Having problems with your Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue ?
Our beater brush makes a really loud grinding sound when turned on.
Clearly something is jammed in up under the beater brush... if not there, then follow the belt which drives it.. something is caught up for sure.
Repair Help & Product Troubleshooting for Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Our beater brush makes a really loud grinding sound when turned on.
Clearly something is jammed in up under the beater brush... if not there, then follow the belt which drives it.. something is caught up for sure.Ck ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue
When I vacuum w/ the brush control in the on position it make a really loud noise, almost like a grinding sound. I have looked at it and nothing seems to be wrong, but I notice that the pin that engages the belt seems to vibrate a bit, possibly creating the noise. It started when I accidentally got part of a plastic grocery bag caught in the brush. Could it have stretched a belt? Nothing is caught any other place and it only makes the noise when the brush in in the on position.
Yes, the belt could have been stretched and is now vibrating and hitting other parts and creating a noise if much of the bag got caught under the belt. If you have another belt for this vacuum, please put it on and see if the noise stops. If it does ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum
I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.
... Windsor VS14 Versamatic Bagged Upright Vacuum
I replaced the belt on my Dirt Devil Featherlite Bagless Vacuum and the brush roller rubs and makes a very loud noise when turned on. I have gone exactly by the manual instructions and made sure the belt and end caps were on correctly, but the bristles still rub the back and it makes a very loud noise. Without the brush roller in the vacuum, it sounds and runs normal. What could the problem be?
Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=561283\015\012Generic problem for all Vacuums\015\012I replaced the belt on\015\012Posted by piggyt ... Vacuums
I have a Kenmore canister model 116.25812 that makes a very loud beating noise when the powermate is turned on. I replaced the belt, but still has the sound. Also replaced the bag and both filters. Suction is great, but is very loud when the brushes turn.
DYSON DC14 While vacuuming the living room, the rotating brush started making an awful loud grinding sound. We opened the intake port, cleaned the brush but to no avail sound still persists once you lower the vacuum handle in an attempt to clean. Was wondering if there was anything that can be done?
Take the bottom plate off and check the belt. Also, rotate the brush by hand - it should turn with only a moderate resistance from the belt, or very little if you take the belt off. If it is hard to turn, or if the belt is stripped-out right where it ... Vacuums
Loud rotating carpet brush noise: Just got my new Shark Navigator, but it makes a really loud noise when I turn it in the position to clean carpets. Is this normal?
... Shark Navigator Bagless Upright Vacuum
Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o
Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum
Dyson DC04 is making a grinding sound & smells of burning. Hi. I have been told that the above is due to the carbon motor brushes burning out. The brush at the bottom still turns ok. I have bought 2 new carbon brushes & wondered how I would go about replacing them. Any help would be much apprecieated!
Hi there SmartAlec from NelsonVacuums.com.au here, this is not a repair for the faint hearted. First i am assuming you are not using a clutch model - with a selector for ca ... Vacuums
My vacuum cleaner is making a loud squealing sound when I turn it on and the brush is turning. It gets louder while vacuuming the carpet. I tried to remove the bottom cover to see inside but, took out a bunch of screws and couldn't get the cover off.
... Kenmore Progressive Direct Drive 30912 Vacuum
Vibrating When I turn on the vacuum , the bottom where the brush is vibrates to make a loud sound. I cleaned the brush and took the gray plate off. when replaced made louder.
I misunderstood the original suggestion to fix this issue. It was a misalignment on the beater bar. I fixed that and voila! Vacuum is perfect again. Thank you ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Hello. I took the sole plate of to clean the brushes on my dyson dc14 however the brush part came out and i put it back in but since then whenever i switch it over to carpet setting it makes this really horrible clicking grinding sound its only new have only used it a couple of times.
You really need to take the sole plate back off and make sure the belt is running exactly where it's supposed to go and not looped over a piece of plastic or anything. More important is that you make sure the ends of the brush are seated properly an ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
I have had my Bissell Healthy Home for just over a year. I use it once or twice a week on five area rugs and two small bedrooms with wall to wall carpet. Just recently, the motor started to sound extremely loud and it smells like it's burning. The vacuum still picks up everything and all the brushes are turning. Advice? I really like this vacuum and would really like to fix it rather than replace it!
Hi,Here is a tip that I wrote about my Bissel but I bet you have the same problem and the hose is clogged...Bissell Bagless Upright Vacuum no ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum
Pfaff Creative 1459. When trying to wind a bobbin, I do what I've always done, turn the small round "wheel" on the right, slide the bobbing into the little knob that keeps it in place and gently press the foot thing on the floor that should start the bobbing to winding. The bobbin does not turn at all causing a loud whirring sound and the needle goes up and down as if it were making stitches. I finally got some thread onto the bobbin but it is not smooth and looks like a spider. I really nee
Beater bar not turning, making loud sound - Dyson DC07 Bagless Upright Cyclonic Vacuum
This machine has a clutch assy. that slips and makes a loud noise\015\012when something gets stuck in the roller brush. If you have nothing stuck in the roller brush chances are the clutch is worn and needs\015\012replacing. Not an easy ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Beater bar rotating but now making really loud almost buzzing sound???
It is probably a bad belt.That model uses a geared belt and you possibly have a few teeth missing on the belt.It could also be a bad brush or bad motor but less likley.Take the cover off of the power nozzle and inspect the belt.Disconnect it and look ... Kenmore 25512/ 25513 Progressive Canister Vacuum
My Bissell series 65832 vacuum's rotating floor brush is making a really loud noise like its hitting something when ever I turn it on. Can you tell me how I can fix .
It probably needs a new belt, unplug the unit and find the screws that hold the cover where the belt it,remove them and look at the belt.Or it could have string or something wrapped around the brushes that would need to be cut out. ... Vacuums
Had my dyson root cyclone for about 4 years now, and in the last year it's had a few problems. About 4 months ago it started to make this awful grinding sound when the roller bar was engaged and I took it to a repair shop and they said it was the roller bar itself. The shop replaced the part and it worked fine for a couple of months and then it started to make the grinding noise again. I tried the clutch reset suggestion (turn it on its side and turn the carpet/bare floor switch slowly back and
Bdepends how much thay charged you for a roller brush because you can buy a good vac for about 100 pounds with a 12 month guarentee so its up to you ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Loud noise I have a brand new Dyson and it is great on all my floors except one of my area rugs when it starts making this really loud vibrating noise. I am not sure why - nothing is stuck in the roller or vacuum and it doesn't make it on any of my other rugs. Also it is really hard to push whereas all the other floors it just glides. I don't want to return it but I also don't want to hear this sound every time I vacuum.
This is the clutch as it jams up in the brush. Usually happens with rugs that are not secured to the floor. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
My bissell 82h1 has developed a very loud clattering noise. I cleaned the brushes and checked everything I could easily access to no avail. When I turn it on with the brush removed, the sound level is normal. With the brush in place, I can easily turn it by hand with no indication of it hitting anything.
... Bissell 82H1 Cleanview Helix Bagless Upright Vacuum
My brush roller stopped spinning so I had to take it off and clean out all the hair that had gotten wound around it. I replaces it and now it is make a lound noise, but only when the brush is on. Could it be the belt making such a loud sound? It wasn't making this noise before.
Could very well be the belt.\015\012When cleaning the brush it is a good idea to add some WD40 at the ends where the plastic pieces are that hold the brush in the vacuum. The brush needs to be able to move freely around the plastic pieces.\015\012Ad ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum
My Oreck xl makes really loud sound and starts to smell hot when running still picks up but I am afraid I will damage something if I use it. The loud sounds gets very loud then quits for a few seconds then starts again.
... Oreck XL Ultra Bagged Upright Vacuum
I have a Dyson DC17 that has started making a loud noise when on carpet when the brush is engaged but not on hard wood when the brush is not turning. I have remove all the material (hair,lint, etc.) wrapped around the brush itself, but it is still making the noise
You need to replace the belt. Here is the belt you need and a manual you can view which has instructions:\015\012\015\012Dyson DC17 Belt and Manual ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Brush bar does not turn & makes a loud noise
You need to clean your roller and replace the clutch assembly that drives the belts. poorly designed vacuum with many flaws. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Ratchet noise, beater will not turn, belt not broken, in carpet mode the Dyson d07 makes huge ratchet noise and the belt will not turn the beater brush.
Ok, so I had the same ratching noise and took the advice of many sites directing me to clean the brush. But like most I cleaned the brush and the noise continues and the brush does not spin. Reluctant to take it to get serviced I dug a l ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum