Having problems with your Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum ?

My bissell proheat is not spraying water on the floor or from the hand tools. the suction is working and the brushes are rotating fine. what do you think the problem could be? thanks!


Answers :

I want to know the same thing...
Repair Help & Product Troubleshooting for Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My bissell proheat is not spraying water on the floor or from the hand tools. the suction is working and the brushes are rotating fine. what do you think the problem could be? thanks!


I want to know the same thing... ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Mine does the same thing. There is no suction. I found that there is a door that opens when you tilt the handle in the down possition. I think there should be a spring in place so it can open. Until I find a replacement spring I have to open the door ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Hoover Windtunnel My Hoover Windtunnel is 3 years old. It worked great until yesterday when it lost all suction. I have followed the manual to trouble shoot any possible clogs and could find none. Then I noticed that when I remove the dirt collection cup and held my hand over the vent the suction is fine and strong. So... I replaced the hepa filter thinking that might be the problem. That didnt' work. The motor runs fine. The suction without the dirt cup inserted is strong. As soon as you insert


Either the hose has a clog, or the inlet down by the belt is clogged. Is there suction at the end of the hose, if not then it is clogged. If there is suction, then it has to be clogged down below by the brush roll, check that inlet. There also is ... Vacuums

I have a vax cylinder model V-094. Working fine then started to play up. Switch it on and the motor seems to struggle to power up. Kind of wurrs up and down. Was thinking it could be the brushes have worn. Tokk to bits and cleaned her up, took a look at motot and brushes, cleaned them too, back together and still them same problem. Help please, hoover is not old but has done some work really don't want to through away something that can be fixed.


Hi.\015\012\015\012after all you have done I would be pretty confident its the motor thats faulty they are expensive to buy so machine is going to be scrap,\015\012\015\012Sorry.\015\012\015\012 ... Vacuums

I have a Bissell proheat2 turbo carpet cleaner. The power brushes have stopped rotating. The brushes are free to turn by hand . The motor works fine with good suction. What is the problem ?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Poor suction The actual sweeper seems to work ok, but the hose attachment has some suction but not enough to pick up things I think it should and not enough to make the power brush spin. I've checked everywhere I can for clogs, but I can't see anything. And there doesn't seem to be any way to check to hose itself for clogs. I've cleaned out the container and the filters, but there's still a problem.


Check the inlet down by the brush roll, make sure it is open, if it is then the hose itself must have a clog. If the hose comes off, drop something like a marble in one end and see it it comes out the other end, if it doesn't then you have a clog. ... Dirt Devil M1100009 Reaction Soft Touch Cyclonic Upright Vacuum Cleaner Vacuum

The tool attachment for the hose on my Bissell ProHeat 2X CleanShot won't spray soap or water. The bristles on the tool rotate without a problem and the suction is working fine, it just won't spray water when I pull the little gray trigger on the tool.


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My purple Dyson Animal (without the ball) isn't working correctly. When I turn it on, the red power light, as well as the medium pile buttons flashes. When I first turn it on, the brush rotates for 3 to 5 seconds, then once I start moving the vacuum, it stops and that's when the lights start flashing. I've checked the filters, they are dry and installed correctly. What could be the problem?


I need help repairing my Dyson. I cannot push the buttons down to select Short pile/Medium pile or bare floor. The buttons will not push down at all. It will not allow me to select anything. I have very short pile carpet so it does not pick up that w ... Dyson DC28 Animal Bagless Upright Vacuum

I have dirt devil envision M086710 less than a year and rotating brush does not work ? 'everything works except suction from rotating brush ..


... Dirt Devil CE5500 Floor Keeper Upright Wet/Dry Vacuum

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920


You need to change the belt(s). You can find the belts for this model here. http://www.vacbelts.com/bissell-proheat-belt-combo-pack.htm ... Bissell 8910 ProHeat Clear View Upright Vacuum

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920


The brushes will only work if the handle is released and the ProHeat vacuum is running . There is a micro switch inside the lower handle that switches on the DC carpet brush motor. The DC power for the motor comes from a Bridge Rectifier on the PC ... Bissell Vacuums

My Roomba only works correctly when I leave out the rubbery type brush (not the fiber filled brush)...... when I leave the rubber one in, it doesn't pick up & then finally stops & says REMOVED BRUSHES..... I have cleaned every nook & cranny of this thing... inside & out. I finally found that if this one brush is left off.... it works great & has for 2 weeks??? What could be the problem?


Hi,\015\012First let’s try one more time to clear out anything that might be caught inside. For this disassemble the green brush cage unit, partially, from the blue box. This would expose the cover of the gear box. On t ... iRobot Roomba 560 Robotic Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi


Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

Currently my dyson does not work when in the upright position. When I pull the handle back, it will run, but the suction is not very good at all. I tried washing the filter, but that didn't work. Sometimes it works for awhile, but then the problem occurs after the machine has been used for awhile. What do you think the problem is?


Hi its Darran at Dyson.It sounds as though the brush bar may not be turning properly when you put the machine into the upright position. To test, lie the machine on its side in the vacuuming position (head released) then switch it on and ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!


Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums

My pet hair eraser rotating brush does not rotate. I read the manual and cleaned the brush and placed it back correctly, but it is not working when I am using it. If I lift the vacuum from the flour, it starts rotating so I think it is the matter of the amount of contact to the flour. what should I do?


... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

Suction hose I can't get the suction hose to work...and I have cleaned it out to make sure it isn't plugged. There is a small amount of suction just not enought to pick anything up.....the floor part works great...what could be the problem


I would first double check the hose, remove it and drop a marble through it to be sure. make sure the bag is new and also check the filter underneath the bag if it is clogged it could cut the suction. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My model F5906-900 --- problem is the brushes have stoped working... I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly... onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it's ab


(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover F5906-900 Upright Steam Vacuum

Hoover upright bagless vacum.motor runs, brush turns, no suction through hole behind brush roller. however there is suction going out of dust cannister filter flap to motor. what could possible problems be?


Sorry to read about your problem, I hope this helps you out.you have a clog between the brush and bagI tried to help you. Please help me and Rate/Vote on my response, thanks and good luck ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a InStyler (the rotating iron) by Tre Milano. This device is for styling hair. This is not a flat iron, but a cylinder that warms up and rotate's against a brush. It has 3 heat settings which works fine. Problem is cylinder has stopped rotating. My husband disassembled and believes the motor for the rotation has worn out? This is the question he had and mine is can it be replaced ? I have model number. . IS-1001 120v 60hz 135w. Conforms to UL STD. 89 0927-037875. Also stamped on the small


I'm repairing an Instyler right now. \012Troubleshooting, I connected a multimeter and measure the voltage where the motor is connected. When I push the button that makes spin it, I measure 12Vdc which is a correct value for that motor. Then I co ... Vacuums

After using switch to go from floor to carpet, noticed the roller brush not working, and therefore the self-propelled feature also not working. Replaced what I thought was the problem, a loose belt, but still does not work. Motor runs and there is suction...???


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

I have a CT600 power brush that would not power up. Thinking the motor was bad in it, I replaced it with a new CT700 power brush, I am still experiencing the same problem the power brush itself does not seem to be getting electic power, but the Vacuum unit does come on with suction.


First try connecting the power nozzle directly to the hose. If it works, the problem is due to a broken wire or faulty connection in the wands. At least one wand will need to be replaced.\015\012My guess is it's probably due to a broken or di ... Broan-NuTone VX550 Bagged Central System Vacuum

My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn't sound right a


Trace the path of the suction into the tank and see if there is anything loose or ingested.\015\012Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

No suction vacuum working fine and suddenly, no suction at all....what could be the problem? no suction through the machine from either the wand or the floor/brush side


Sucked up a sock?? No seriously.. it may be as simple as that or that an on board filter is clogged. Check your manual for all filters and Hepa/screens and others. Also, is the unit making any odd noises since the non -suction scenario? Whining or s ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have a Eureka Mega Boss Central Vac Model # CV1801P. The suction works when the handle button is pushed left (floor mode) but no suction happens when the button is pushed right. When the floor attachment is hooked up and the button is pushed right, the brush rotates, but there is no suction.


... Eureka Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0948 seconds