Having problems with your Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum ?

I have a Bissell Proheat 2x cleaner which has worked perfectly on every occasion. Today I filled the machine as usual with water and formula and switched on, the motor ran, the lights were on and the brushes rotated but upon pressing the spray trigger no water or formula was released. I have cleaned the jets underneath and also followed instructions to release any airlock. It still wont release the water/formula. What else can I do? Thanks Charles


Answers :

Please check the following with liquid in both tanks.
\015\012


\015\012

- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.
\015\012

- Check for debris on spray tips. Clean them with a soft brush (on old tooth brush works well). The spray tips may be lifted out for easier access.
\015\012

- Ensure the tank lid is properly attached to the bottom of the tank. To attach this properly, remove the Water Tank from the machine. Hook the front window onto the lip of the bottom container and then allow the window with lid to cover the complete tank. Secure the latch on the back of the bottom tank to the back of the tank lid. THE TANK LID CANNOT BE ATTACHED PROPERLY IF THE BOTTOM TANK IS ALREADY INSTALLED IN THE MACHINE.
- Check the bottom of the Water Tank and the Formula Tank to make sure each has a red auto-load gasket attached. Make sure the Water Tank and the Formula Tank are seated properly. Depress the x on this gasket to ensure this depresses and release back out. Liquid from the tank should dispense.
\015\012

- Remove the handle completely and re-attach. Once the handle is re-attached, re-attempt to spray.
\015\012


\015\012

If the machine continues to not spray, check the following:
\015\012


REMOVE THE COLLECTION TANK:
\342\200\242 Make sure the unit is set to water rinse
\342\200\242 Remove the smart mix bottle and fill it with water only
\342\200\242 Place the smart mix bottle into the collection tank reservoir
\342\200\242 Run the unit and try to spray. If the machine sprays, you will be able to see the water level decreasing in the smart mix bottle and you will need to replace the bottom tank. It is possibly warped.
\015\012

If these suggestions do not resolve the issue contact BISSELL Consumer Services.
\015\012

1-800-237-7691
Mon-Fri: 8am to 10pm ET
Sat: 9am to 8pm ET
\015\012

Repair Help & Product Troubleshooting for Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Bissell Proheat 2x cleaner which has worked perfectly on every occasion. Today I filled the machine as usual with water and formula and switched on, the motor ran, the lights were on and the brushes rotated but upon pressing the spray trigger no water or formula was released. I have cleaned the jets underneath and also followed instructions to release any airlock. It still wont release the water/formula. What else can I do? Thanks Charles


Please check the following with liquid in both tanks.\015\012 \015\012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\015\012- ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell Powerease Lighweight Deep Cleaner. (Shampooer) After I fill the solution tank with the solution and water, I put it in it's slot, but all of the contents just come flowing out. I have only used this machine twice and it worked ok. You are supposed to press the trigger and the solution sprays out and then release the trigger when you want it to stop. But like I said, now I just put the tank on and all the contents come flowing out. I don't know what's wrong or how to stop it.


... Vacuums

I have a Model F7431-900 and is a SteamVac V2. When I press the trigger for water or cleaning solution, the water just runs right through it even after releasing the trigger. What kind of problem do I have? Is it most likely a valve problem? I'm handy at fixing things and want to avoid the large repair bill if I take it in.


This sounds like a stuck solenoid. The Dual V models use solenoids to contol soap and water flow to the floor, along with a pump unit. If your unit is 12 months or less it is under warranty. I am not sure about the cost of the solenoid. ... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum

Hello i can turn my steam buddy platinum 44G258 on, water boils, press hand gun get a buzzing noise like you do with a jet wash, but no steam comes out, it seams the water is not coming through, have check the cap on water container thats ok, its where it releases the water to is seams to be where the problem is, i think ! first time we have tried to use it many thanks steve.


... Vacuums

I have a bissell proheat complete 2x. When I press the trigger to spray the water, it sprays for a couple of seconds and then the pressure drops and stops spraying. I turn turn it off for about a minute, turn it back on and does the same thing again. Jose Cortez


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Bissell ProHeat Upright Carpet Cleaner will not spray water or solution. I have filled the bladder; I have filled the formula tank; I have reseated the tank; and I have turned the unit off and then on again to reprime the trigger. Nothing has worked. Any suggestions?


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Just got a bissell proheat clearview force cleaner, we press the trigger, no water sucking action or shampoo release going on .. what's wrong?


By the Floor Cleaning setting knob and Tools for PreHeat setting knob, there's a red x inside a clear circle cap. Is it spinning at all? If not...twist the cap off and remove the red x. Under the red x there is a tiny little filter. This might be plu ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

My karcher puzzi carpet cleaner has just stopped working, when I press the trigger the water does not spray through


... Vacuums

The water and soap dispenser spray continuously, even after releasing the trigger. How can I repair that?


This is a sticky trigger mechanism. You should simply disassemble, clean and re-assemble.\015\012\015\012Thanks for using FixYA!!\015\012 ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Trigger on hose attachment not working so water sprays constantly


From your description, the trigger sounds like it is stuck in the release position. this sounds like a very simple repair. The component parts need to be looked at by a service shop ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Won't spray wate rwhen you press trigger.


What if the brush spins just fine? Answer that one Vac Belts. ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

My shark super steamer model SC710L heats the water but the stream trigger when pressed there is no steam


... Euro-Pro Shark SC710L Handheld Steam Cleaner

We have a Bissell Proheat 2X (model 8920). The problem we are having is when water/soap is initially released (all settings) it continues to leak out the front water spray nozzles unit the water containers are empty. The vacuum works but can't keep up with the continuous water leaking out. Do you have any idea what is sticking open to allow the continued release of water when the machine is running? Thanks Rick


Return it. It is faulty and should not do that. Mine does not. Does require changing water about evrery 10 minutes but one can see the filth in the water. Also re-clean with plain water over areas that were cleaned to remove all cleaner. Old cleaner ... Bissell 8920 ProHeat 2XTM Upright Vacuum

The trigger for water spray is not working


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Bissell proheat My Bissell won't dispense cleaning formula but it sprays water and sucks up the water. The attachments spray water but not the soap also. how to fix?


First is the smart mix valve turning like it should? If it is then replace the soap dispensor. Also is the gasket on the valve at the bottom of the bottle? ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

When using the floor configuration, I can't get the trigger to cause a spray of either water or cleaner. When using the tool configuration and the hand device with brushes etc, the spray works well with the hand trigger.


The trigger on the handle for tthe floor configuration has become loose or broken. When you squeeze it, the action pulls a rod that runs down the length of the shaft and goes into the base and allows the water to spray. You need to check and make sur ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The tool attachment for the hose on my Bissell ProHeat 2X CleanShot won't spray soap or water. The bristles on the tool rotate without a problem and the suction is working fine, it just won't spray water when I pull the little gray trigger on the tool.


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a hoover power scrub steamvac, the main soap dispenser trigger on the handle click when pressed and does not work (broken spring??) the other soap triggers on the hose and the trigger on top to dispense extra water both work. Can I fix the main trigger myself?


... Vacuums

Water will not come out when i push on trigger button. So water does not come out. I have taken it apart and cleaned it. The problem seems to be in the triggerI push on the handle to release the water.


Order the part from bissel see if that fixes sound like you know what wrong just need get part number from bissell.Could be some kinda pump also thats bad not pushing out the water.I got bissle heated one black it only problem the seals r ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Model 79011 ProHeat - First the water and cleaning solution wouldn't come out without pressing the trigger several times. Now the trigger doesIs there a spring on it inside the handle or do I just need to order new trigger. I have only used the cleaner 3 times.


... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

It will empty the cleaner but will not spray water filter is clean spray heads were taken off & i could blow threw them is it a case of no prime in pump if so should i fill pump i had this thing all apart and i now know evry inch of this matchine when i pull the triger it sometimes will spray for a sec.but thats it i also took the switch out and air goes threw when i press the switch if it is the prime in the pump how can i fill the pump . what hose on the pump will prime i thankx for your advic


The problem is most likely that your pump belt is worn, stretched or broken. Here you can get the belts you need and view the manual:htt ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

My Bissell Quicksteamer Model 1960-R won't spray cleaning solution. I have cleaned it and taken apart the whole thing. I can't find any problems. The holes are not cloged where the water comes out as I disconnected it and blew through it to be sure. The lines show water trying to go through. It is as if it doesn't have enough power to pump the water out when I squeeze the trigger. I am thinking it is the pump thing but can't find a replacement part for it.


... Bissell 1960-3 QuickSteamer Plus Upright Vacuum

Water coming out w/out trigger being pressed


You may have a problem with the valve at the bottom of the tank, or a water line has come loose. How old is this, there is a 1 year warranty, so if less then a year, take it in for repair. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell 1623 keeps spraying after I release the trigger


... Bissell 1623 Powersteamer Upright Deep Carpet & Hard Floor Cleaner

Water & soap spray constantly even when trigger is not depressed.


This may be related. Mined wouldn't spray after it sat for awhile. I tore it down, tapped on the solenoids and reassembled. That worked.Its possible the solenoids may be stuck in the open position although not as probable as stuck in the ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0711 seconds