Having problems with your Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum ?

Model 6801-3 The brush will not spin on the power head. The belt is secure. The entire thing has been cleaned inside and out.


Answers :

Repair Help & Product Troubleshooting for Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Model 6801-3 The brush will not spin on the power head. The belt is secure. The entire thing has been cleaned inside and out.


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a


... Bissell ProHeat Deep Cleaner Upright Vacuum

Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems


Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums

How to disassemble the brush to empty anything that might be stuck inside of the brush? The motor seems to be overheating, all belts have been checked, all airways are clear and the filter is clean. The vacuum is vibrating and releasing a burning smell, but still sucking up dirt. There is nothing stuck on the outside of the brush, but is there a way to check inside of it to see if that is where a clog is occuring?


If there's a burning smell and the belts are fine, the problem is going to be hot wires causing the insulation to melt, or the motor going bad. Discontinue use and have it checked at a repair shop. ... Bissell 6594 PowerForce Bagless Upright Vacuum

What causes these things to become unbearably loud? We've cleaned evey filter on the machine, pulled every speck of hair and lint off the brushes, changed the belt, no clogs anywhere. I've totally (and I mean totally, down to the brushes on the motor!) torn this thing down and put it back together with no difference. Also have a Eureka bagless, and after minimal use, and almost anal retentive maintance, it does the same thing,to stinkin loud. Wish one would **** up the other to save a trip to th


A clog in the hose or dirt inlet by the brush roll will cause the motor to sound loud. But so will a bad motor bearing, or motor fan, in which case you would have to replace the motor. ... Bissell Vacuums

My Roomba only works correctly when I leave out the rubbery type brush (not the fiber filled brush)...... when I leave the rubber one in, it doesn't pick up & then finally stops & says REMOVED BRUSHES..... I have cleaned every nook & cranny of this thing... inside & out. I finally found that if this one brush is left off.... it works great & has for 2 weeks??? What could be the problem?


Hi,\015\012First let’s try one more time to clear out anything that might be caught inside. For this disassemble the green brush cage unit, partially, from the blue box. This would expose the cover of the gear box. On t ... iRobot Roomba 560 Robotic Vacuum

Hi, There is a high pitched whirring sound coming from lower part of the vacuum. When I tilt it toward me (while standing in the normal vacuuming stance) the sound sometimes lessens for a minute or so. I have tried the following things: -cleaned the two sponge filters -emptied the dirt receptacle -removed the roller and cleaned it -cleaned the brushes -the belt is not ragged and does not seem floppy -checked all of the airways for clogs (including removing the wheel base) Can you help?


Your looking for some dirt stuck in some thing you didn't check yet. with the roller out and the belt out of the way run it to see if it still makes the noise. if it does then you looking at the impeller or the motor bearing themselfs those bearin ... Bissell 3750 Lift Off Bagless Upright Vacuum

I took the cover off the brush so I could cut off all the hair that was wrapped around it (vacuum was working fine, I just noticed the hair). I pulled the brush/spinner thing off one side, cleaned everything, popped it back in where it belonged, and tried to make sure the belt was in the proper alignment. However, when I turned the vacuum on, it makes a horrible noise like I'm sucking up rocks. What have I done wrong in putting it back together? It seemed simple...


The ends of the brush roller have to go in in a certain position.each end has a different look.make sure the match up to the seats on the roller guides and make sure the belt is centered.the belt will center itself by turning the roller by hand in on ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I am replacing drive belt on Eureka 4870 upright. Before installing I removed bottomplate and was cleaning out accumulated lint, hair and grit. Found a pair of identical (reciprocal) felt gaskets sucurely inserted above and below the roller brush, and one small loose piece of felt approximately 1/3 inch wide by 1 inch long that came out as I was pulling out debris. It has a slight crease across the middle as though I was not resting on an entire flat surface, but I find no other clues as to wher


If you go to this URL:\015\012\015\012http://www.VacPartsWarehouse.com/Eureka-4870-Ultra-Smart-Vac-s/1928.htm\015\012\015\012in the exploded view of the unit, identifying the parts and look at item 18, I believe it is where your felt part ... Vacuums

I have a dc17 and there is a clog in it. I have taken the brush off, cleaned the hose, but there is something up inside the hose on the side that I can't get to. how to I take things apart so I can see to unclog it.


On the back of the vaccuum theres is a screw with a ubend hose...did you remove that? I have had things stuck in there which stopped suction? you may want to check that. also take the wand off and look through to make sure you can see light throug ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hoover windtunnel t series belt is loose- roller brush doesnt turn. Its brand new belt is slipping. we bough new belts and putthem on same problem. Can not find solutio in manual. Is the belt supposed to go around the "metal pulley". I know it goes around the little metal motor thing, then thru the guide and around the brush. What is the metal pulley??? Is is the larger round silver thing between the guide and roller?


I also have a loose belt and have bought additional belts but have the same problem. I put the it around the metal rotor and around the brush roller a shown by he Hoover video, and it is loose. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o


Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom


Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

It clicks as it is going and stops after about 30 seconds. Two beeps. I have tried cleaning brushes and have pretty much taken the whole thing apart, cleaned the motor, the brushes everything. Still doing to same thing, when this has worked before.


It clunks because the gears are damaged. You will need to replace the CHM. If you have the red cleaning head module, chm, replace it with the green chm. ... Roomba Robotic Floor Bagless Vacuum

Brushes only work when Dust Bin is removed!! I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'


HI, If the brushes work , without the bin, the problem , the problem could be caused , due the failure at the bin lock mechanism. There is a sensor that checks if the BIN is connected properly or not. This problem is best resolved by getting ... iRobot Roomba 560 Robotic Vacuum

The brushes spin very, very slowly and stop altogether sometimes - like they just don't have any power behind them.I've cleaned the brushes and also turned it on without the brushes inside to see if the female plug that the brushes go into turns - it does, but not very fast. My husband said he thought he smelled something - like burning. Is there a way to take the underside cover off and clean something?


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover windtunnel U6425-900 the brush roll is not turning. Both belts are in good shape, I cleaned the brush roll and it is free of debris, the setting is on carpet and the brush roll still will not turn. There is a "burning rubber" smell when you attempt to push the vaacum forward a few times. The small belt does not seem to be pulling properly but appears to be in good shape.


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

No matter how many new belts we put in the brush will not rotate when it touches the floor. If you hold it straight up the brush rotates like crazy. Why is the brush not cleaning the floor. Yes, I have the right belt. It is R we have the boss. 12 amps. Model 4870


There is probably an accumulation of slippery stuff on the shaft that drives the belt. You can scrape it clean with a sharp knife or a razor blade. You might need to use some kind of solvent to get it clean, and if you do, be sure to follow up wit ... Eureka Vacuums

On our Hoover U6445-900 (Mach 6.9) we replaced the small belt that goes to beater brushes in front of unit. Upon starting, the Hoover quickly got hot and smoky. We shut it off and looked things over carefully, but the second try also resulted in friction heat on the belt. Now it appears the belt may have stretched due to heat and the brushes won't spin. Any ideas?


Are you sure you purchased the right size belt..the friction you speak of is usually caused by a belt not being the right tightness or a jammed beater brush ... Hoover U6446-900 WindTunnel Bagged Upright Vacuum

I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'd stop here first before calling again! Than


Ok, this is a "Brush Height Adjustment" issue. It will probably work great on a hard surface but on carpet the brushes bog. If you've taken the unit apart already...Sorry....do it again. When you do, you'll see a String which allows the brushes to " ... iRobot Roomba 560 Robotic Vacuum

Dc07 problem I have a dc07 cyclonic vaccum and like this model,however, for some reason,it has been very dificult to push and pull for the past month or so. i have completely cleaned the brush assembly,cleared any obstructions in the hoses,and, cleaned the filter.I also checked the belt tension,wich i thought was fine but to no avail.Be advised that the brush assembly is spinning and suction is excellent. It just feels like the brush drags along the carpeting. this is a great vacuum cleaner and


The dyson uses two belts, one from the motor to a clutch and then from the clutch to the brush roller, the belts that they use are not much better then any other belt ( those you should change yearly ) but you cant just change the belts you have to c ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.


... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

Roomba discovery My roomba comes off the charger and will go about a minute and a half. Then it will stop and beep once. i checked roombas sight and they said that the brushed need to be cleaned. I cleaned the brushes 6 times. It still does the same thing. I bought it from you in November of 2007. Should I bring it back to your service department?


Greetings doreen f,\015\012\015\012The roomba unit carries a one year manufacturers warranty, so you should be able to bring it into your local Best Buy™ store and have them try to repair it. \015\012\015\012I hope this ... Roomba Robotic Floor Bagless Vacuum

My pet hair eraser smells like it is burning all the time and sounds funny. The brush will not spin once you have it on the carpet unless you hold it up a little while you are cleaning but then the whole vaccume is not on the floor. I have cleaned all filters and all and it does the same thing. My sister has the same machine because I raved at how wonderful this thing was for pet hair and mine has not worked right since it was about a year old and hers has had the same exact problem since it was


We had the same problem, and it turned out that the roller wheel height setting had broken, for no apparent reason, and was "floppy" so we had to lock it in to one setting with epoxy. Limits utility, but it works. Sort of. ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

This concerns Kenmore Progressive vacuum 21637115700 part 23 2CKG352000, the belt driven brush bar. I had to take it out for some serious cleaning and it expanded in length about a quarter inch as it is supossed to, I guess. How do I collapse it back so I can re-attach the belt and brush? Thank you


Hello. i can assist you. the bar will collapse back in one of two ways either direct pressure exerted on the ends or by a twisting motion applied to one end and or the other. use a pair of pliers or a wrench to get a grip on it if you need to. re ... Kenmore Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0745 seconds