Having problems with your Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum ?

My brushes aren't moving when the vacuum is on.

Answers :

The belt is probably worn or broken have to replace the belt.
Repair Help & Product Troubleshooting for Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I was vacuuming my room and all of a sudden I hear this loud noise, then notice the roller brush isn't spinning. Thinking too much hair was caught I separated it from the rod and hose to clean it out, but noticed that the roller brush didn't move at all while I was cleaning it. I've cleaned the brush before and it would roll around with little effort, but this time I couldn't move it at all. After removing hair and string I put the vacuum back together and started it up, but the noise continued,

It sounds like if the rod is clean then there is debree inside the roller where the rod fits in too. ... Hoover Platinum Cyclonic Bagless Canister Vacuum With Power Nozzle

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi

Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

I have a model 116.35922 beltless drive vacuum. The agitator brush will not turn with the vacuum running and the handle down. The brush turns by hand and the reset button has not popped. Ther is nothing wrapped around the brush, but it does feel to have some resistance when moving by hand.

Wich bags for vacuum cleaner kenmore model 116.35922 ... Kenmore Vacuums

My Rainbow SE vacuum was working fine until I ran over the edge of a rug and it went in to the nozzle. I immediately switched the vacuum off and proceeded to move the rug. When I tried to turn the Rainbow back on the brush was no longer spinning. I've tried the reset button and checking the nozzle for any debris, there are none. The brush just won't spin.

Hello lilbutmunch1,\015\012The brush is motor/belt driven so you probably either broke the belt or it shifted off the motor or brush shaft. I suggest you unplug it,flip it over and look for screws that hold the baseplate together.. remove those ... Rainbow E series Canister Wet/Dry Vacuum

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn

Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc

... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Why won't brushes move on Commercial Carpet Pro Vacuum Cleaner

Luvumuch48tj: Unplug the vacuum and lay it upside down on some newspaper. Remove the sole plate (bottom plate) with a screwdriver. Pull straight up on the brushes (called a beater bar) and remove the beater bar and belt. Remove the end ca ... Carpet Pro CPU-2T Commercial Upright Vacuum Cleaner CPU2T With On-Board Attachments

The brush roller on my vacuum will not move. I've cleaned it, checked the belt, but when I put the roller back it, it will not move...almost like it is in a locked position. Everything has been done correctly from the book yet, it still does not move. Any help PLEASE?

... Electrolux EL8502 Versatility Bagless Upright Vacuum

My simplicity 7 series vacuum belt turns the agitator (beater brush) turns freely by hand when the vacuum is unplugged or off but when I turn the vacuum on the agitator does not spin even though the belt is moving. Could there be a worn out part at the agitator pin where it connects to the flywheel that the belt is connected to?

... Vacuums

The roller brush is not moving the vacuum has suction it's just the roller is not moving. The belt is not broke i can see it is still intact. I was sweeping and i noticed it just stopped moving.

... Dyson DC28 Animal Bagless Upright Vacuum

Hi I have a dirt devil vision. Hose works, but does not vacuuming the floor. Belts are not broken. Larger belt is moving, smaller belt that moves the brushes does not.

Hi krueger, sorry for the problems but hers an idea how about turning on the vacuum and put your hand under the part where it sucks uo the dirt off the floor and i guessing you would have a little suction, since the brushes are not moving its going t ... Dirt Devil M086700 Vision Bagless Upright Vacuum

We have a Bissell Revolution Lift-Off Turbo 3760-1 and the upright brush is not working/rolling. It only moves when pushing the vacuum. We checked the belt and it seems to be fine. The vacuum works fine as a hand-held. Any suggestions? Thanks!

These belts need to be changed every 6 months regardless of the way they look. ... Vacuums

Brushes don't move. vacuum motor works - Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

The brushes on the roller are driven by a wide, short rubber belt. These belts get old, worn, overheated, and break periodically.It should be a fairly simple matter to unscrew & remove the plate, revealing the belt and roller assembly. Yo ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Less than 1 year old Bissell Healthy Home 15 in. 12 amp. Brush shuts off when it is not suppose to if you move handle up and down while in vacuuming mode it engages then disengages. Dosen't matter what height brush is set at.

That machine is made to do that, there is a safety switch in the base of the machine that shuts the brush off when the handle is in the upright position. ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

I just purchased a Dirt Devil machine on Monday, I finally got it put together today and the brushes are not moving, dust is swirling around but no brush movement, I have changed all the nap settings, nothing, I am having company tomorrow and I threw my other vacuum cleaner away, HELP ME. Thank you.

Sounds like you may not have the belt attached or it is broke. ... Dirt Devil Vacuums

DC14 Dyson vacuum, not vacuuming carpets, beater brush not moving but belt is intact

Possible bad roller or bad clutch assy ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

The air hose for the vacuum is working fine but the main vacuum is not getting any suction and the brush roller is not moving.

You have a clog between the hose connector and the roller brush ... Eureka Capture Upright Vacuum Vacuum

Lg luv3008 vacuum cleaner when I move the machine, the brush roller does not rotate

... LG Vacuums

Dyson dc 17 vacuum. brush not moving

The cog belt is probably not aligned with the motor gear. Watch this video and follow its instructions closely. \012\012 ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hoover Savvy Brush only runs when the vacuum is moved backwards

Replacing the entire upper handle assembly with OEM Part #48663238 will solve your issues, for a cost of about $35 plus shipping. ... Hoover U8185-900 Upright Vacuum

I have an Electrolux EL 6988 type E Oxygan Bagged Canister vacuum brush roller in not working. I took off the stuff that was stopping to rooler from working and now I can't get the roller to move.

... Electrolux EL7024A Oxygen3 Bagged Canister Vacuum

I replaced the clutch in the dyson dc14. it isnt making that terrible noise anymore....thank god!! but the roller brush is not moving when the vacuum is in use. whats wrong?

The "horrible noise" you were hearing before wasn't the clutch! It was the roller brush. If the brush is not turning, all you are doing is burning out your new clutch. Reasons for the brush not turning: there is hair, carpet fiber or other matter wra ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

The brushes are moving but I am not getting suction through the hoses to pickup debris The model is 3575 Bissell Clearview Bagless Vacuum. I have already cleaned the filter inside

Clean every filter u can find, and check for suction in the hose ... Bissell 35755 CleanView Bagless Upright Vacuum

Belt broke 7/9/10 and we replaced it; brushes still don't move and vacuum is smoking really smells. What did we do wrong or what should we do now? This is a Powerforce Bissell.

Need replaced Brush part no: 2031196 and Belt\015\012part no :2031093\015\012\015\012 ... Bissell 6594 PowerForce Bagless Upright Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the

Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0787 seconds