Having problems with your Bissell Powersteamer 1694 Upright Vacuum ?

Bissell powersteamer powerbrush starts up and then i pull the triger and water starts then stops. i cleaned the bottom of the tank by taking it apart and even had a different tank and both of them did not work. changed belts???


Answers :

Tried to find out about this problem, and ran across this recall on the net:
\015\012http://www.consumeraffairs.com/recalls04/2005/bissell.html
\015\012This recall applies to your model, so maybe you can get your money back or get another unit. Good luck, and hope this helps.
Hello,

Select the setting on the outside of the formula tank. The choices are \015\012"high traffic," "normal" and "water rinse." The steamer will mix the \015\012appropriate amount of formula with the water in the tank. Choose the \015\012"floor cleaning" setting on the tools dial that's located to the left of\015\012 the tank. Plug the steamer into an electrical outlet. The power switch \015\012is on the back of the machine handle; turn it to "on. if no improvement, check to ensure the openings are not stuck with debris, also, check the cord to see that it is not bad, if it is, replace the cord.

Take care.
\015\012


\015\012

Repair Help & Product Troubleshooting for Bissell Powersteamer 1694 Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bissell powersteamer powerbrush starts up and then i pull the triger and water starts then stops. i cleaned the bottom of the tank by taking it apart and even had a different tank and both of them did not work. changed belts???


Tried to find out about this problem, and ran across this recall on the net:\015\012http://www.consumeraffairs.com/recalls04/2005/bissell.html ... Bissell Powersteamer 1694 Upright Vacuum

I just used my Bissell Proheat, when I heard the vacuum sound get lower and lower then suddenly something "gave" and it got very loud and started emitting a burnt rubber smell. It still worked to put liquid into the carpet; seemed to have trouble getting it out. I checked the tank, filters, belt, and roller and all seemed OK - but when I started up again and looked down I saw sparks in the motor/belt area and shut it down immediately. Any thoughts?


The bearing that is located at the top of the vacuum motor has failed . Because of that the shaft of the motor's rotor is out of position and the pulley attached to it has started rubbing on the other pulleys, giving you that smell. the spark appear ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

My Rainbow SE powerhead suddenly started making a different noise that almost sounded like something was stuck. The brush bar was turning ok. I took the plate off and the belt was very hot but I could see nothing wrong. What could this be?


... Rainbow 75th Anniversary Canister Vacuum

Belt problem My belt broke. I put a new belt in, followed the instructions, seemed to be right but as I started using the vaccuum, it starting smelling like burnt rubber. The belt was extremely hot. Took it apart, tried again and the same thing happened. Please help me!!!!


Get the old lady to use a dustpan and brush instead SORTED ... Kirby Generation 3 Bagged Upright Vacuum

Roller not turning, belt not working no water . The belt on my Bissell Proheat is not getting water (although there is plenty in the holding tank). It seems the belt is not turning and there fore the water is prevented from leaving the holding tank.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have a Kirby Dual Sanitronic '50' Vacuum Cleaner I bought in 1966. The motor does not start when I attach the belt lifter of the rug nozzle. When I remove the rug nozzle and detach the belt from the motor fan shaft the motor starts when I depress the nozzle switch and the power switch . Seems like the brushes in the motor are worn out. I do not have a manual for this unit. Can you assist me as to what newer unit is this compatible to and the problem I'm having at present??


... Kirby Vacuums

I heard that a class action lawsuit against Oreck Vacuum is being started because of all the problems customers are having with their vacuums. Does anyone know about this? My Oreck is only a couple of years old and keeps burning up belts. I took it in after only one week of usage when I started to notice white smoke coming out of it and the smell of burning rubber. I feel like I got the old run-around, when the service tech told me he couldn't find anything wrong (but replaced the burned up belt


You are correct about the fact that legal action has been taken. Go to this link to read more\015\012\015\012 ... Oreck XL2200 Bagged Upright Vacuum

I checked the belt and it has not broken, but when I start to vaccum the spinning head stops, and I start to smell a rubber smell...Do you think I need to replace the belt, I did get some string caught in it the last time I vaccummed, and it did stink like rubber then also...


Yes you do need to replace the belt they stretch out. Think of a belt like a big rubber band if you were to stretch it out and hold a lighter to it the rubber band would stay stretched out. That is the same thing that happen ... Bissell Vacuums

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the


... Dirt Devil M088905 Vision Bagless Upright Vacuum

Smoking belt Hey I have a Eureka 2961 avz bagless vacuum, and if it's on for a few minutes i can smell the belt burning.  If the vacuum is left on any longer the belt starts smoking.  I took the case off and there was a little debris but not much.  Is there a cause and fix or just time to replace the belt?


Belt is slipping because the bearings on the beater brushes, which it turns, are jammed or full of dust. \015\012Alternatively the belt has stretched after being overheated and needs replacing because it now slips. ... Eureka 2961AVZ Bagless Upright Vacuum

The belt burnt out and it seems as though the red arrown does not release the belt. Like it is backwards from the green arrow. It had a burning smell and the belt broke. Then the second belt started to burn out when the brush roller wasn't spinning. Not sure what might be wrong. Green light will not come on either.


It sounds as if there may be a piece of the broken belt in there. Look carefully with a flash light and remove any remnants you find, using a pair of pliers if you have to.\015\012\015\012Also, remove the entire brush roller assembly and ... Kirby Ultimate G Bagged Upright Vacuum

The Belt on my Dirt Devil broke...so I purchased another belt and as soon as i put it on and started to vacuum it also broke, i noticed that the metal piece the belt goes on was extremely hot and was melting the belt. Whats wrong with it?


It may be that the beater brush is bound up . This will cause slipping, of the belt. Take out the brush and clean out the bushing . Hair gets wound up in side. once you have it cleand out. Put a few drops of cooking oil in side the bushing on both e ... Dirt Devil& Breeze Vision Canister Vacuum Vacuum

The brush roller stops turning and I can smell the belt burning, then it will catch and start working normal. I looked under the plate to check the belts and they looked okay and no hang ups of string or anything. The only thing that seemed weird was that the smaller belt that actually attaches and turns the roller is a bit loose. The larger belt is tight but looks like its the one that is burning and causing the smell.


Better to replace both belts the smaller one is stretched out thats whyits slipping ,be sure to clean the old rubber off the motor shaft before replacing the belts.it will cause the new belts to run unevevly and go bad before their time ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The belt on my vacuum cleaner model 6596 bissel powerforce bagless turbo keeps breaking. As soon as I put on a new belt and start it up the belt snaps. It is the durabelt meant for this vacuum model. Also, my son has been having the same problem with his. He has the same model and same belt. This problem is occurring even after a thourough cleaning.


I would guess you aren't centering the belt correctly, thus it's edge is caught between the brush and another solid object, causing the breakage.\015\012When you get the belt on the the brush and the brush back in place, turn the brush a few ti ... Bissell 6596 Bagless Upright Vacuum

The belt on my Kirby G3 wore out, and I bought replacement belts from two different sources--one an official Kirby supplier and one a store brand. Neither belt is long enough to catch the belt lifter when it is rotated and to reach the drive shaft.


Kirby has only had 1 belt from day one. sometimes you do need to push the belt up to catch the belt lifter ... Kirby Generation 3 Bagged Upright Vacuum

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn


Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

Eureka Bravo with new belt & bag suddenly won't start. I replaced a very worn and slack belt with a new one, vacuum then ran for maybe 20 seconds then shut off and now won't restart at all. Bag was also changed at same time. Is there a fuse, maybe? New belt too tight? Thanks


... Eureka Bravo II Bagged Upright Vacuum

I changed the belt on my bissell Cleanview revolution 3596 twice and both times the belt burned and starting to smoke. I'm not sure what to do now I have two broken belts what could I be doing wrong?


Sounds like the brush that the belt runs (or is supposed to run) is being kept from turning. If you can get the brush out to clean it and lubricate the ends that go into the holder clips, this should solve the problem.\015\012With the new belts burn ... Bissell CleanView 3596 Bagless Upright Vacuum

What is the secret of installing the belt? When I start in the off position & turn it to the belt on position, the belt is not picked up. It appears that the hook is backwards.


Kirby has produced a good video that shows you step by step how to change your belt. They show the Sentria model but this procedure is the same for every Kirby model. You will notice in the video that they mention the numbers on the side of the brush ... Kirby Generation 3 Bagged Upright Vacuum

On our Hoover U6445-900 (Mach 6.9) we replaced the small belt that goes to beater brushes in front of unit. Upon starting, the Hoover quickly got hot and smoky. We shut it off and looked things over carefully, but the second try also resulted in friction heat on the belt. Now it appears the belt may have stretched due to heat and the brushes won't spin. Any ideas?


Are you sure you purchased the right size belt..the friction you speak of is usually caused by a belt not being the right tightness or a jammed beater brush ... Hoover U6446-900 WindTunnel Bagged Upright Vacuum

When I turned on the sweeper it would not start. I put a different power cord on it and it worked fine. now it won't start but the light on the brush and the bag full will flash when i turn it on and off but it wont start. i have 2 of these doing the same thing. do you have any idea what could be wrong. I have checked for clogs but have found none. Bob


Its sounds to me like the computer board inside the machine has gone bad. Keep in mind that the filters in these machine do need to be replaced regularly to keep the vacuum working correctly. Any good vacuum shop should be able to fix your problem. R ... Windsor SR12 Sensor Bagged Upright Vacuum

Need instructions how to use Hoover Steam Vac Spin Scrub. I borrowed it from my Sister and she left it with no instruction book or letting me know how to operate it. I put water & cleaner in top tank. That's all I know to do. Do I put any water in bottom tank? I figured not, since that is probably where the water goes when sucked up by vac. Do I leave lid on bottom tank? I usually use a commercial cleaner, and this is very different. I need to know NOW, as I must return it to her today, and I'm


I did have a solution in just a few minutes. Someone responded with a solution that gave me the website where I could go and print the manual in pdf, so did that, and checking instructions I was able to clean my carpets and get the shampooer back to ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover Self Propelled Wind Tunnel. Keeps throwing off drive belt. New belt. Starts up fine, as soon as you release and lower handle, belt comes off spindle


Hi, it sounds as though that when you release the handle, I no this puts pressure on the brush or spindle, this is causing the belt to come off. You need to remove the roller brush and check it for any thing that may have rapped around it causing it ... Vacuums

Belt squeels when the roller starts turning. only used about 10 times. Small belt under cover is very loose, but it shouldn't be worn out after only about 10 uses. does the small bell just rest on the belt control pin or is it supposed to be around it (thinking it could have slipped off)


Ours did the same thing in about 10-15 uses, the idler pully quits holding the v-belt tight and the the aggitator wont turn. ... Hoover U5194-900 Mach5 Multi-Chamber Cyclonic Vacuum Cleaner Bagless Vacuum

My Kirby shampooer - G4 - hardly used any water from the tank and no suds at all. Pet hair did blow out of the small slotted holes in the tray as I moved the shampooer back and forth, but the carpet was basically dry. I did vacuum before shampooing, so the brush part seemed to work great during shampooing, but no water! The small screen was stuck in the crook of the hose that attached to the tank so I did get that out and put it on the small hole on the tank, but it didn't make any difference. I


Few things:Make sure the sponge and the valve under the sponge (water tank) is clean.Make sure you follow the instructions (f you do not have the manual you can find one ... Kirby Ultimate G Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1435 seconds