Having problems with your Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum ?
Bissell pro heat 2x brushes are not turning???
Brushes are controlled by belts. They must have come off or broke.
Repair Help & Product Troubleshooting for Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
My bissel pro heat cleane's brushes stoped. I checked the belts. They are okay. There is no sign of heat or problems around the motor. Is there a mercury switch some where in the handle so the brushes only turn when the handle is lowered?
Depending on which model you have, you did not say, if the cogged belt goes to the pump pulley, the cogs may be wore away or and won't turn the brush roll. On some other moels, there is a brush roll motor that may have gone bad. ... Vacuums
Bissell 9200 pro heat carpet cleaner , brushes won't turn, both side belts are good. bad brush motor? or brush moter belt?
... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
I have a Bissell Pro Heat 2X carpet cleaner and the brushes spin, then stop. I turn it off and when I re-start, the brushes do not spin until I push foreward. The it spins and stops again. Both belts are tight. The brushes spin if held above the carpet, but upon contact with carpet it stops. Same thing on a hard surface.
The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
My bissell pro heat carpet cleaner is not working properly...the scrubby bar is not turning... the belt is intact and working and it is turning the knob inside but the brush bar does not turn
How are the bearings? Maybe the motor that drives the belt is burnt out. ... Vacuums
Bissell pro heat 2x healthy home brushes wont turn
Hey Brenda! Here's a link to troubleshooting steps for the brushes not turning.\015\012http://www.bissell.com/FAQDetail.aspx?id=1128&cid=ccsocial ... Vacuums
I have a Bissell Pro Heat Carpet cleaner and the brushes will not turn. The pully is not turning the belt.
If the motor shaft that rotates the belt to turn the brush does`nt turn you have motor problem`s if it does you need to free up what ever is keeping the brush froom turning freely ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
I have the Bissell Pro-heat 2X which is new and only used one time and today I am trying to use it and the brushes will not work at all. They will not turn and spin like they are suppose to.....Please Help ! John Baumgartner Roanoke, VA
Look on the front of the little gree guy and where the switches are you should see a small diagram of a brush above or below one of the switches flip the switch to the brush diagram ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum
Bissell pro heat 2x brushes are not turning???
Brushes are controlled by belts. They must have come off or broke. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Bissell Pro Heat 9300 brushes won't turn before and after replacing belts
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Brush Bar not turning on a bissell pro heat 2x
Here is the Instruction or User Manual for the 9500 series machineswill give instructions how to check and change drive delts ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Bissell pro heat X2 I need the directions, I lost them. I tried to use it, the water will not come out and the brushed do not turn all the time
Follow the link below to access the User's Guide.\015\012http://www.bissell.com/searchresul ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
I have the bissell pro heat pet 2x and my brushes won't turn or operate...
Check the belt ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Bissel pro heat /brushes do not turn
Belt worn or hair build up can clog it from spinning. I've seen this on other models. Just remove the hair slowly. If the Belt is worn you can replace that from Bissel or any store that sells their product.Check to ensure that the p ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Bissell pro heat burshes will not turn
You need to replace the belt. Here is the belt you need:Bissell ProHeat Belt ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum
Bissel pro heat unit brushes will not engage
Keep in mind they only turn when the handle is down. if that is not the problem, it is usually the belt.David ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Brush not moving in Bissell pro-heat
If the belt is more then 6 months old or more, then the belt will have to be replaced reguardless of the way it lookes. belts can stretch over time and when you put the machine on the carpet the friction causes the brush to stop because the belt has ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
My Bissell Pro-Heat 2x 12 amps Model 9200-2 The rollers wont turn and the water wont release
WON'T SPRAY ??? ... Bissell 9200 Upright Vacuum
Bissell Pro Heat Powersteamer- Filed it up, turned it on, asusual, but no water flowing from machine at any setting. Vacuum part works.
The water sprayers on your Bissell are probably clogged. I had this problem this morning, myself, with my machine, about 15 months old. They get clogged up with mineral deposits. This is a *fairly* easy thing to fix yourself. Read all the way to ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Bissell Pro Heat clear view plus...Flow indicator not turning...? Plugged? how to unplug
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
Need to replace a broken brush belt on Bissell Pro Heat Model # 88910-W
Easy, unscrew the bottom plate, keep in mind that most bissell shampooers have one belt longer than the other based on the left vs right side\015\012\015\012hope this helps ... Bissell 8910 ProHeat Clear View Upright Vacuum
I have a bissell pro heat and the brushes are not rotating at all,it still sprayes water,everything else is ok.
Most likely the belt theres one on each side if not you'll need to take it in its the safety switch or lower motor ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
My bissell pro heat power brush won't spray from the floor unit
My bissell quicksteamer wont spray water ... Bissell 8910 ProHeat Clear View Upright Vacuum
No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I
Pump part number is 2107181, the diverter valve # 2136988. You can Bissell and they can tell you who may have parts near you, or you maybe able to order thru Bissell.com. Before you took it apart, were you getting water to spray out of the hose. I ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
Bissell Pro 2X. The brushes spin as soon as I turn it on but only spins for an instant then it quits spinning. The vacuum stays running. the handle is down.
It might be the drive belt slipping if the unit is off then the belt is locked onto the belt and then when the unit is switched on the belt slips and if its loose it doesnt hold the belt to the motor shaft ... Bissell 9200 Upright Vacuum
Taking the brush off the pro heat bissel?
Try changing the belts first if you buy the original belt package it comes with instructions on how to replace them, if not it probably has a clogged heater core ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum