Having problems with your Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum ?

My bissell powersteamer isnt suctioning the water


Answers :

Please try the following suggestions to see if you can get your machine suctioning properly:
\012


\012

1) Remove the Tank-in-Tank Assembly and place your hand over the motor intake valve. This valve is located next to the Floor Nozzle gasket (at the top of the Floor Nozzle window) and behind the SmartMix Bottle. If you feel vacuum-like suction at this area, your suction power of the unit is working but air is escaping at some point. If there is no suction at the motor intake valve your machine will need to be inspected by an Authorized Service Center Technician.
\012

2) It is possible the Floor Nozzle on your machine is inserted incorrectly. This would directly affect the suction of your machine. Please follow the directions below for removing and replacing the nozzle.
\012

Before starting, please be sure the machine is unplugged and the machine handle is reclined.
\012

To remove the Floor Nozzle window, first detach the Phillips head screws located at the base of the nozzle. Then, remove the Tank-in-Tank Assembly. Next, pull forward at the top of the Floor Nozzle window to release the tabs of this window from the receiving holes of the machine. This window is designed to allow access for cleaning.
\012

When replacing the Floor Nozzle window, please be sure the tabs at the TOP of the nozzle are properly inserted into the receiving holes provided. If you do not have the tabs in place properly, the suction power of the machine could be affected.
\012

Rotate the window down into place and replace the screws.
\012

3) Ensure that the Ready Tools knob (diverter knob) is in the proper setting and the valve opens and closes freely. Ensure the black foam gasket is in place under the valve.
\012

4) Check to ensure the Tank-in-Tank assembly is seated properly and that it is not full of dirty water. (If this tank has a drain cap, make sure it is in place and that it has a black o-ring).
\012

5) Check the float and baffle to ensure they are properly installed on the Tank-in-Tank. The larger square portion of this part should be below the clear baffle of the tank with the red flag portion of the float resting on top of the baffle.
\012

6) Check the Tank-in-Tank and lid for damage. Is the lint screen clogged? Make sure the lint screen is in place on the tank lid and not placed into the motor duct. Also, clear the holes on the lint screen.
\012

7) Check to see if the upholstery hose has suction. If the hose has suction and the floor nozzle does not, check the diverter valve to see if it opens and closes freely. This can be seen through the Floor Nozzle window as you switch the diverter knob from the floor to tools setting.
\012

Repair Help & Product Troubleshooting for Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My bissell powersteamer isnt suctioning the water


Please try the following suggestions to see if you can get your machine suctioning properly:\012 \0121) Remove the Tank-in-Tank Assembly and place your hand over the motor intake valve. This valve is located next to the Floor Noz ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Need a user manual for bissell powersteamer #1697-w won't suction water up need to know how to clean machine


You can view one here:Bissell 1697 Manual ... Vacuums

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet


Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn't blocked as well. ... Vacuums

Bissell powersteamer model 1693 not sucking up water


I have the bissel power steamer / powerbrush # on front at bottom 310-3150 bought in october used it 2 times 3rd time it started acting up as follows\015\012cleaned all parts. the spin dial wont spin. the switches on both steamer and hand wand ... Bissell 1693 PowerSteamer Upright Vacuum

I got a used bissel 1720-9 bissel cleaner..It holds water,,and turns on but no water comes out the nozzel?? what side of tank do i put the water in also there was no instructions,,there is suction when i turn it on but no water,,


You can download a user guide from www.bissell.com Just type your model number in the search panel ... Bissell 1720-1 Little Green Wet/Dry Vacuum

My Bissell ProHeat 2x is pouring water out of the bottom anytime it's turned on. I had it in the shop for no water, took it back again for the same problem, took it back again because it had no suction, finally took it apart and found the problem with the suction and fixed it myself. Worked fine for a day and now it is constantly leaking water, if it's turned on, and is useless for anything except for making a mess.


Took the unit apart and discovered my heater had small pinholes in the metal and they had put in silicone, instead of a gasket, which didn't seal. So much for the place I took it to "saving" my heater for me. I repaired it myself by getting a few o ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell powersteamer i have a bissell powersteamer my aunt gave me, but do not know how to operate it to put the water and cleaning solution in it. please let me know how to operate. or how can i get the operation guide or manual


BISSELL User's Guides can be downloaded at www.bissell.com\012On the front page under Customer Service click on User's Guides and enter the model number of your unit.\012User Guide will be displayed as a PDF file. ... Bissell 8806 Powersteamer Upright Vacuum

Top tube connection on water pump for Bissell PowerSteamer 1698


It appears to be the tubeing for which you speak of. ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

Bissell pro heat 25A3 won't suction up water


... Bissell Pro Heat Deep Cleaner Model 25A3, 1 ea

The clip that connects the water base to the top of the suction area broke off..where can I get a replacement base (the part where you put the water in and has the bag where you also store the dirty water)? I have a Bissell proheat 2x


Here is the number for Bissell, they can tell you who to contact near you.\015\012Service Center Dept. Phone Number:(800) 457-1509Service Center Dept. Fax Number:(800) 517-9535Hours:M-F 8:0 ... Bissell Vacuums

Hi I own a Bissell Proheat Powersteamer pro-tech with a turbobrush. I have been using "bissell multi-allergen removal formula for carpets and upholstery." I ran out of that last night. Today I went to walmart looking for more. Everything I found said "2x Ultra Concentrated Bissell multi-allergen." I'm confused on where to add the cleaner. I have a water tank and a separate soap tank. The instructions on this new cleaner bottle say to add 4 capfuls for the formula tank and dilute with hot tap wat


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

I have a 9300-1 bissell carpet cleaner and when i used it today the vacuum was not sucking the water up. i know its working because when i take the water tank off i can feel the suction from the valve that connects to the water tank. any suggestions...


... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

My bissell will not suction water from the carpet


Please check the following:\012 \012First check the motor duct gasket. The motor duct gasket is visible once the tank is removed. It is located underneath the handle on the top of the base of the machine. It has a black rubber coating aro ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My bissell powersteamer deluxe 1694 won't suck up water


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Have a bissell pro steam cleaner the suction is great but the water leaks out the bottom I think it should spray from the front and the soap cleaner won't dispense from the bottle so I have to mix the soap cleaner in with the water Any solutions


Use this guide!\015\012http://newzealand.bissell.com/images/IncludeContent/Service_Center_Help ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissel shampooer I have a bissell shampooer powersteamer power brush model 1694-W. I cant get it to dispense water onto the carpet anymore. I think it's because I let my 3 year old ride on it while I was shampooing. I assume I have depressed some special little part that is now broken or mashed or something. Stupid I know....


Yes there is a belt on the side that will need to be changed ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Bissell powersteamer # 1697 filled it with water and soap in the container and the motor runs but it doesn't work, water won't go through and it won't pick up anything. Checked and the belt is fine.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

My bissell does not **** up water very well - Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

My bissell pro heat 2X has stopped dispensing water from the tank, the suction is working and it seems to be dispensing the detergent, so it is not rinsing or washing with water. I have cheaked to see if there is a blockage but that doesn't seem to be the problem...please help


I have a Proheat 2X and had the same problem. I tried the Water Rinse setting and found water came out and was suctioned properly, but on the Light Clean, Normal Clean, and Heavy Traffic settings, the unit failed to do anything. Problem may be with l ... Vacuums

I have a bissell 1698 powersteamer. i have already cleaned heater and completely cleaned all parts , checked the mix piston, checked belt. it will not shoot water or mix. the motor runs, it will **** water and the brush turns. is it the pump and does the pump just shoot the soap?


Pump is probably bad. When you put the lid back down, did you put the piston on the bottom of the smart mix knob? Also the smart mix knob should be in the water only selection when the top is pushed all of the way down. Also sometimes the flow ind ... Vacuums

Bissell proheat power lifter model 1698carpet scrubber. When the trigger is pressed, no water comes out to clean. The suction is working fine, however the water is not.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

I have bissell Model 1697 Powersteamer Pro. i filled bucket up with water and no water is releasing when I try to steam clean, carpet is dry.Am I filling it up correctly, manual lost. Is there a way to view the online manual.


The pump belt may be worn and that is why it is not dispensing water. Here is a link where you can get the belts and you can view the manual: ... Vacuums

Water suction My Bissell Proheat Clearview is not sucking up water into the tank, motor appears to be fine


Here's what I did. On the top of the water bucket there is a red oval screen, remove and clean the screen and replace. Also, next to the screen is an oval opening which meets up with a black oval gasket on main unit. Inspect the gasket and replace if ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

My Bissell 9200 is not sucking the water into the dirty water resevoir. 1. The gasket on the clear-view seems fine. 2. The suction power just doesn't seem powerful enough (feeling with my hand). 3. The brushes turn fine and belt is fine (not sure if that even matters for this issue). Any help appreciated. Thanks, - Matt


Disassemble all lines and check to see if all O rings are installed. If cracked missing or stretched out of shape no suction will be provided ... Bissell 9200 Upright Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o


Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0815 seconds