Having problems with your Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum ?

Smart Mix Dial - Reassemble Cover

\015 I had a problem and had to take my the top off of our 1699V Bissell Deep Cleaner and now when I reassemble it, I cannot get the dial to line up properly with the valve on the bottom. I have found this under a similar problem, but I think it might be a different model, as I cannot get it to line-up.\015

Answers :

Hi,

Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

heatman101\012
\012gfshsg
Repair Help & Product Troubleshooting for Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Smart Mix Dial - Reassemble Cover


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

How do you get the smart mix dial to line back up when replacing the top plastic cover on a bissell pro heat pet.


First, insert the black plastic control valve all the way into the hole. Make sure that the rounded face with the cut in it is facing toward the tall part of the chamber/hole where you inserted the valve. Try to line up the dial with where the thre ... Bissell 8910 ProHeat Clear View Upright Vacuum

Bissell proheat 1698 reassembly, smart mix piston, new pump?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Bissell proheat pro tech model 7901-3 smart mix dial and valve assembly


Turn the knob to the water only, put the piston on the bottom of the knob then turn it slightly so it doesn't fall off, Start to put the cover on, when it is straight, turn the knob to the water only selection and push the top all the way down. The ... Vacuums

Broken Smart Mix Dial-How to replace


You will have to remove the top, the knob screws on but has a stop tab. Is the plastic below the knob ok, if not then you need to replace the top cover. After you replace the knob, then put the piston on from underneath, have it set to water only s ... Bissell 7950 ProHeat Upright Wet/Dry Vacuum

I THINK THE SMART MIX PISTON IS INSTALLEDS WRONG


It has the rubber seal and the container releases fluid when it depressed.... bipolar lol..\015\012\015\012fill it with hot water and prime the machine.. don't use soap just try lear the lines.. always run hot water through your machine ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Can't reassemble!!! Long story as short as possible- I removed the hood from my Bissell 1699 and can't seem to get it back on correctly. The "Smart Mix" knob and it's parts seems to be the problem. How does this line-up, or what is the best way to put it all back together? Thanks, Josh


The piston is put on the bottom of the smart mix knob, turn the knob to the water only setting, then put the top housing back in place making sure that the piston went into the slot, after the top is all of the way down, turn the knob, if it turns ea ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Smart Mix selector


I figured it out,since you nor Bissell was of no help. It turns out to be quite easy. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Bissell Pro-Heat Pro-Tech Carpet Cleaner


Put the piston on the bottom part of the knob, You want the the knob to be at the water only setting when it goes into the slot. After the top is pushed all of the way on, turn the auto-mix knob to see if it is turning easily. If it doesn't stop, ... Vacuums

Smart mix what is the trick to connecting the smart mix?


Glad you did. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Replacing Smart Mix knob


The knob itself will only go in one way, What I was talking about is when you put the top cover back on, the knob should be in the water only position. This way the piston (on the bottom of the knob) will go into the slot correctly. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

The solution in my smart mix will not mix with water and the button just keeps going round and clicks and will not stop on either water or solution.


The smart mix knob is connected to a piston that slides up and down into the automix assembly. This piston has come off of the smartmix knob and left the unit on water only setting. Sometimes the smart mix knob breaks on the ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Cleaner solution in smart mix tank not mixing with the water from the bladder. All tanks are seated properly


... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Good day, I took off the cover on a proheat upright, to install the suction diverter flap. Guy at the shop told me I had to do this but I don't think it was really necessary. Anyway, I am having a real job getting the cover back on. The shampoo mix piston seems to be causing the problem seating the two halves correctly. I see no obvious "right: way to put the piston back in. can anybody help me. Thanks Richard


Hey Richard. Turn the shampoo mix dial so the spiral is all the way at the top when you are looking at it from underneath. then, you want the piston to seat in the top groove of the knob. You want the piston's end that jets out to fit in the space ... Vacuums

Smart mix valve reassebly and alignment


Have the piston on the screw threads, put the knob on the water only setting, then after the piston is on, turn slightly so it doesn't come off, just before you put the housing all of the way down, turn the knob back to the water only setting and the ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

MOD 1699-f reassemble cleaner fluid mix switch


This is one of the most difficult machines to work on, but I can help you to reassemble the the "Automix Assembly." There is a black piston with an O ring on it that has to be put in place before the hood is put back on. This part will actually set i ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

The smart mix bottle is not dispensing any fluid. I have been using this Bissell 8910 for 6 years. The cap and seal seem to have all the parts. thanks -LaRie-


... Bissell 8910 ProHeat Clear View Upright Vacuum

Replacing smart mix plunger bissell proheat model 7901 procedure for proper installation


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem.B ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

How do I replace the Smart Mix knob on a Bissell shampooer


... Bissell Vacuums

Flow indicator is not turning and the water from the bladder does not spray out only the smart mix container emties


... Bissell 7950 ProHeat Upright Wet/Dry Vacuum

I purchased a Pro Heat self propelled Bissell rug cleaner model 7950 from Target wherehouse on 4-26-06. I used it once and all was fine. The next time that I went to use it the smart mix for the cleaning formula would not dispense formula.I called Bissell consumer services and was told to take it to Starks Vaccumn in Sherwood, Or. That was on 10-30-06 They said that it was working so I tried it again and not a drop of formula was or has been used since.I took it back 2-13-07 and the replaced the


I assume that it is spraying water? Is the smart mix knob turning freely from one point to the end? If not then there is a problem with the smart mix asm. With liquid in the soap bottle, push the valve in to see if liquid comes out ok, couild be ... Vacuums

Bissell 1699 I have taken apart the pro heat cleaner. I reassemble it. The top cover will not go all the way down. Any suggestions on getting back together. Thank you


Make sure that the piston on the bottom of the smart mix valve is in the water only position.(needs be be on the knob and not sitting in the hole). With the top off, it is easier if you have a block of wood or something under the base to hold it up. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Reassemble kirby vacuum took transmission out to replace on switch cover. now can't get it to go back together


... Vacuums

I am trying to replace the cable on a Hoover smart cyclone, however after taking all the screws out I can see the cover remains intact Can anyone help?


... Hoover Clean Smart Cyclonic Upright Vacuum

Smart mix plunger bissell 1699


This is what happened to me. The heater had to be cleaned. Easy fix. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0238 seconds