Having problems with your Bissell Flip-It Select Hard Floor Cleaner - Volcanic Satin ?

Eureka model 4335 - belt removal (top cover)

\015 How do I remove the top cover of a Eureka 4335 so I can replace the belt?? I did not see any screws on the top or bottom.\015

Answers :

Hi.  There are 16 different models of Eureka 4335, and frankly I don't know how much difference there is between them.  You can download a copy of the user manual from the website below.\015\012
\015\012If that doesn't work for you, please re-post - stating exactly which model you've got, and I'll guide you through it.\015\012
\015\012Good luck. If this has helped, please remember to rate me!\015\012
Loosen two screws on either side on top of the housing lifts off the top. exposing the roller and the broken belt.
Repair Help & Product Troubleshooting for Bissell Flip-It Select Hard Floor Cleaner - Volcanic Satin

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Eureka model 4335 - belt removal (top cover)

Hi.  There are 16 different models of Eureka 4335, and frankly I don't know how much difference there is between them.  You can download a copy of the user manual from the website below.\015\012\015\012If that doesn't work for you, pl ... Bissell Flip-It Select Hard Floor Cleaner - Volcanic Satin

I havea Bissell ProHeat Model 7901. My problem is that the brush doesn't rotate. I have removed the access cover and both belts and found that the central cylinder for both belts is frozen and will not turn easily. Both belts are fine, except they are now burnt from this cylinder not being able to rotate. What I need is how do I remove the top cover to get at this cylinder to remove it and free it up?

... Bissell 8910 ProHeat Clear View Upright Vacuum

Agitator belt failed in my Hoover F5853-900 Steam Vacuum Cleaner. But can not remove bottom Cover .. have removed top cover and two screws from the bottom Cover. The smaller Cover is glued to the large Bottom Cover. Need help.

Hello,Unscrew the plate. check if there is any screws at the bottom, if none, exact little pressure to pull out the bottom cover. At this \015\012point you should be able to see the broken drive belt along with the two\015\012 drive bars ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Kenmore Model 116 Cannister Vacuum.Trying to get into motor area. Think belt is worn out. I have removed the front two screws under the hinged cover, but can not remove cover over motor.. Still attached at rear. No evidence of any more screws to remove.

Under the cordwinder actuator button, are your other two screws. To remove this cover, take a flat tipped screwdriver and , very carefully, find the "tabs" (there are two) both on the front section under the button. Then, Carefully, press them in a ... Vacuums

I can't find the 4 screws to get to the belt on a dirt devil 22.0 Fx. The bottom of the vaccuum says " remove four screws from bottom of nozzle then lift top nozzle cover off", where are these screws, I can only find two, and which is the top nozzle cover?

... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

I have a eureka bravo upright model 9600. I have removed the hood . I need to remove the brushe roller to install a new belt. I cannot figure out how to remove the brush roller.

Check out this URL:\015\012\015\012http://www.svcvacuum.com/beltrep2.html\015\012\015\012looks like it has just what you are looking for.\015\012Would appreciate a thumbs up on this if you find it beneficial.\015\012Paul ... Eureka Vacuums


... Vacuums

We have a Eureka Chinese p.o.s, model 6831. The brush roller won't turn, appears to be plugged with cat hair dang long hair cat. I cannot figure out how to remove the cover without breaking it after removing the screws, there is a u shaped collar on the tube in the way. Can anybody help?

There are a couple of tabs on both sides of the top housing that need to be unlocked by using a flat screw driver, then the top will come off. The u shaped collar on the tube will then give way to take the roller brush out to clean. ... Vacuums

I have a Hoover Windtunnel Farrington upright model U6431-900 It has worked flawlessly until last week. The roller brush has stopped turning and I believe it is the belt that has broken but I am not sure how to remove the cover to inspect it and replace the belt if that is the problem. Please inform me how to perform the operation and what I should I look for? Is there a site with a diagram on how to replace said parts? Thanks for any and all helpful info that you can supply me with. Larry

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783264\015\012Generic problem for all Vacuums\015\012I have a Hoover WindTunnel\015\012Posted by ... Vacuums

Upright model # el8605 cannot remove screws that hold on brush @ belt cover have tried to loosing them but they just turn and will not come off

... Electrolux Vacuums

Hoover self propelled bagged windtunnel upright model #U6435-900...how do you remove the green plastic shell cover to get to the part that secures the v belt...we need to secure the bolt and cannot get the area. Brushes and transmission wheel not rotating? thanks

Greetings from GoVacuum,\015\012\015\012Here's a great video repair tutorial that we've put together to try and help you with the repair on your Hoover WindTunnel. I hope that this helps you with your repair. If you found this solution ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Upright model # el8605 cannot remove screws that hold on brush @ belt cover have tried to loosing them but they just turn and will not come off

... Electrolux Vacuums

The on off switch is broken on my Eureka Readyforce model 900. There are no visible screws and I can't figure out how to remove the cover with the swith.

Underneath there's a 1-inch long screw at the bottom of a three-inch deep hole. On top, if you raise the bag cover a bit, you will see a screw in a hole on each side of the vacuum. Close the cover, you don't see the holes, open the cover too far, y ... Bosch Eureka Readyforce Bagged Canister Vacuum, 900a

Eureka Fantom Thunder 12V/older model Need instructions on how to change belt and headlights.I could only find 1 screw on the bottom plate none on top plate. Thanks N J

There are two screws on the Fantom Thunder (It was not made by Eureka though) on the back of the unit just above the rear wheels. Remove these two screws and the top cover can be removed to get to the brushroll, belt and headlights. I believe the lig ... Vacuums

Need to replace a vacuum belt on a eureka model 4377. I cannot figure out how to remove the bottom portion to get to it.

Here is a link to the manual and a link to the belt you need:Eureka 4377 Replacement Belt ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

My Eureka model 2961 does not **** up larger particles. You can see it picks up dust and dirt. Am trying to remove bottom guard plate to check belt but can't take it off.

Here\015\012 is a Link to one of my Tips:www.fixya.com/support/r6311178-vacuum_brush_bar_not_spinningThis\015\012 should solve the problem. ... Eureka 2961AVZ Bagless Upright Vacuum


This must be a Savvy, Take off the plate covering the brush roll, then take out 2 screws from the bottom, turn it over, remove the Hoover emblem, there is another ***** there. Then the top cover will come off. ... Vacuums

How to remove cover on Kenmore canister vacuum model 116 in order to change belt?

... Kenmore 35912 / 35913 Progressive Upright Vacuum

Help hi i have a eureka bravo model #9270 and i need instructions how to change the belt, i took out twoscrews it looks like the top comes off but it doesn't come off all the way.

The handle should be down and the top may have a tab on both sides to pry out with screwdriver. lay handle down and turn machine over. look closely around base between cover and there should be a tab to push on and cover comes off. ... Eureka Vacuums

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?

First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

I have a Sears Upright vacuum cleaner, model 116.35922500. The vacuum wasn't picking up. I discovered a clog in the nozzle hose. I attempted to remove the cover of the brush unit to clear the clog. I was unable to remove the cover completely, but was able to clear the clog. My problem now is that I cannot replace the cover correctly. Is there a way to remove this cover? Thanks, Elizabeth

When you tried to remove the cover did you have to put a little force on it to get to the clog ... Vacuums

OUR DYSON 07 SWEEPER HAS VERY LITTLE Vacuum, have cleaned all filters and hoses, on line troubleshooting has said to check soleplate being on correctly, we have done this, still does not have good vacuum, belts are covered by a housing, the video that shows the changing of the belt is not the same, I need to know how to remove the cover to check both belts and any help in gaining the vacuum

This video shows you everything you need to know ... Vacuums

I need to remove the top cover from a Wertheim w4030, I have removed all screws that I can get at. I have notice a further 3 in places that is not possible to access. It looks as though the two buttons on the top if removed will provide the solution but I don't want to break anything by forcing something that is not supposed to be done. Can you help?

... Vacuums

Hey i have a eureka 2971 BVZ upright vacuum cleaner and after removing the old belt to replace it. I accidently removed the Guard Belt and i can't remember how to put it back on.

... Eureka 2961AVZ Bagless Upright Vacuum

I have the Miele S7280...the one without the clog hatch on the back. I took the bag cover off, then continued the remove the screws and cover underneath it to detatch the top from the bottom. Found the clog and cleaned it out. Heres the problem...now the power nozzle light comes on and the vacuum "on" is lite up red, but it will not come on. Checked the filters and the bag. It certaintly seems like the top and bottom are meeting up to latch into each other, but I have no power. Help!!

... Miele S7210 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0775 seconds