Having problems with your Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum ?

My bissell 9400 pro heat steam cleaners sprayers are clogged again...how can I fix this with out taking it to a shop to get fixed?

\015 I have taken my bissell 9400 proheat steam cleaner to get the lines unclogged 3 times already....i will use it once and they are clogged again....i am looking for how to repair this by myself instead of taking it to the shop (now that the warranty is expired).......The sprayers on both the underneath and the hose are not working....please help me\015

Answers :

The water sprayers on your Bissell are probably clogged. I had this problem this morning, myself, with my machine, about 15 months old. They get clogged up with mineral deposits. This is a *fairly* easy thing to fix yourself. Read all the way to the end before trying this fix.
\015\012Unplug the Bissell. Remove the water container pieces from the top of the base. You'll probably reveal two red plastic pieces mounted in the Bissell's base, about .75" x .75". These spray water on your brushes when you press the water-and-soap trigger at the top of the Bissell's handle. These water sprayers tend to clog. See the metal spring running up the hose, behind each red water sprayer? As you squeeze the red plastic sides of one red water sprayer, use a screwdriver or other tool under the spring to wedge up the hose, to release the sprayer from its mount in the base. Stick a finger in the hole of the base of the Bissell where the sprayer was mounted and run it around the edges there including on the underside of the base to clean out any gunk you can find. Clean any gunk you can off the red water sprayer with an old toothbrush.
\015\012Now you need to remove the water sprayer from the hose. You need a pair of pliers. Use the pliers to squeeze the brass colored clip that is keeping the red water sprayed mounted to the end of the small hose there. Move the clip down the hose so it compresses the spring and is no longer on the red plastic water sprayer. Now you can twist and pull the red water sprayer out of the end of the hose. You'll need a little hand strength to do this. Just be careful not to break the water sprayer by using a tool. They're not particularly delicate, but breaking one would render your Bissell useless until it was replaced, so use a little care.
\015\012When you've removed a red water sprayer from the hose, put the outer end of the red water sprayer in your mouth and seal your lips around it, and try blowing through it. You can't blow air through it, right? It's clogged. Open up a paper clip and push it back-and-forth through the small hole in the end of the water sprayer back towards its middle. You'll probably push out a line of white mineral deposits. Clean them off the water sprayer with the old toothbrush, and try blowing through the water sprayer again. If air passes through clearly, you've fixed it. Now you have to put it back together. Push the water sprayer back on the end of the hose. Use the pliers to reposition the brass clip on the end of the hose over the water sprayer. Push the red water sprayer back into position in the base of the Bissell.
\015\012Now do the same for the other red water sprayer.
\015\012I had a problem when I fixed this on mine this morning, because when I pulled one water sprayer off, the hose advanced up under the spring and I couldn't reattach the red water sprayer, because it couldn't reach the end of the hose. So try to use the brass clip or some other means (rubber band, tape, another clip) to keep the hose from crawling up inside the spring after you pull the red water sprayer off the hose. If the hose gets up under the spring anyway, despite your best efforts, I fixed this by removing the six screws on top of the Bissell base (the surface of which the water tank mounts on top of), and then pried it up. You can pull out the hose, reattach the red water sprayers to the hoses, position the hose *very carefully* inside the base (there are mounts under there they need to fit into, so you don't break anything), push the red water sprayers through the mount holes and mount them, and then reattach the screws to the base.
\015\012There's something else you may need to do that can help get the water flowing. This one's easier. The Bissell uses pumps, which need to be primed. Sometimes an air pocket inside the machine keeps water from flowing. To prime the pumps, separate the two water tank pieces. Fill the base as usual and mount it on the Bissell without the top water tank piece. Plug the Bissell in and **turn it on**. (The Bissell must be running to do this.) Kneeling on the floor in front of the Bissell, reach up and press the soap and water release trigger at the top of the Bissell's handle and hold it in as if you wanted water to go through. On top of the water tank is a plastic grommet hole about 1 inch in diameter, through which you pour water to fill the tank. Seal that hole with the flat of your hand. You'll feel a bit of suction. Lift your hand up and down a few times. Release the trigger and repeat a few times. Now that you've cleaned out your water sprayers and primed the Bissell's internal pumps, I'm hoping water will GUSH through your Bissell once again.
\015\012As you probably have learned the hard way, as I did, it's VERY important to do a lot of cleaning of the Bissell after each use, more than the manual tells you to do. Clean the bottom of the unit. Empty all the water. Thoroughly rinse out both water container pieces. Unscrew the three clear plastic pieces, one in front, two on the sides, that surround the brushes, and rinse them thoroughly in water. Clean off the brushes and all the lint and gunk around and above the brushes. (A water spray bottle and toothbrush are helpful here.) Tip the machine and blow all the water out of the hole in the base. Release the red clip springs on the red water sprayers and blow on them. Doing this will slow the failure of the Bissell. It's a great little machine for the money, but it does have a learning curve and need more pampering than a vacuum cleaner, doesn't it??
\015\012Good luck!
Repair Help & Product Troubleshooting for Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My bissell 9400 pro heat steam cleaners sprayers are clogged again...how can I fix this with out taking it to a shop to get fixed?

The water sprayers on your Bissell are probably clogged. I had this problem this morning, myself, with my machine, about 15 months old. They get clogged up with mineral deposits. This is a *fairly* easy thing to fix yourself. Read all the w ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Help I live in kansas city kansas and I was wondering where there is a shop that I could take my carpet cleaner to and have it fixed. I think the water hose is clogged and I don't know how to get to it.

Call Bissell at:Service Center Dept. Phone Number:(800) 457-1509\015\012They will give tell you where you can take yours to for repair. ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

After two years, my Euro-Pro Shark Steam Mop, Model S3101, no longer ejects steam. I have used tap water. I think the line is clogged with mineral deposits. The light is on when plugged in, and the unit heats up. I even put in vinegar for about an hour to break up the calcium deposits, but it did not correct the problem. How do I fix it, or, where can I take it locally to be fixed (Orange County, CA)?

Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

My Hoover SteamVac has been doing a wonderful job but in two instances, after emptying the dirty water and reattaching the reservoir, the machine has lost suction. The first time I was able to make it work again after taking it apart and putting it back together about 10 times. I don't know what I did that fixed it but as long as it worked again, I was happy. But it's happened again and I can't get it to vacuum. I can see that it isn't clogged. Can you please help me????

Look for the lower tank filter to be clean. also make sure the lower tank lid is on properly. latch when installed on machine. Make sure the front panel duct is on the lower tank. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Dirty filter caused vacuum to swtich off mid-use. Filter's cleaned, but machne won't start again. Is there reset switch or do I need to take it in to get fixed?

... Westinghouse WST1551 Wired Deluxe Upright Vacuum

I have a clogged hose. How can I take it apart to get the clog out? or what can i stick up it to get it out?

Most vacuum cleaner hoses can be unplugged at some point. One way to clear a clog is to reverse the hose & let the vacuum **** the clog out the way it went in. If you have to remove the clog manually, a length of coat hanger wire, with a small ho ... Fuller Brush FBPTCAN Bagged Canister Vacuum

Hoover tempo upright is clogged. I can only vac for a few minutes, then I have to unplug it and turn it over and clean out the under part under the roller. It is totally stuffed with dirt and dust and carpet fibers. I have a new bag in. It is like it is clogged up inbetween the bag and the roller. Also gets clogged when using the hose. It is maybe a year old. How can I take it apart and unclog it?

Disconnect the hose and head and wands. Drop a quarter thru the hose, the handle sometimes clogs. peer thru the wands and inspect the elbow on the head for blockage as well ... Vacuums

I have the Bissell 2x proheat. There is no water being sucked up from the bladder and the cleaning solution is not being sucked in either in order to get to the carpet. On water rinse the carpet gets wet but I'm not seeing any water going through the clear front piece. I live in Harvest Alabama. Where can I take it to get fixed if it needs it?

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Hoover F5809 Hello, I seen a few of your post and was hoping you could help me. I just became a member today. My sister gave me her old Hoover Steam Vac-Model F5809. This thing is so dirty and clogged because my sister has pets. So far I've gotten it all taken apart to clean it. I'm not a newbie and taking apart and fixing things. I have fixed things like microwaves, washers, dryers, dishwashers (still learning about TV's-very hard, hehe). Anyway, I got what I believe to be the motor cover off.

That cover is the called the fan cover and is usually pressed on. Tapping on the edge with a flat blade, you may be able to get it off and hope you don't bend it up, you will to put it back on tight enough so it will stay in place. Another thing to ... Vacuums

After fixing the pull cord on the poulan pro ppb30 /30cc backpack blower i can not get the cord to pull back in if i pull it. how do i get the correct tension on the recoil spring when i put it back together?

... Vacuums

There is a clog in clear tube that sends trash from floor to cylinder. have pulled out lots but cant get really far in there. can I take the hose off somehow and get in there

Try using a hanger and see if you can snake it out there might be a small hose on bottom of power head,i hope this helps thanks ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

My Hoover vacuum is not vacuuming the carpets or floors. When I release the tube to use the smaller end the suction works perfect. So i believe the problem is in the rods on the floor or in the part that vacuums the floor! Can you tell me how to fix it , or where can I take it to get it fixed? thanks

Ive just had the exact same problem. In the very back lower portion of the vacuum You will need to take it apart. I guarantee there is a clog. You might also check your belts to make sure they are still on track. ... Hoover Vacuums

I have a Polti Vaporetto household steam cleaner that I bought 16 years ago. I haven't used it for about 10 years because the connection between the steam er and the attachments doesn't work properly and it is difficult to use. The shop where I bought it no longer sells them and can't get them fixed anymore. I'm about to ditch it, but thought I would have another go at using it. (It was very expensive). Now I can't get the safety cap off so I can't fill it or test it. Any ideas on what I can do

... Polti Eco Pro 3000 Canister Steam Vacuum

The brushes won't turn. I want to fix it myself but can't figure out how to get to the drive mechanism, by taking the top cover off. I have all the screws out but it seems to have some snap fits holdi

If you turn the vacuum over and are able to turn the brush by hand and it won't turn while its running, then your belt has broken. ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

I have a Eureka Maxima, this was a gift to me, but I have to say it is the worst vacuum I have ever used. Not only do I have a problem with the suction and the filter getting clogged, but it overheats - it takes me all day to vacuum my house, because the darn thing overheats after every room. Besides for tossing it off a cliff and buying a better vacuum, what can I do?

Get yourself a dyson ... Eureka Vacuums

Can't get top apart on Sears Shop Vac to take out switch !! All screws out

... Shop Vac 925-13 Canister Wet/Dry Vacuum

Hi there ive just purchased a bissell 1623e but cant get the 1 of the 2 screws to line up and tighten in handle any tips? ive tried holding it at all angles pushing down pulling up still it wont tighten should i take it back to shop? as faulty?

Take it back as faulty no question about it should line up easy and screw in stright away ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Hoover bagless cannister 3765 - belt on power head slips off spindle. bought new belts - same problem. is this a design problem or can it be fixed? I don't want to take it to a repair shop 100 miles away and have them just put on a new belt. saw idea of smaller belt - what number? couldn't find suggested royal 104425001 belt.

I would not recommend a smaller belt. You will only wear the motor. This model series power nozzle needs to have a metal clip installed near the belt on the brush roller housing. I know that most of them left the factory without it. Remove the cover ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

I have a dc17 and there is a clog in it. I have taken the brush off, cleaned the hose, but there is something up inside the hose on the side that I can't get to. how to I take things apart so I can see to unclog it.

On the back of the vaccuum theres is a screw with a ubend hose...did you remove that? I have had things stuck in there which stopped suction? you may want to check that. also take the wand off and look through to make sure you can see light throug ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I recently put a call into dyson regarding a problem with my vaccuum and a supervisor was supposed to get back to me. no one has. back in august, we were on the phone with a technician regarding a problem with out machine. after trying a list of things, she said to take it to american vaccuum services and it would be covered by dyson. when i did, the man told me it was clogged and i would owe $45. i would not have taken it for that price! please advise as now i am stuck. i want my vaccuum and th

Unless you can Dyson to intervene and have this repair covered under their warranty, You are stuck to pay for the service. Clogs may not be covered under warranty, but I don't know how their warranty states. If it says that if you have a problem, t ... Vacuums

I have a Bissel proheat 7901 carpet cleaner and it is not sucking the water up. Normally when I clean the water gets sucked back up and I have to empty the dirty tank. Now no water is in the tank when I am done cleaning. Please help I cannot afford to take it to the shop.

I'm not sure if this will help but I had the same problem and was about ready to pull my hair out. I ended up taking the fill tank off and if you look inside where the red overflow flap is you will find a small screened opening. I found that mine w ... Vacuums

Water Leakage We have a Bissell Proheat (Pro Tech). I don't think it is the 2X model. When releasing the water with the knob on the handle, water comes out the side of the housing at the lower part of the unit. Is their a seal that my be worn out or broken. Can you give us some ideas before we take it to an expensive repair man to fix

Check the water bottle. Ours has been doing the same but putting a bit of j cloth between what they call the o ring and the cap fixed it. Really you need a new bottle assembly ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

My wand is clogged. how do I fix it? - Euro-Pro NV31 Infinity Vacuum

Dismantle and spray with a hose ... Euro-Pro NV31 Infinity Vacuum

I have a Dirt Devil Vision and when I put a clean canister back in place the suction at the bottom of the filter clogs up and very rarely go into the canister. Also where the air blows out of the motor, I will get particals that will blow out. I have checked where the belt is and also the suction tube. Do you have any ideas how to fix this problem?

Yes your intake hose is clogged thats the clear hose you can see it on the bottom from the back.disconnect the upper hose from your intake hose and try to push a coat hanger through with the end of the coat hangers end bent till its rounded so you do ... Dirt Devil M086700 Vision Bagless Upright Vacuum

Wondering if the head is plugged up because it makes a sound like air is escaping somewhere. I've replaced the original cloth bag with a comparable "O" paper bag from Sears. I tried to see if there was a clog in the hose by placing a broom handle in the hose to see if something would loosen. I also cleaned the filter and the air filter. If the head is plugged, how can I fix it? We can't get the vacuum apart. Thanks.

I had this problem, but suction improved when the attachments were properly secured in their holders. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 2.5106 seconds