Having problems with your Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum ?

My brush on my vacum will not spin. Belt is not broken

Answers :

Get a dyson or a dirt devil
Repair Help & Product Troubleshooting for Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My brush on my vacum will not spin. Belt is not broken

Get a dyson or a dirt devil ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Miele White Star SEB 204, powerhead stopped spinning. brushes are clear of debris, belt (#3854940) is not broken. Could belt be stretched so that brush head does not spin?

Yes, most likely the belt has stretch. Flat belts do this after a short time and need to be replaced when problems start with the brush roll not wanting to turn. Also check the brush roll, make sure that the ends turn freely, if not, then replace i ... Miele Vacuums

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.

You need a new belt. ... Vacuums

Brushes wotn spin,belt not broken,cog that drives the belt is not spinning.When I turn the brushes manually I can occaisionally feel it grabbing for a a brief second.Could the motor be bad? Is there a way to test the motor.Tahnks

The motor is bad and this is a common problem with this machine. It is engineered very poorly. I would take it back and get a Dirt Devil Platinum Force machine. They have a great track record. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

We have the Bissell Lift off Revolution vacuum. The brush roll and belt are broken. The brush roll has seized up and no longer spins which caused the belt to burn out. How much is a replacement part cost? Debie [email protected]

You can get the belts for that model here: http://vacbelts.xps.convina.com/bissell-style-8-belt.htmThey are only 4.99 for a 2 pack. Plus they ... Vacuums

Brushes are not spinning. think the belt is off or broken. how do i access the belt?

There is no belt in this machine. The brushes are turning by an air driven turbine. The turbine has a pivot bushing made of steel inside of it that gets rusty because of the water that is running through it. The turbine will have to be replaced an ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Kirby sentria My roller brush won't spin belt is not broken I cleaned the Roller brush and put it back it. It put it back but it looks like the sensor balls aren't touching the plastic part underneath. The green light Doesn't turn on either. It was just working and it stop picking up out of nowhere this

... Vacuums

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

Vacume brush won't turn but belt is not broken

The belt is probably stretched and won't drive the brush roll. Also check the brush roll, the ends should turn freely, if no, then replace it also. ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

I have a eureka 4351 and I think the belt is broken but I can't figure out how to access it to check. Roller brush doesn't spin though. Just need to get the silly thing apart.

... Vacuums

My Kenmore canister model (116) 26212601 works in hard-surface mode (basic suction), but the brush won't spin for carpets, and when I try to turn it on, it makes a whiny sound and then turns off as it does when I need to press the overload button. I looked inside a bit, and the belt isn't broken--it seems fine. So not sure what the problem is. Thanks for any help.

... Kenmore 27815 Bagged Canister Vacuum

Why are the brushes not spinning? The belt is not broken.

Remove the belt and check if you can turn the brushes by hand. They may be jammed up with something in which case remove unscrew clean and reassemble.If the brushes are turning but the belt isn't report back. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a bissell momentum ive broken 2 belts the brush doesnt seem to be spinning they are placed into the side slots correctly what could be the problem?

Most likely your brush needs to be removed and cleaned.\015\012Clean all debris that might be in the bristles of the brush. You will see a holder for the brush on each end that holds it into the frame of the vacuum. The two holders should turn free ... Bissell Vacuum - Momentum Cyclonic 1 ea Bagless Upright Vacuum

Smell/suction I have a Eureka Altima Model 2991 Type AVZ. I have suction when I use the power paw and attachments. I have all hoses clear. My brush is spinning and belt is not broken (I opened it up and checked), but I have no suction when I turn it on to vacuum my living room carpet. I also have a burning smell to go with it after about 30 seconds. I've never had a problem with this vacuum cleaner before.

Ours started smelling too, and it seems that the plastic end on the roller brush was melting. In process of finding rollerbrush for it now ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum


If the belt that drives the brush is not broken, check to see if the brush itself is stuck from turning.\015\012If is is, remove it and clean as best you can, paying special attention to the two ends. It might make sense to spray the hard rubber hol ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

We have a Dyson DC28. The brush no longer turns while vacumming the carpets. Also, the lights on the handle to adjust for different heights do not work. Can you help. I see of no way to get to the belt but I don't think it is broken.

Hi there,I'm sorry to hear you're having difficulties with your DC28. It's probably best if you get in touch with us directly so we can resolve this issue for you as quickly as possible. If a repair is necessary, this should be covered by our ... Dyson DC28 Animal Bagless Upright Vacuum

Belt not broken but brushes not spinning - picks up hair but not small particles

Belt not broren but brushes not spinning ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My brush stopped spinning and there are no clogs and the belts are not broken any suggestions?

This depends on witch company vacuum you have\015\012you may have a switch or motor to drive the brush ... Vacuums

Brush stopped spinning from fabric being sucked into it, how can I fix it? It's a Dyson animal vacum. The belt is not moving from the lower motor.

Turn upsidedown.\015\012There should be 3 plastic screws in a triangle shape.\015\012Loosen, but do not attempt to remove the screws.\015\012This will release a shield that will expose the brushes.\015\012Carefully remove the ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Brushes will not spin, is there a belt that may have broken?

Hi There,\015\012\015\012I did a tip and trick with this exact solution. The below link will help you diagnosis the problem, and explain how to fix the problem whatever it si. \015\012\015\012HOpefully this helps you,\ ... Hoover V1 SteamVac SpinScrub Vacuum

My belt is not broken and the brush is not spinning or sucking. Only have suction through the hose.

The ends of brush may be stuck. The bearing may have hair built up in them ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The brush doesn't spin anymore, but the belt is not broken. model DC 07; approx three years old

The belt may not be broken but after 3 years the belt will have stretched and it will not turn the brush. You should change the belt every year. Changing the belt is an inexpensive fix. I would try that first and if it doesn't do the trick I would ta ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a

... Bissell ProHeat Deep Cleaner Upright Vacuum

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge

... Vacuums

My floor brush stopped spinning, I cleaned everything out as per your directions in other posts and following the instructions in the manual. Now the floor brush wobbles and has a hard time spinning when upright. Looking at the end of the brush, opposite the drive belt, the bearing-type end that the brush spins on appears to be off-centered. Is there an easy way to fix this???

... Bissell 3130 Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0561 seconds