Having problems with your Bissell Cleanview Helix Vacuum ?

Bissel cleanview not picking up small items on carpet. My husband checked the belt, it seems to be in place

Answers :

Repair Help & Product Troubleshooting for Bissell Cleanview Helix Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bissel cleanview not picking up small items on carpet. My husband checked the belt, it seems to be in place

... Bissell Cleanview Helix Vacuum

The hose works great, but the head of the vaccuum does not pick up anything !!! I checked every opening that may have been clogged, but nothing came up. When I hold my hand under the brush/roller, it seems to be putting out more air than intaking air. Particles "dance" on the carpet, but don't get "sucked up" into the vaccuum ? I have had the vaccuum only 1 year, so the brushes should not be a problem. I changed the bag, and checked the belt. The belt and brushes seem to be OK. ?

Hi there,Uprights are notorious for debris forming clogs when changing direction. The 90 degree turn where the base suction goes up. Have a closer look . You may need to pull the base plate off to access the blockage.Best reg ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My Bisssil cleaner will not pick up the water from the floor. I checked all the trouble shooter helps and evewrything is OK Checked all belts they are OK. It also will not pick up water with the hand held tools, seems as though the vacuum is not working

Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

ORECK VACCUM older oreck xl, new belt , new bag, checked for clogs, does not pick up as it used to, and, much harder to push, seems to grab or drag, why????

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=747767\015\012Generic problem for all Vacuums\015\012ORECK VACCUM\015\012Posted by FISHERMAN928 on Jul ... Vacuums

Bad smell after using my windtunnel for a couple of minutes i noticed an odd smell. i turned it over and checked, the belts are fine but i cleaned out the hair anyway. after doing that the self propel seems to struggle and it is hard to push. when i look through the window on the top i can see the brush spinning freely but then when i push it, it slows down dramatically and then picks up again. the suction is fine. what do you recommend?

It may be the roller bearings? ... Hoover U5450-900 Windtunnel Supreme Bagged Upright Vacuum

I have a Dyson all-floor model (not the ball). I recently replaced my carpet to a Frieze. Since replacing the carpet, the Dyson is extremely hard to push. It almost forms a "seal" with the carpet. Seems to work fine on Berber carpet and laminate floor. My husband has checked to make sure the brushes are working, hoses are not clogged and belts are OK. I've had it for about a year. It is virutally impossible to push on the new carpet. Any ideas?

Have you adjusted the brush control system. If you look at the link below page 6 will tell you how to adjust. If this is not you vacuum please give the model # of the one you have so I can help you more.\015\012\015\012 ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I cleaned out the hose and removed brush to clean and checked belt. Everything seems to work but will not pick up or suction on carpet. The hose is totally clear from clogs. I can see the floor from one end to the other. What am I missing that might be causing lack of suction?

Hi troupdavid,I see that your Vacuum is having issues with it suction, you mentioned that you took it a part to clean it, see steps below.\015\012\015\012Check if everything is inserted prope ... Hoover Tempo Widepath Upright Vacuum - Blue

When using my hoover wind tunnel the last few times it has emitted a burnt rubber smell so my husband checked the belt and is wasn't broken or off but now when I use the vacuum the beater bar doesn't seem to be going around as well as it should be can you help

I take it the belt was put back on !! i would say hubbi forgot the tension arm a little black striker that can go in two ways but put in back wards it will not tension the arm ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Generation 4 Apparently, my belt came off while vacumming. I had a lot of hari entwind on the roller, so cleaned off the hair.... but now I can't seem to get the belt to stay "in place". Is it supposed to move around on the brush? or be held in place? It seems to me when I try to get the hook to grab ahold of the belt, it is going tohe wrong way to grab it. Please HELP!

First off get a new belt, I am sure this one has stretched. Then put the belt around the brush roll, put it in the center, put the bottom plate back on. Then turn the big knob on the front and turn it until it locks, you will know if it grabbed the ... Vacuums

Hoover Wind Tunnel 7500 Brush not Turning. I have replaced the Brush and the belt. The problem does not seem to be either to me. I believe might be a missing part. The place were the belt hooks on is a metal pole which never seems to grip the belt well. In fact it seems loose most of the time and slips on the brush, causing the belt to eventually burn up. Could there be a missing plastic or rubber piece meant to hold the belt taught  on the metal pole?

Check the Idler Pulley part Number 43241004 (Item 13 in the IPB) ... Vacuums

I replaced the belt in our Eureka Boss Smart Vac, it still seems loose, it uses a type R belt. The beater belt still doesn't seem to turn properly and seems that it doesn't pick up very well when I use it on my berber carpet. We have 2 dogs and I like to use it frequently. I have changed the bags and belt......

Check to see that the beater brush is not frozen up. Pull the brush and clean it, spraying some WD40 on each end piece that holds the brush in place.\015\012Also be sure the belt is properly installed so that the brush turns in the correct direction ... Eureka Vacuums

My Bissell BS3920F upright (similar to the 10N6F) has been working wonderfully for the past 3 years but suddenly seems to not pick up dog hair as well as it used to. It has been pulled apart by my husband to ensure nothing is blocking the hoses etc and when running the suction seems to be there. It seems to grab the dog hair and leave it in a straight line directly under the unit without picking it up. I then disconnect the hose and use to hose to pick up the dog hair. This works well but obviou

Check to see if your brush is not worn down, they do wear with age - compare the length of the bristles with a new one. Replace the brush ir there is a significant difference in bristle lengths. Also check the flexible ben ... Bissell Vacuums

My Hoover Wind Tunnel Bagless Pro Pet is making a very loud thudding noise when the belt rotates, belt seems to be intact and in place, what am I missing? Vacuum is less than 6 months old, belt is not worn and motor seems to be fine.

... Vacuums

I have a Eureka Altima vacuum cleaner that doesn't pick up very well. The suction seems fine but the brush roller doesn't seem to pick up from the top of the carpet. When you lower the height of the vacuum the belt rubs and smells horribly. How can I get the vacuum to pick up better?

That means that you need to replace the belt. Here is the belt you need to replace and the manual which has instructions:Eureka Altima ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I have a Eureka 5902AVZ and the brushroll does not work. when i remove the belt, which is not torn nor worn out, the motor spins perfectly fine. Though when i put the brushroll back into place, it shows that the motor is trying to spin, but with resistance. it seems the brushroll will not spin if locked into place, because there is no attachment on the left side of the brushroll that will allow it to spin freely with the belt. am I missing some parts or is there something else wrong?

Hi and welcome to Fixya. I am Kelly. \015\012\015\012You have correctly identified the problem as the brush roll itself. \015\012\015\012There is a bearing under each end cap of the brush roll. You can gain access to the ... Eureka 5902AVZ Bagless Upright Vacuum

I have the yellow altima vac. for a while now I can not get the darn thing to pick up properly. Or should i say keep it up.. The vac does seem to be getting everything picked up but as soon as you turn it off, you have a mess under the vac.. I have checked for clogks and can't seem to find any.. I have removed the hose, Nothing there.. And yep have removed the yellow thing inside the trash cup.. Is there anything else you could suggest??

If it smells hot, then there's a strain on the motor no doubt about it. Check the suction channel behind the sole plate and remove all of the hoses to check for a clog. It could well be that there is a clog inside the machine after the dust channel f ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

** suction The best way to describe it is that when I was vacuuming I could see dust clouds at the front of the vacuum where the light is swirling around in the air. It was like it was blowing dust around instead of picking it up. I checked the tubing and found that it was clogged with some paper and hair ***** etc.... So I cleaned it out and tried it again and it still was not picking up properly. I had my husband take all the tubing apart to check for other clogging and there was none. When I

You have an airflow problem. You may still have a blocked intake or tube, also check the filter. The air is supposed to go in the bottom (of course) and I'm sure you k**w where it goes out. You probably can **te a reduction in exhaust. If this is ... Oreck XL Ultra Bagged Upright Vacuum

When I vacuum w/ the brush control in the on position it make a really loud noise, almost like a grinding sound. I have looked at it and nothing seems to be wrong, but I notice that the pin that engages the belt seems to vibrate a bit, possibly creating the noise. It started when I accidentally got part of a plastic grocery bag caught in the brush. Could it have stretched a belt? Nothing is caught any other place and it only makes the noise when the brush in in the on position.

Yes, the belt could have been stretched and is now vibrating and hitting other parts and creating a noise if much of the bag got caught under the belt. If you have another belt for this vacuum, please put it on and see if the noise stops. If it does ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn't sound right a

Trace the path of the suction into the tank and see if there is anything loose or ingested.\015\012Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Poor suction The actual sweeper seems to work ok, but the hose attachment has some suction but not enough to pick up things I think it should and not enough to make the power brush spin. I've checked everywhere I can for clogs, but I can't see anything. And there doesn't seem to be any way to check to hose itself for clogs. I've cleaned out the container and the filters, but there's still a problem.

Check the inlet down by the brush roll, make sure it is open, if it is then the hose itself must have a clog. If the hose comes off, drop something like a marble in one end and see it it comes out the other end, if it doesn't then you have a clog. ... Dirt Devil M1100009 Reaction Soft Touch Cyclonic Upright Vacuum Cleaner Vacuum

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t

The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

The brush roller stops turning and I can smell the belt burning, then it will catch and start working normal. I looked under the plate to check the belts and they looked okay and no hang ups of string or anything. The only thing that seemed weird was that the smaller belt that actually attaches and turns the roller is a bit loose. The larger belt is tight but looks like its the one that is burning and causing the smell.

Better to replace both belts the smaller one is stretched out thats whyits slipping ,be sure to clean the old rubber off the motor shaft before replacing the belts.it will cause the new belts to run unevevly and go bad before their time ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My Shark Lift Around Vacuum is not picking up items even though it seems to have suction

... Vacuums

I cleaned out my brush in the bottom front, cleaned out the small tubing going into the canister, and the canister itself. I also changed the filter.I snapped everything back into place, but Since then, it doesn't seem to have any suction and there seems to be a space between the canister and the bottom of the vacumm where the canister sits. At that area, you can feel air coming out when trying to vacumm and it just doesn't pick up, it seems to be just blowing stuff around.

You need to really look at it some thing is out of line you shooed not have\015\012any spaces in the top or bottom\015\012pull the canister back out and look at the pins that you lined up with the\015\012to ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My vax swift 1600, has began to make a huge rattle noise, no noise when brushes and belt is removed. Seems like the belt is rubbing against the side. Wondering if there is meant to be a screw or something to keep the belt in place and it has come off.

... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1013 seconds