Shop Vac Vacuums

No manual Hi there my bissell will not **** up the water its been some time ago that I used it and it has not been used more than 2or 3 times can any one help me with this. I have also miss placed my manual and instruction this does not help me either .So if any one can help Id be a happy woman with clean floors thanx Vickie


Link to the manual download - http://www.bissell.com/Product_Search.aspx?Criteria=1699\015\012CHeck to see if the front of the unit is clogge ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have an euro-pro steam cleaner model # sc505 that is about 2 years old. It has only been used a limited number of times, about 3 or 4 times. It now has a tightly sealed safety cap on it and it will not release allowing me to add water to the steamer to use it now. Any tips on fixing it? I'd love to have a products guide to items that are available for compatiability with our sharkie. We constantly see new items available and wonder will that product work with ours?? Thanks!


... Euro-Pro Shark SC-505 Handheld Steam Vacuum

Used the Bissell Pro-dry 7350. Turned it off emptied dirty water and re-filled hot water & cleaning solution. Wouldn't turn back on. Have only used 3 times.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Shampooer instructions..... I have a Kirby Generation 3 with the shampooer. it has been awhile since i have used it and i sort of remember how to attach it but i was wondering this vacuum has a tray and i assume it is for sucking up the dirty water but when i went to use it no dirty water was going into the tray.....help what did i do wrong......thank you for your time...............spanny


Try this link....http://reviews.ebay.com/KIRBY-CARPET-SHAMPOOER-INSTRUCTIONS-MANUAL-DIRECTI ... Kirby Generation 3 Bagged Upright Vacuum

I'm using a steam vac for the first time, i wanted to know if the bottom piece that you empty out the dirty water has to have water in to use it. or is it suppose to be empty?it's an upright hoover steamvac for heavy traffic areas and spot cleaning


Hello,\012The bottom piece should be empty when you use your machine. Make sure you rinse it our real good when you are finished.I hope this helps. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

While using, steam stopped coming out in force at the port levels in the head. Suddenly started high pitch whining, pressed button just above connection site and end flew off with great force pouring water onto floor and carpet. Unplugged immediately for safety and unable to get it to deliver steam force again. Less than one year old and used only 8-10 times only in walk areas where there is no carpet with distilled water. Please, advise, cannot find booklet. Thanks So Much, Beverly Crumme


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it may not be getting steam to the head...Euro ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I just bought a shop vac to **** up the winter slop in the garage. the first time I used it, it worked perfectly but the 2nd and 3rd times I used it, it spits water from the exhaust. Why? It doesn't seem to have a plug/clog and I have the foam sleeve plus the circular paper filter on it, as per directions. Help!


Too much water in the unit causes what you describe. Water should be drained and the unit completely dried between water events, or unit will rust and have shortened life. ... Shop Vac 925-13 Canister Wet/Dry Vacuum

I have a bissell quickwash 1950-e. I bought it Jan. 2006, and have only used it 8-10 times, I live in a very hard water area, so I though if I put some vinegar in with the cleaning solution it would get rid of any hard water deposits, unfortunatly the solution went lumpy in the tank and stoped spraying out water, I have opened it, hose clean, sprayer not blocked, x at bottom of water container when depresed water trickles out, component that opens the x when water container placed, also ran wate


Hard to say what is causing your problem, replacing the cap and insert on the water tank may help, part #2041111, even tho it may trickle out water when depressed, they can still be bad. The other thing would be the rod not relesing the water like i ... Vacuums

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet


Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn't blocked as well. ... Vacuums

Hello i can turn my steam buddy platinum 44G258 on, water boils, press hand gun get a buzzing noise like you do with a jet wash, but no steam comes out, it seams the water is not coming through, have check the cap on water container thats ok, its where it releases the water to is seams to be where the problem is, i think ! first time we have tried to use it many thanks steve.


... Vacuums

Water is not being discharged. I have filled the reservoir that holds the carpet cleaner fluid And I have filled the water container. I know how to use the cleaner, it has always worked, But now, no water is being discharged to the carpet. I turn it on, squeeze the trigger, but nothing comes out. The wheel that is suppose to spin (to indicate that water is being discharged) is not spinning. Everything else works. I.e. the suction works, and the hand held accessories work.


That means that the pump belt is worn and it needs to be replaced. You can get a replacement belt and view the manual here:Bissell Pump ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0872 seconds