Having problems with your Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum ?

Pump belt on bissell scrubber

\015 I have bought a belt for my scrubber, I know where it goes, but do not know how to get the pump off to put the belt on. help me\015

Answers :

If this is a Bissell Pro-Heat, then first take the belt cover off, it is on the left side on top of the noozle. Then turn it over, take out the one screw from the red lock, pull it off, then remove the cogged belt, take out the old pump belt if still on from underneath. Put a new one over the pump end, then feed it thru the opening and put it over the motor shaft. Put it all back together.
Repair Help & Product Troubleshooting for Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Pump belt on bissell scrubber


If this is a Bissell Pro-Heat, then first take the belt cover off, it is on the left side on top of the noozle. Then turn it over, take out the one screw from the red lock, pull it off, then remove the cogged belt, take out the old pump belt if stil ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there's two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it's a ribbed belt? that is the water pump belt?


Just taken ours apart with the same problem... found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places - the bottom of th ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I have a bissell proheat carpet cleaner purchased in 4-18-2005 for $169.99 from kohls I have used it 6 times and the last time the brushes would not move cause the belt was broken and the end of the pump pulley which is plastic broke off so I reorder the pump unit and 2 new belts and now I see you have sent me a exact pump but the end that broke off that the belt rides on is made of steel or aluminum much strong piece of equipment I want to know if there was a recall for the machine due to mecha


I've owned my Bissell for over 5 years now & LOVE it! Even after vacuuming It pulls up tons of dog hair I never realized was there! I am having a similar problem, but I caused it myself & think maybe you may have the same problem, cross you ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Bissell 1697w I just got the bissell 1697 steamer and I had to replace the pump belt. I can not figure out how to change the belt.


First take off the belt cover on the side,\015\012then turn it over, on the belt end of the brush roll, there is a red piece to hold in the brush roll, take out that screw and pull it off, the you can remove the end cap and cogged belt, Put th ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Search for bissell pro heat pump. bissell.com will not have it ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Pump part number is 2107181, the diverter valve # 2136988. You can Bissell and they can tell you who may have parts near you, or you maybe able to order thru Bissell.com. Before you took it apart, were you getting water to spray out of the hose. I ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a


... Bissell ProHeat Deep Cleaner Upright Vacuum

There is a shaft that comes out of the pump of my Bissell 1623-1 Power Steamer with gears on it. The belt to the brush attaches to it. When I went to change the belt, the belt was fine but the gear itself with the small shaft on it was no longer attached and just dropped out. It looks like there might have been a bushing there, but no more. Any ideas?


... Bissell Vacuums

Bissell Proheat Clearview - Belt and pump keep melting


Is the brush roll turning freely? Is there something binding the pump pulley or belt casuing it to not turn? Was the replacement pump a new one? If you replace these parts again, after doing so, try turning the pump pulley by hand to see if it wil ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

How do I replace a pump belt for my Bissell 8910


This link is a video of belt change for the bissell proheat. ... Bissell 8910 ProHeat Clear View Upright Vacuum

Replacing the Brush and Pump belt on Bissel Steam Cleaner 1901


... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I have a broken pump belt on my bissell powersteamer proheat. The belt was just laying in there. I have a new one but no where in the manual does it tell you how to replace it and where! Help


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1698-1 PowerSteamer ProHeat Plus Upright Vacuum

How to change pump belt on bissell pro heat - Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum


First take off the cover on the left side oif the top cover, then turn it over, remove the screw holding the red lock and pull the cap and brush roll out, remove the cap, remove the cogged belt, then you can put the new pump belt thru that slot, put ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

I have a Bissell Model 8905 Carpet Cleaner. I was going to replace the belts because the pump belt broke, but when I turned the machine over, a small piece fell out. It looks like a tensioner arm because it has a small round part at each end on opposite sides of an arm that has an offset or "dogleg" in it. I am looking for an exploded parts diagram to determine what the part is and where it came from.


... Bissell 8910 ProHeat Clear View Upright Vacuum

I have a bissell 1698 powersteamer. i have already cleaned heater and completely cleaned all parts , checked the mix piston, checked belt. it will not shoot water or mix. the motor runs, it will **** water and the brush turns. is it the pump and does the pump just shoot the soap?


Pump is probably bad. When you put the lid back down, did you put the piston on the bottom of the smart mix knob? Also the smart mix knob should be in the water only selection when the top is pushed all of the way down. Also sometimes the flow ind ... Vacuums

Belt manual need to know how to put on a pump belt on a 8910 bissel proheat


Here is the manual. on page 17 tells you how to change.\015\012\015\012http://dl.owneriq.net/2/23cae7f7-686f-47c1-8efe-3a106fffcd50 ... Bissell 8910 ProHeat Clear View Upright Vacuum

My bissell proheat pump belt....


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

Need help installing a pump belt on my bissel steam cleaner


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Instructions to replace pump belt on model 37E3 bex bissell


... Bissell Vacuums

My bissell power steamerr 1697-w won't dispense water, pump belt o.k. what else couuld it be


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Trying to replace pump belt on bissell cleaner


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Bissell 7950 ProHeat Self Propelled Carpet cleaner Replacement Pump Belt part 215-0628


Normally, there is a post sticking out of the retainer to remove it. If the post is broken off, then you will have to lift the black arm and wiggle it at the same time and the retainer will pop up so you can remove it. On the belt side, the retainer ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

We have bissell pro heat and I have put new belts on and took off the top plastic cover I blew out the lines and I still can't get it to pump water or solution. The red little spinner flow indicater does'nt get water, if I pour water into it it runs out the front. I guess I don't know what else to do. The machine worked fine the last time we used it about 6 months ago. Any suggesttions?


Did you check and make sure the belt is still on right? They do come off from time to time.There are like 6 long screws holding the top cover to the bottom. The are real pain in the behind to put back together once you take them off. T ... Bissell Vacuums

Nothing spraying out of Bissell Powersteamer Proheat. I've check filter under flow indicator, pump belt is fine, cleaner in proper tank, bladder of water tank is full. We've had it for a very long time but it's barely been used. Can anyone help?


... Bissell 1698-1 PowerSteamer ProHeat Plus Upright Vacuum

Bissell Pro-Heat 7901-1 no cleaning solution is pumped out. The flow indicator is spinning and the belt is spinning the beater bar. Have cleaned the flow indicator, checked vavles in the solution tank and water tank and they are working properly. Also checked the trigger to make sure it works okay. Any ideas?? Moody Fan


Bissell Pro Heat shampooer - Fill the soap dispenser with extremely hot water and shampoo with only water for a few minutes. There is often dried soap in the lines. Make sure that all filters are clean. Press the soap container and the water conta ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0597 seconds