Having problems with your Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum ?

My bissell proheat 2x works great except I'm not sure soap dispenser is draining. I clean a room and the soap is still at the fill line. Any tricks? Is it something I'm doing wrong. I have all the settings right


Answers :

Repair Help & Product Troubleshooting for Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My bissell proheat 2x works great except I'm not sure soap dispenser is draining. I clean a room and the soap is still at the fill line. Any tricks? Is it something I'm doing wrong. I have all the settings right


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I just bought kaz model K76P (M) humidifier in Kyoto. I filled it to the right water level (a bit below) and plugged it in (nothing else is plugged in at that socket). The light comes on, but the water doesn't heat up. I can't read Japanese so can't read the instruction manual but it seems a simple procedure: fill with water, set the heating thing the water, plug in. Am I missing something or is the humidifier defect?


Take it back to the shop it should work and even though its in japanese ,they will know if your doing it wrong ,but i think it may have a damaged heater or a wire off where its been in transit ... Vacuums

I got my bissell for $7.50 from a thrift store, if you can believe THAT. Used it for the first time today after reading the manual online first. After filling the clean water bladder full of hot water and setting everything up the way I wanted, proceeded to turn things on and go for it. Well, the water/solution just kept coming and coming, without my finger on the trigger. Obviously something is jammed in the open position but where? The trigger moves freely.


This is the answer I got from Bissell:Please\015\012check the gasket at the bottom of the tank to ensure it is attached and\015\012not lodged in the reservoir of the machine. If this is not the problem,\015\012take the machine for i ... Bissell 8910 ProHeat Clear View Upright Vacuum

My Rainbow E2 has been working great for years now, but recently it has stopped working on the vaccuuming setting, but will still run on the low speed air cleaning setting. I hope it is something as easy as replacing the switch. Would appreciate any tips to determine if that is the issue or possibly something larger. Tks in advance for the info/help.


Still need help, let me know.\012\012Thank you,\012Ralph ... Rainbow E series Canister Wet/Dry Vacuum

Craftsman compressor Hi we have a craftsman 30 gal vertical air compressor with 2 guages. we want to use to fill up the flat tire. Only the left gauge reads with pressure but the right one does not. How do we fill up the tire and get the right gauge to register? Can you help me


1 gauge will read the tank prssure. 1 gauge is for the regulated pressure to your quick disconnect. ... Porter Cable 7812 Wet/Dry Vacuum

My Oregon Scientific BAR888 has 5 windows, 1. temperature, 2. humidity, 3. mb/hPa or inHg (switch at the back), 4. bars showing pressure changes over 24 hours, and 5. time/date. Window 3 gives an option to set something between 0 and 2500. Oregon say they only have one set of instructions for the BAR888 but they do not match my instrument as there is nothing included for my window 3. Trouble is I don't know what the 0 to 2500 relates to and therefore don't know what to set it at.(My model does n


... Vacuums

It is 7:09 pm. and our Kalorik coffee maker was just delivered with a scratch on the upper right hand front...the coffee maker is the USK CKM 25282 ,metalic red...We had to wait over a week for this and I want another delivered right away and this one picked up! I'm not happy that this had a scratch on it and I called you right away, but not only is your office closed , your message machine is filled and not taking messages...This is Friday, the 7th of January and I'm not looking forward to ano


... Kalorik Vacuums

I have a bissell proheat 12 amp cleaner and the soap seems to just all come out at the same time. I fill the soap dispenser and within a minute it is empty and there is no soap coming out on the carpet. Any suggestions?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Tried to shampoo. need a picture of setting it up, please. thought I did the set up right but no water get to carpet


... Hoover Vacuums

Nothing happens on the "bare floor" setting, it does something on the carpet setting but definitely not the normal sound or suction.


The switch frequently go bad on those. p# h-59136035 ... Hoover S2220 Flair Bagless Upright Vacuum

I am trying to disassemble a electrolux 2100. I have looked at instructions given by Chemist 1961 and others. On the side, I have removed the rubber covers over the plastic rails but I can't remove the plastic rails that hold the rubber covers on. If I am right, these rails should just slide right out and the outer casing should come part.....or am I doing something wrong. I have pulled and pulled the rails and they don't budge. The rear end won't pop off. Help!


There's a tab at the back of the rail that needs to be released. Turn the vacuum on it's side, slip the tip of a standard screwdrive into the space between the rail and the back of the vacuum, and tap lightly with a hammer. Tap toward the front of ... Electrolux Lux 5500 Canister Vacuum

Not sucking up water out of carpet. Water tank filled, soap tank filled, red filter clean.


I don't know what the deal is with these but mine did the same thing had to have it serviced they didn't tell me what was wrong either. Check to make sure the connections aren't rusted underneath I think. ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Water leak I just bought this steamer a few days ago, and already I am having problems, when I fill the water tank that your suppost to fill the water runs out before I even turn the machine on. I have tried using plugs to keep it from doing this just so I can shampoo my carpet, this seems to work to a point, considering the fact that there are two holes underneath close to the brushes and one just a little ways back from that location. Do you know if this is something that should have plugs or


If you just pruchased this, then it is under warranty, take it along with proof of purchase to a warranty repair shop and have them fix it. If water just runs out, then there may be a seal missing or a water line off. ... Eureka Atlantis 2595A Upright Wet/Dry Vacuum

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a


The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Royal procision 7910 water from clean tank fills soap reservoir until it is overflowing through vent hole diluting soap completely


... Royal Vacuums

I have a cannister (Animal something...) Today, it didn't sound right - like a blockage. I took out the filter - seemed OK; I looked for a blockage - found none. I continued to vacuum, but it wasn't picking up. Then, I stopped again, and I found a blockage (cat toy mouse) right at the end of the hose (attachment end.) I cleared, and I turned back on - nothing. Completely dead. It is one year old, just about exactly. Desperate, Sharon Tracy


Hello,if your canister is completely dead, then it means its having a power problem. You need to focus your attention on that part of your canister that relates to power. Such as; power wire, if you don see any fault with the power cord, ... Dyson Vacuums

Our Proteam ProForce 1500 is 1 year old. The vacuum works (****) in the hardwood floor setting on the switch. The beater works on the other setting but it won't **** and beat at the same time. What is wrong and is it something I can fix?


It may be something to do with the actual switch on this unit. \012\012I have a feeling it may have to do with the wiring on the switch itself, perhaps one of the wires have come off or burned on the contact. \012\012Is it som ... Proteam ProForce 1500 Bagged Upright Vacuum

Carpet setting: the brush drive does not work with the carpet setting. Is there a way to remove the bottom to determine if something is caught in the system?


To determine if you have a clog, first remove the attachment hose like you were going to put an attachment on. With the vacuum in the upright position, turn the vacuum on and place your hand over the hose. Do you feel a strong suction? If not remove ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

I have a kirby G4 hoover which set on fire yesterday burning my hand and giving me a electric shock who can help me with this?The hoover is serviced regually by a kirby engenere it was done 4 week ago and didnt seem right from then.What are my customer rights on this matter


Call or go to him explaining this matter. They should inspect this again since they had done service work t your expense ... Kirby Ultimate G Bagged Upright Vacuum

Dc07 model, cannot get it to stand fully vertical upright. It is as if something is not sliding back into position right. Don't want to force it in case something breaks. The upright of the cleaner has been dropped from time to time. Any thoughts on sorting it out?. Thanks a lot. M


Hi, Try this quick repair and see if this fixes your Dyson in terms of not going in the upright position: This is a frequent problem that we see come in on Dysons. If this doesn't fix it, please feel free to just use the clarification req ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The soap dispenser on my 2X is not dispensing. I wrote with this initial problem and received a reply. We did everything recommended to find a clog. To begin with, we poked holes thru the little holes on the underside with a toothpick. Next we took the machine all apart as directed and cleaned out anything that had accumulated (such as pet hair). Eventually we emptied out the soap dispenser, filled it with a hot salt water solution and let it sit for 10 min. I ran three tanks of hot water


Hello,The solution to your problem is already solved, since your soap dispenser is still under warrant,What i will suggest is that you contact the company that supply you this product and explain everything to them, it is most ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a White Model 258SM sewing machine and when I have all the settings set for straight stitching, the needle bar still moves side to side. Is there something that I am doing wrong or is this normal and I just don't remember it happening before? Thank you for your assistance. If repair is needed, can you recommend someone in the Brainerd, MN area?


... Vacuums

The right front wheel came off my G6 Kirby vacuum, then the entire axle and wheel adjustment came loose--including a spring that was attached to something.


Thank heavens for a husband who can fix anything--and save me a lot of money for repairs and advice! ... Kirby Vacuums

Steam cleaner im using my cleaner have it all working but it just seems like its not cleaning right!!! i went over it for about 20 min and it has only cleaned a little of the stain am i doing something wrong or does it just take a very long time to clean!!


If it is spraying ok and the brushes are turning, then maybe the cleaner isn't strong enough for the typa of stain you are trying to clean. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Hoover Windtunnel Hello! I had to change the flat belt on my vaccum and now the belt won't stay on. I can replace it, use the vaccum, then the next time the belt comes off. Is there something I did not do right? Thanks for your help! Jennfer


Your belt may be twisted inside-out. Be sure the printed marks on the belt face away from the pulleys and shaft. The printing should face you. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0413 seconds