Having problems with your Bissell Powersteamer 1694 Upright Vacuum ?
Will not let any water out when i squeeze the water trigger.
Try squeezing the trigger a few times repeatdly. This usually works for me.
Repair Help & Product Troubleshooting for Bissell Powersteamer 1694 Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Will not let any water out when i squeeze the water trigger.
Try squeezing the trigger a few times repeatdly. This usually works for me. ... Bissell Powersteamer 1694 Upright Vacuum
I have a Bissell Proheat 2XTurbo carpet cleaner. No water will come out when I squeeze the trigger. I have filled the solution tank and the water tank. I read the troubleshooting in the manual and have tried turning it off for a minute and restarting and nothing. I took out both tanks and reseated them and nothing. It has sat for over a year but did not have any water in the water tank. Some solution was left in the solution tank. How can I make the water come out? HELP!
Call BISSELL Consumer Services.\015\0121-800-237-7691\015\012Mon-Fri: 8am to 10pm ET\015\012Sat: 9am to 8pm ET ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
Water is not being discharged. I have filled the reservoir that holds the carpet cleaner fluid And I have filled the water container. I know how to use the cleaner, it has always worked, But now, no water is being discharged to the carpet. I turn it on, squeeze the trigger, but nothing comes out. The wheel that is suppose to spin (to indicate that water is being discharged) is not spinning. Everything else works. I.e. the suction works, and the hand held accessories work.
That means that the pump belt is worn and it needs to be replaced. You can get a replacement belt and view the manual here:Bissell Pump ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
My Bissell Quicksteamer Model 1960-R won't spray cleaning solution. I have cleaned it and taken apart the whole thing. I can't find any problems. The holes are not cloged where the water comes out as I disconnected it and blew through it to be sure. The lines show water trying to go through. It is as if it doesn't have enough power to pump the water out when I squeeze the trigger. I am thinking it is the pump thing but can't find a replacement part for it.
... Bissell 1960-3 QuickSteamer Plus Upright Vacuum
Water comes out when trigger is squeeze but wont **** up dirty water
A. Is your floor/hose knob in the correct position?\015\012B. Do you have suction at the hose end, when in that position?\015\012C. If you answered yes, no in that order then either your motor (provides the suction) is going bad, or it si ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
I have a powersteamer and it does not spray water when I squeeze the trigger. The clean water tank is full, the cleaning solution is full and this is the same problem I had with my last Bissell steam cleaner, which I assumed was just that I had it for a few years, but this cleaner is only over a year old.
Every line has an O Ring at each end. inspect each one by removing the O Ring for nicks and cracks. Lubricate the with Vaseline and reinstall if ok so they will hold the prime to pump and vacuum up Your leaking O rings will draw air causing your p ... Bissell Vacuums
I have the Hoover max Extract 77 and when I'm cleaning the carpet, the clean water tank leaks on the floor, even if I'm not squeezing the trigger. The clean tank doesn't leak when I fill it, but once I place it where it fits and start using the vacuum, the clean water drains out on the floor. The dirty tank fills up, so the suction works, but, I don't know what is going on?
... Hoover Vacuums
The water in my vax rapide powerjet pro v-028 keeps emptying when I let the trigger go until the tank is empty
When I squeeze the trigger, water won't come out of my Bissell PROheat2X carpet cleaner. The beater bar rotaotes, and there seems to be suction. Nothing comes out the bottom.
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
Bissell ProHeat2x carpet shampooer does not dispense water when you squeeze the trigger
This can be one of 4 things the belt on the pump as waren (it may not seam ware but replace it if you can ) the water jets by the roller are bloked ( x2 red ) the pump as faled or this on about 2 in 10 the heter is bloged this hapens then the sope or ... Vacuums
Cleaning I cannot get the cleaner to release solution on carpet. have lost manual. is there a trick to this? I have tried squeezing trigger handle to dispense solution with no luck. have followed instructions (2 capfuls cleaner, fill with hot water to fill line) on filling tank.
Either you have a pinched or clogged water line, or the rod in the handle is pushing down like it should. The drw back is Bissell has deemed this unit and its parts obsolete. So any parts are hard to find.\015\012\015\012 ... Bissell 1950-3 Quicksteamer Plus Vacuum
My bissell will spray out of the hose, but no water or soap when i squeeze the trigger? The belt is turning the pump
See if your tank is seating properly. I bet it's sitting up a bit. Is there water in the little well where it sets? ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
No water dispenses from my hoover ultra steam vac model F5883-900 when the trigger is squeezed.
Remove the clean water tank and look in the opening just behind the black grommet. Operate the trigger - you should see the valve move downward as the trigger is pressed. If it is NOT moving, then you will need to have the trigger plunger shaft repa ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum
No water sprays out when you squeeze trigger - Bissell Vacuums
Generally this is because you didnt clean out the machine & so detergent dries in the jets & blocks them. Take apart clean & hey presto. next time rinse thoroughly when you finish & if you lend it someone dont believe they have rinsed ... Bissell Vacuums
For starters, the water in the resevoir doesn't come out when I squeeze the trigger.
There are some possibilities you will have to check out first\015\0121) is the tube connected to the ends from where the water comes out is loose or the tube is getting blocked .\015\0122)also check the motor gears which spins while you press the tri ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum
No Water My Bissell rug shampooer does not eject water or saop whan I pull the saop trigger on the handle. I checked both filters and they are clean. Then, I removed the container that sucks up the water and pulled the saop trigger, water barely came out of the tubes. I tried to clean the rug in our family room and the rug was not wet when I finished, no water coming out to clean the rug. HELP HELP HELP!!! I live in Colorado is there a Bissell repair shop near Denver, HELP!!! Thanks Dominick ema
Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be o ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
Steam doesn't come out anymore when I pull the trigger. I think the water in the tank is getting hot, but when I pull the trigger, only a little water comes out. No steam
Try putting some white vinegar in the tank to dissolve any hard water deposits. You should use only distilled water in this machine. Don't try to clean anything with the vinegar in it, but take it outside to run the vinegar through. ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
I got my bissell for $7.50 from a thrift store, if you can believe THAT. Used it for the first time today after reading the manual online first. After filling the clean water bladder full of hot water and setting everything up the way I wanted, proceeded to turn things on and go for it. Well, the water/solution just kept coming and coming, without my finger on the trigger. Obviously something is jammed in the open position but where? The trigger moves freely.
This is the answer I got from Bissell:Please\015\012check the gasket at the bottom of the tank to ensure it is attached and\015\012not lodged in the reservoir of the machine. If this is not the problem,\015\012take the machine for i ... Bissell 8910 ProHeat Clear View Upright Vacuum
I have a Model F7431-900 and is a SteamVac V2. When I press the trigger for water or cleaning solution, the water just runs right through it even after releasing the trigger. What kind of problem do I have? Is it most likely a valve problem? I'm handy at fixing things and want to avoid the large repair bill if I take it in.
This sounds like a stuck solenoid. The Dual V models use solenoids to contol soap and water flow to the floor, along with a pump unit. If your unit is 12 months or less it is under warranty. I am not sure about the cost of the solenoid. ... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum
I have a hoover f5861-900 steam vac. the trigger mechanism seem to not work anymore. Water dribbles out without using the trigger. Taking the water tank out I can see the rod very slightly moving on the diaphragm. I removed the top part of the vac to hopefully reset the rod connection. But, didn't make any difference. I appreciate any help you can give me. thanks
... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
My Eureka Atlantis Express is brand new - never used. I took it out of the box, read the manual, filled the soap and clean water tanks, put them in. I lifted the machine off the counter to take into the living room but all the water came running out of the bottom all over the kitchen floor. I can see where the little white plastic piece sticks up into the water release valve and lets the water out. How do you stop this? Can it be fixed?
... Eureka 2553A Atlantis Handheld Wet/Dry Vacuum
I have a hoover power scrub steamvac, the main soap dispenser trigger on the handle click when pressed and does not work (broken spring??) the other soap triggers on the hose and the trigger on top to dispense extra water both work. Can I fix the main trigger myself?
When squeezing trigger and Depressing Clean surge Button on Upper handle of the Hooover Steam Cleaner F5914-900 there is no "snap" indicating trigger rod is in place. Everything else went in as instructed. The screws and bolts were no problem this concerns me because the main complaint I read about this model was leaking from the trigger and clean surge and the problem was not getting the rod in place. No matter how many tries or people (three) it still doesn't occur.
Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=552215\015\012Generic problem for all Vacuums\015\012When squeezing trigger and Depressing\015\012P ... Vacuums
I have a hand held vaporettino steam cleaner ....the appliance is working but the water container has been dropped and has a hair line crack in the base and leaks the water from the crack ....I am looking to either buy a replacement water container or to buy a new S/Cleaner if you could let me know of a supplier either in the UK or Spain
... Polti Vacuums
My HAAN Garment steamer was only intermittently releasing steam. I cleaned it out since there was some mineral deposits in there. After cleaning it out, I let it run for a while with distilled water and the same thing was happening. So, I called HAAN and they told me to troubleshoot. This entailed taking all the water out of the system and "shaking it out." Then to put new water in and turn it on. I was to do this three times and call them if it didn't work. After the third time, I realiz