Having problems with your Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum ?

We have everything filled and ready. The machine will turn on and the brush is rotating but no water or shampoo will come out. What do I need to do?


Answers :

Hi
\015\012
\015\012You would need to check the flow system. Please folow below procedure---
1. Remove SmartMix piston from the main housing and place SmartMix body (located
beneath the knob on the main housing, inside of the unit) so that it is 1/16" from
completely inserted.
2. Replace tanks in unit.
3. Plug unit in and turn it on.
4. Pull trigger to check spray -- making sure upper handle is firmly positioned onto the
lower handle. Water should flow through tubing from the tank to the pump and the red
float inside the pump should move up. If it doesn't, replace the pump.
5. Check the tubes for air bubbles as the unit is spraying -- bubbles indicate an air leak that
prevents pump from priming.
6. Locate the source of any air leaks and correct them, looking first at the auto load receiver
(under the tank) and the SmartMix assembly.
\015\012Hope this helps... Please post back if you need more information.
\015\012
\015\012Daniel
Repair Help & Product Troubleshooting for Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have everything filled and ready. The machine will turn on and the brush is rotating but no water or shampoo will come out. What do I need to do?


Hi\015\012\015\012You would need to check the flow system. Please folow below procedure--- 1. Remove SmartMix piston from the main housing and place SmartMix body (locatedbeneath the knob on the main housing, inside of the uni ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Water is not being discharged. I have filled the reservoir that holds the carpet cleaner fluid And I have filled the water container. I know how to use the cleaner, it has always worked, But now, no water is being discharged to the carpet. I turn it on, squeeze the trigger, but nothing comes out. The wheel that is suppose to spin (to indicate that water is being discharged) is not spinning. Everything else works. I.e. the suction works, and the hand held accessories work.


That means that the pump belt is worn and it needs to be replaced. You can get a replacement belt and view the manual here:Bissell Pump ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Water leak I just bought this steamer a few days ago, and already I am having problems, when I fill the water tank that your suppost to fill the water runs out before I even turn the machine on. I have tried using plugs to keep it from doing this just so I can shampoo my carpet, this seems to work to a point, considering the fact that there are two holes underneath close to the brushes and one just a little ways back from that location. Do you know if this is something that should have plugs or


If you just pruchased this, then it is under warranty, take it along with proof of purchase to a warranty repair shop and have them fix it. If water just runs out, then there may be a seal missing or a water line off. ... Eureka Atlantis 2595A Upright Wet/Dry Vacuum

I got my bissell for $7.50 from a thrift store, if you can believe THAT. Used it for the first time today after reading the manual online first. After filling the clean water bladder full of hot water and setting everything up the way I wanted, proceeded to turn things on and go for it. Well, the water/solution just kept coming and coming, without my finger on the trigger. Obviously something is jammed in the open position but where? The trigger moves freely.


This is the answer I got from Bissell:Please\015\012check the gasket at the bottom of the tank to ensure it is attached and\015\012not lodged in the reservoir of the machine. If this is not the problem,\015\012take the machine for i ... Bissell 8910 ProHeat Clear View Upright Vacuum

I own a Bissell Proheat Pet Model 8910. After just a few uses and changing both the brush and pump belts (trying to resolve problem) carpet doesn't get wet any longer. Carpet solution comes out normally but the water barly leaves the section of the tank I fill water into, resulting in carpet recieving to much solution and not enough water. Any advice?


... Bissell 8910 ProHeat Clear View Upright Vacuum

I want to brush the pile up on my carpet do I need a special attachment to do this??. I have shampood it and it still seems a bit flat. When I shampood no water/foam filled up in the front tray???I am sure I had attached everything correctly. The only thing I can think of is when I attach the brush and tray to the front of the machine, do I turn the handle back to the right way up, or do I leave it upside down, this is the one that picks up the belt.


Here's my online guide for using the Kirby shampooer....\015\012\015\012 ... Kirby Ultimate G Bagged Upright Vacuum

Need to replace the main belt on my Bissel 1698-P. Can't figure out how to get the belt around the brush roller. Have the top off. Cleaned the water tubes, didn't let the water come down.


Remove belt access door at left front of unit.\015\012\015\012Unplug the unit. Remove the two solution tanks.Remove spray tips from guides.Remove the brush and cog belt by removing the screw from the orange retaining collar.\015\012Remove belt ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

I have a Bissell Proheat 2x cleaner which has worked perfectly on every occasion. Today I filled the machine as usual with water and formula and switched on, the motor ran, the lights were on and the brushes rotated but upon pressing the spray trigger no water or formula was released. I have cleaned the jets underneath and also followed instructions to release any airlock. It still wont release the water/formula. What else can I do? Thanks Charles


Please check the following with liquid in both tanks.\015\012 \015\012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\015\012- ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I HAVE A BISSELL PROHEAT 2X HEALTY HOME, IT WORKED JUST FINE THE LAST TIME I PUT IT UP. YESTERDAY, I NOTICED THE FLOW GAUGE WAS NOT SPINNING, SO I CHECKED AND SURE ENOUGH NO WATER WAS COME OUT. I CHECKED AND ALL THE TUBS AND EVERYTHING ARE IN THE RIGHT PLACE AND HAVE LIQUID IN THEM. HAVE TRIED PRIMING CLEANING THE BRUSHES RUNNING HOT WATER THROUGH IT... HELP


Have you made sure that the tanks are seated properly and the red \012(or black) auto-load gaskets are in place. \012Check the bottom of the Water Tank and the Formula Bottle to make \012sure each has a red auto-load gasket attache ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

We have the water hooked up at the back of machine. there is a spout for the water to come in and fill the ice tray.but is does not. If we turn the water on it fills up the space under the ice basket. I keep getting red light and then the two smal llight one ice and one water come on. We can hear the motor trying to fill the ice try and then lights come on. Please help me this so I can use this product. It did not come with a manual.


The water inlet valve on the back of unit opens when the ice maker needs water. If the valve doesn't seal good because of sediment or wear it will continue to drip and when the water reaches the ice maker supply tube it will freeze blocking the fill ... Vacuums

I have a Hoover Platinum carpet cleaner, and it has stopped dispensing cleaning agent and water. This model has a separate tank for water and separate tank for shampoo dispensing. It also has a power hand unit that dispenses shampoo. All along the hand unit has continued to dispense shampoo. Symptom #1, the water tank seemed to be taking on shampoo, as it was getting sudsy. Symptom #2 - On wash mode, nothing would come out, on Rinse mode, sudsy water would come out. Later, symptom #3 - not


Somewhere on the outlet is a control tap thats driven by a rubber band and something is up with this control ,best advice here is put it in the boot of the car and take iot to a hoover dealer ,they will do it seconds for you ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have a bissell pro heat and the brushes are not rotating at all,it still sprayes water,everything else is ok.


Most likely the belt theres one on each side if not you'll need to take it in its the safety switch or lower motor ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

We lost our instructions to the Kirby Shampoo attachement and how to attach it to the main unit, the belt and how to use it. We need complete instructions and explanations on how to use this as we have tried and the belt does not attach to the main unit, the brush does not turn and the hops along the carpet and no water, etc. returns to the tray. Please help us with as simple and complete instructions as possible. THANK YOU VERY MUCH, LOUIE CAPLAN


First, you'll need to fill the tank with water (warm or cold). There are three fill lines on the side of the tank. Fill to the desired line and add one shampooer tank lid full of Kirby shampoo for each line of water. A full tank will require th ... Vacuums

I just purchased the hoover steam vac model F5853-900 from a garage sale and everything seems to be working well except i dont see any steam coming out from anywhere and the water in the vacuum stays cold. is there supposed to actually be a steamer inside this vacuum? if so, is there a button i need to turn on for the steamer to work? thank you so much for the help!


... Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum

Bissell pro heat X2 I need the directions, I lost them. I tried to use it, the water will not come out and the brushed do not turn all the time


Follow the link below to access the User's Guide.\015\012http://www.bissell.com/searchresul ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My electrolux epic 6500 power nozzle brush does not rotate. everything else works fine. do I need a new power nozzle/


No. If the power nozzle motor is running, then a new belt will do the trick. ... Electrolux Epic 6500 Vacuum

Hmmm Hi there, I actually had tried everything you mentioned except for the vinegar idea which I'll do when I get back up to my home in Oregon. I checked for pinches, the heater, etc. Water does NOT come out of the accessory tool and only will dispense out of the main area for a second or two..any liquid actually starts filling up the area right behind the nozzles and around the pump instead of OUT of the machine. I checked gaskets, made sure there was a tight seal, and even made sure the little


Check the nozzles to make sure they aren't clogged. Sometimes there is a problem with the flow indicator cap, maybe too tight or not tight enough. Try squeezing the trigger while turning the can one way or the other. If at a certain point it starts ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Karcher sc1402 bought july 2010 the water will not auto fill and red light keeps coming on because water not reaching tank machine works for a brief time when manually filled by unscrewing plug at top and filling it that way, once water level reduces machine wants more water and this doesn't happen i have descaled


... Karcher DE4002 Steam Vacuum

Karcher sc1402 bought july 2010 the water will not auto fill and red light keeps coming on because water not reaching tank machine works for a brief time when manually filled by unscrewing plug at top and filling it that way, once water level reduces machine wants more water and this doesn't happen i have descaled


... Karcher DE4002 Steam Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o


Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Bissell Proheat 2XTurbo carpet cleaner. No water will come out when I squeeze the trigger. I have filled the solution tank and the water tank. I read the troubleshooting in the manual and have tried turning it off for a minute and restarting and nothing. I took out both tanks and reseated them and nothing. It has sat for over a year but did not have any water in the water tank. Some solution was left in the solution tank. How can I make the water come out? HELP!


Call BISSELL Consumer Services.\015\0121-800-237-7691\015\012Mon-Fri: 8am to 10pm ET\015\012Sat: 9am to 8pm ET ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula


There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

Need to open rotating brush part of vacumm as motor functioning but roller not turning...perhaps belt broken put need to get into ..inside brush box ...Need help need instruction with diagrams Thanks for help Robert


... Panasonic MC-V9638 Bagged Canister Vacuum

I just bought kaz model K76P (M) humidifier in Kyoto. I filled it to the right water level (a bit below) and plugged it in (nothing else is plugged in at that socket). The light comes on, but the water doesn't heat up. I can't read Japanese so can't read the instruction manual but it seems a simple procedure: fill with water, set the heating thing the water, plug in. Am I missing something or is the humidifier defect?


Take it back to the shop it should work and even though its in japanese ,they will know if your doing it wrong ,but i think it may have a damaged heater or a wire off where its been in transit ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0963 seconds