Having problems with your Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue ?

I have a model 6100 healthy home vacum. When it's turn on the motor make a very loud noise. I took it apart and blew some dust out of it. And it still make the noise.


Answers :

Hi,
\015\012Usually when a vacuum is making the loud noise it is because of a stoppage somewhere in the vacuum.
\015\012To find the blockage some detective work will be needed.
\015\012First off take off the hose at the closest point to where in enters the cannister or bag. This will tell you if the hose or the floor unit is plugged up. If the noise changes and goes away then you have a blockage in the hoses or floor unit and need to pull everything apart and clean it out.
\015\012To clean out the hose you will need a stick like a broom handle to push completely through the hose.
\015\012The floor unit may need to be taken apart to find the blockage. Often there are few screws in the top or bottom that hold it together.
\015\012
\015\012If removing the hose from the unit does not work then you will need to use your manual to find and clean all filters and check all of the passageways in the vacuum it's self...
\015\012
\015\012By checking all of these things you should be back vacuuming again...
\015\012
\015\012

Here is a tip that I wrote about my Bissel but I bet you have the same problem and the hose is clogged...

Bissell Bagless Upright Vacuum not working

heatman101

Repair Help & Product Troubleshooting for Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a model 6100 healthy home vacum. When it's turn on the motor make a very loud noise. I took it apart and blew some dust out of it. And it still make the noise.


Hi,\015\012Usually when a vacuum is making the loud noise it is because of a stoppage somewhere in the vacuum.\015\012To find the blockage some detective work will be needed.\015\012First off take off the hose at the closest point t ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi


Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums

I have a Hoover WindTunnel Bagless Vacuum Cleaner, Model #U5753-900, Serial number 110600215585, which I purchased from Loew's on 3/31/07. With it, came a Hoove Slider for hard floor surfaces, Model #S2105, Serial number 050500084989. The Slider strted making a noise--I thought something had been caught in the roller, but discovered, it had not; so I and my husband proceeded to take the Slider apart. I believe one of the belts had come off; but when we took the screws off the bottom to check


... Vacuums

I cleaned the roller on my Dyson DC 07, and after reassembly, it makes a sound like the belt is being chewed. I took it apart a couple times, goes back together fine, but still makes the noise


Hi its Darran at Dyson. \012\012Your machine is designed to make this ratchet noise if the brush bar is \012obstructed. We would recommend checking the brush bar and soleplate \012area and removing any blockages or hairs/threads that are ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Hoover Elite model # UH30010 is making very loud noise like it is going to explode. I took it apart as best as I could. There was a lot of dirt by the roller. Could not see what was causing the back up or why the noise. Any suggestions?


... Hoover UH30010COM Bagged Vacuum

Have a rexair model D series vacuum cleaner that worked fine until recently. Started making noise and then started smoking/overheating. I took apart the machine cover and am unsure how to get it tore down to see the motor or belt in there. Please help!


Below I have listed a link to the manual that has instructions on how to change your belt and a link for the replacement belt you need. ... Vacuums

I have a Dirt Devil Featherlite Model 085430. It making a horrible noise and I want to open it up to see if anything is broken or lodged in the motor housing. I've removed all the screws I can find and still can't get the thing apart.


Hi,\015\012\015\012The user manuals in this site may be helpful.\015\012\015\012Best wishes. ... Vacuums

I have a similar problem as many do with this model, "clean Roomba's brushes".. We took it apart last night, cleaned out all of the dust we saw. we removed the cover, the housing for the brushes and everything else we could. Still has the same problem. What now?


Mine did the same thing and no mater how much I cleaned the brush or pulled fibers of the ends it did not stop until I:Removed the little yellow tabs on the ends of both brushes and used a tooth pic to remove the built up inside the bearing ass ... iRobot Roomba 530 Robotic Vacuum

Electrolux Hi-light Hi, my hoover is making a weird knocking noise and emitting a burning smell. Took the lid off and the belt *seems* okay, but still makes the noise and the smell....


Burnt smell is probably the belt slipping. Even though it looks OK, either the belt needs replacement and/or the roller needs cleaning and/or lubrication at the ends. Try cleaning the roller ends first and then light lubrication with WD40. If belt ... Electrolux Central Vacuum

My Model number 11635923502 kenmore vacuum is making a deep suctioning noise as if something is stuck in it. We have cleaned out the filters and all the vacuum lines thinking it was clogged. It is still making this noise and we are frustrated as to what could be causing this problem. The unit does not have much suction.


... Kenmore Progressive Upright Vacuum with InteliClean System Slate Blue

HORRID NOISE I have took it all apart and thoroughly cleaned it. It is still picking up dirt etc. But the noise sounds like its taking off. It is not that old so can not be the engine my mother has one that she has had much longer and is fine she has also checked it it is out of guarantee but is working the noise is terrible. Can you help???


Hitake out the belt and brush. Switch on. If the noise has gone you know its the brush. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Kenmore upright vac model 33922 - good suction but developed loud whining noise after accidentally vacuuming room without bag. Added bag and changed both filters. Still makes noise. How can I stop noise?


The bag is the first stage in your filtration. Most times what you did will draw fine dust right through the filters and into the motor itself, affecting the bearings and clogging the motor fans, throwing them off balance. The fact that there i ... Kenmore 33922 Direct Drive Bagged Upright Vacuum

My FEIN 9-55-'13 recently started making more noise and is now officially a "screamer". There also developed quite a vibration associated with the noise which made me think it was probably bearings. So I took it apart and found no detectable play or lateral movement in the bearings, they seem fine to me. So I thought perhaps the brushes. The rotor where the brushes ride is quite black but I can't figure out how to get to those brushes, although I don't really think they are causing the noise


This problem is only caused by one thing the motor bearings are noisy, I have never found any other reason, they may look good and fell good but trust me replace the motor and the noise ... Fein 9-55-13 Turbo II Bagged Canister Vacuum

Miele vacuum Sometimes when I hit the auto roll up cord button or even move the cord, the power vacuum goes off. I move the cord again and it comes back on. I took it apart and looked at the connection from the cord to the auto roller. These are the electrical slip on type connections and are still in good shape. There are no bends in the cord. I air dusted everthing inside, put it together (with no extra parts!). Good news..it powered up so I did not break it, but it still has the same problem.


... Vacuums

MY HOOVER VACCUM MODEL #U5185-900 IS MAKING A LOUD VIBRATING NOISE AND I CANT FIX IT, IT STILL PICKS UP STUFF BUT THE NOISE IS UNBEARABLE. cAN YOU HELP ME


T could be 1 of 3 things:1. The belt that drives the beater bar. ... Vacuums

Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall


That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums

My Kirby 2HD has started making an odd roaring noise but still works fine. I have taken the front assembly off and cleaned and adjusted the roller and checked the belt. The noise seems to come from the motor housing. I have tried to wiggle the main shaft at the front (bearings?) and it seems tight. Can't seem to get the other housings apart. Any ideas? Thanks, John


It is quite possible, it just needs lubed. The motor comes in direct contact with dirt so, you have to make sure the front bearing has a drop of oil on it from time to time. If it starts to scream at you within one month, after oiling, the bearing ... Kirby Heritage II Vacuum

My whirlwind Eureka model 5197 is making a very loud noise yet the suction is still okay. Any suggestions? Could it be the belt slipping? It's a self propelled model.


... Eureka Whirlwind 4496 Bagless Upright Cyclonic Vacuum

I bought the Eureka 4703D model vacuum and my very first time powering it on, it was extremely loud - abnormally loud, and I don't know if it is loud like that because I possibly put it together wrong, or there is something wrong with it or it was previously damaged and I would like to know if this is something I can fix myself or do I have to take it back apart and return it to Walmart where I purchased it from. When it makes the loud noise, it does vacuum fine but the noise is just unbearable


... Eureka Power Plus 4703D Bagless Upright Vacuum

Roomba 550 I have a similar problem with my 550. It gives me 9 beeps and oh-oh. Took it apart, lots of junk got inside where the modules are underneath the gears. Don't know why. Blew it out with compressed air. Still no luck. Someone on YouTube made a video. Check it out if you have time. http://www.youtube.com/watch?v=s2Ts9oMs7J0&feature=related


Nice video on how to clean the CHM\015\012\015\0129 beeps suggest a bumper fault\015\012You are probably facing a bumper sensor issue.Try to clean the bumper first and if this goes on, either call iRo ... Roomba Robotic Floor Bagless Vacuum

Hoover model U3490 makes a high pitched squealing noise when turned on but it still works brilliantly . I have rerplaced all the filters and bag. It sounds as though air is escaping. If anyone can help I will be very grateful.


... Vacuums

Our Dyson sucked something up last week (not sure WHAT) and now the telescoping hose won't ****. Well, it sucks but just BARELY . I took the hose apart and can't see anything, but it makes a weird noise now when you stand the unit up and are not actually vacuuming with it. Help!


Well if the hose is completly clear the blockage is either before that or after that the brush roller should come out to clean the tube as you know also comes out make sure all are clear right up to the collector ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

TOOK MY ELECTROLUX EPIC 6500 CANISTER MODEL 1762 APART TO REPLACE CORD REWINDER. TO MAKE A LONG STORY SHORT,MOST OF THE WIRES CAMES OFF OF HEIR CONNECTIONS. NOW CAN'T FIGURE OUT WHERE THEY GO WITHOUT A SCHMATIC. CAN ANYBODY HELP. THANKS CATHY


Hi,\015\012\015\012I will try to find a service manual for you. ... Vacuums

My vacuum's cyclonic action is not spinning and creating very little vacuum pressure through hose or floor brush area. I already checked, brushes are spinning, there is no apparent blockage in the canister, I took it completely apart and removed excess dust from the filter. Still no good vacuum. Any suggestions?


The following filter in your in your dump cup needs to be replaced. \015\012F24 Dirt Devil "I" Bagless Upright Vacuum Replacement Filter Style F24 ... Dirt Devil M130005 Bagless Upright Cyclonic Vacuum

I bought this vaccuum just a few months ago. Now it barely sucks anything up and it is making this very loud noise. It almost sounds like the brush is going to vibrate off. I keep thinking something is stuck in it, but I took it apart and everything seems normal. It did melt a couple of belts also.


Probably the motor is jammed or the part where it sucks up stuff its full ... Bissell 3590 CleanView Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0935 seconds