Having problems with your Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum ?

I have the bissell pro heat pet 2x and my brushes won't turn or operate...


Answers :

Check the belt
Turn dial on bottom front on the water tank to floor not tools..p.s. they only rotate when you push forward then pull back, manual motions... hope thats it
Repair Help & Product Troubleshooting for Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have the bissell pro heat pet 2x and my brushes won't turn or operate...


Check the belt ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell pro heat 2x healthy home brushes wont turn


Hey Brenda! Here's a link to troubleshooting steps for the brushes not turning.\015\012http://www.bissell.com/FAQDetail.aspx?id=1128&cid=ccsocial ... Vacuums

My bissel pro heat cleane's brushes stoped. I checked the belts. They are okay. There is no sign of heat or problems around the motor. Is there a mercury switch some where in the handle so the brushes only turn when the handle is lowered?


Depending on which model you have, you did not say, if the cogged belt goes to the pump pulley, the cogs may be wore away or and won't turn the brush roll. On some other moels, there is a brush roll motor that may have gone bad. ... Vacuums

My bissell pro heat carpet cleaner is not working properly...the scrubby bar is not turning... the belt is intact and working and it is turning the knob inside but the brush bar does not turn


How are the bearings? Maybe the motor that drives the belt is burnt out. ... Vacuums

Bissell 9200 pro heat carpet cleaner , brushes won't turn, both side belts are good. bad brush motor? or brush moter belt?


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Bissell Pro Heat 2X carpet cleaner and the brushes spin, then stop. I turn it off and when I re-start, the brushes do not spin until I push foreward. The it spins and stops again. Both belts are tight. The brushes spin if held above the carpet, but upon contact with carpet it stops. Same thing on a hard surface.


The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

My Bissell Pro-Heat 2x 12 amps Model 9200-2 The rollers wont turn and the water wont release


WON'T SPRAY ??? ... Bissell 9200 Upright Vacuum

I have a Bissell Pro Heat Carpet cleaner and the brushes will not turn. The pully is not turning the belt.


If the motor shaft that rotates the belt to turn the brush does`nt turn you have motor problem`s if it does you need to free up what ever is keeping the brush froom turning freely ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I have the Bissell Pro-heat 2X which is new and only used one time and today I am trying to use it and the brushes will not work at all. They will not turn and spin like they are suppose to.....Please Help ! John Baumgartner Roanoke, VA


Look on the front of the little gree guy and where the switches are you should see a small diagram of a brush above or below one of the switches flip the switch to the brush diagram ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Bissell Pro Heat 9300 brushes won't turn before and after replacing belts


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Our Bissell Pro heat Select Pet 2 x was given to us...no manual. (about 3 yrs old) The brushes do not rotate and water/shampoo does not come out when you hit the switch. We have looked it over and cannot find anything wrong. any suggestions?


... Bissell Vacuums

Brush Bar not turning on a bissell pro heat 2x


Here is the Instruction or User Manual for the 9500 series machineswill give instructions how to check and change drive delts ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell pro heat X2 I need the directions, I lost them. I tried to use it, the water will not come out and the brushed do not turn all the time


Follow the link below to access the User's Guide.\015\012http://www.bissell.com/searchresul ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

How do i put the brush back on a bissel pro heat pet shampooer


... Bissell Vacuums

Bissell pro heat 2x brushes are not turning???


Brushes are controlled by belts. They must have come off or broke. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissel pro heat /brushes do not turn


Belt worn or hair build up can clog it from spinning. I've seen this on other models. Just remove the hair slowly. If the Belt is worn you can replace that from Bissel or any store that sells their product.Check to ensure that the p ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My bissell proheat carpet cleaner wont turn on. Its plugged in and everything but wont turn on. I've had it for a few years but its always worked before. Do they have to heat up if I haven't used it in a while?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Bissell pro heat burshes will not turn


You need to replace the belt. Here is the belt you need:Bissell ProHeat Belt ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

We think our Bissel Pro Heat Pet is a piece of junk. It will not spray cleaning solution.


Here's a link to troubleshooting steps to assist you. http://www.bissell.com/FAQDetail.aspx?id=1122&cid=ccsocial\015\012If yo ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissel pro heat unit brushes will not engage


Keep in mind they only turn when the handle is down. if that is not the problem, it is usually the belt.David ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Brush not moving in Bissell pro-heat


If the belt is more then 6 months old or more, then the belt will have to be replaced reguardless of the way it lookes. belts can stretch over time and when you put the machine on the carpet the friction causes the brush to stop because the belt has ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a


... Bissell ProHeat Deep Cleaner Upright Vacuum

I have a bissell pro heat water wont come out


The water sprayers on your Bissell are probably clogged. I had this problem this morning, myself, with my machine, about 15 months old. They get clogged up with mineral deposits. This is a *fairly* easy thing to fix yourself. Read all the way to ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have a bissell pro heat water wont come out


The pump may spin but the vanes inside could be broken or worn enough that they are unable to push water through the pump system. I am repairing a Bissell Model 8920 Pro-Heat 2X that has this very same problem.\015\012\015\012I tested all ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Brush bar wont turn, Bissell smells like burning rubber


The belt just goes from the motor shaft to the brush roll. Do the ends of the brush trun freely, or is one of them froze up, if so replace the brush roll. If it is ok, try to turn the brush roll by hand, maybe the belt got pinched and won't move. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1174 seconds