Having problems with your Bissell Powersteamer 1694 Upright Vacuum ?

I need insructions to replace the pump and brush belts on Bissel 1694W Powersteamer


Answers :

See the image below
f6698bb.jpg

1. Turn off power switch and unplug from the outlet.
2. Using a Flat head screw driver, insert the blade end into the lower slot of the belt access door to release the lower snap. Insert the blade end to the upper slot to release the upper snap.
3. Examine the belt for breakage. You should be able to see the pump belt looped around the motor shaft.
4. Replace if its broken or missing.
5. Once completed replacement return back the belt access door and power on the unit.

If you still have some questions just post back.
Please do rate my solutions.
Thank you for using Fixya.
Alp
Hi,
0df28a3.jpg
To Remove Broken Pump & Brush Belts:
1)Turn the Power Switch OFF and unplug from
wall outlet.
2)Step on Handle Release pedal and recline
handle on floor.
3)Remove the Tank-in-Tank. Set aside.
4)Remove the Belt Access Door located near the
Ready Tools Dial. Insert a Flathead screwdriver
into the slot nearest the handle to gently pry off
the door.
5)Turn the machine onto its side so the belt
access area is facing upward
6)On the bottom of the machine, near the belt
access area, is a red retainer plate that holds
the black brush arm and brush in place. Using
a Phillips head screwdriver remove the screw
that holds the red retainer plate in place. Set
red retainer plate and Phillips head screw aside.
7)Remove the black brush arm that holds the
brush in place. Set the black brush arm aside
(see illustrations).
8)Remove the "toothed" Brush Belt from the
brush then from the red pump pulley. Set the
"toothed" Brush Belt and brush aside.
9)Locate and remove the broken pump belt.




To Install The Replacement Pump & Brush Belts:
1)With the unit still on its side, loop one end of
the replacement Pump Belt around the red
pump pulley and the other end around the silver
motor shaft. Do not twist the
replacement Pump Belt.
2)Re-install the "toothed" Brush Belt first onto the
red pump pulley and then onto the "toothed"
end of the brush
3)Re-install the brush into the base of the unit.
4)Place the black brush arm onto the brush and
slide black brush arm into original position.
Re-install the red retainer plate and Phillips
head screw.
5)Using your finger, gently spin the replacement
Pump Belt on the silver motor shaft.If assembled correctly, the
replacement Pump Belt should rotate freely
around the silver motor shaft and drive pulley
without obstruction. The brush should also rotate
freely when the silver motor shaft is turned.
6)Turn the machine right side up. Replace the
Tank-in-Tank and Belt Access Door.
Assembly is now complete.

Here is the user manual about how to replace the pump and brush belts
Click here to download

Page no 15 and 16 will guide you with pictorial representation.

post a comment for further assistance.
Thank you for using fixya have a nice day:-)
Repair Help & Product Troubleshooting for Bissell Powersteamer 1694 Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I need insructions to replace the pump and brush belts on Bissel 1694W Powersteamer


See the image below1. Turn off power switch and unplug from the outlet.2. Using a Flat head screw driver, insert the blade end into th ... Bissell Powersteamer 1694 Upright Vacuum

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a


... Bissell ProHeat Deep Cleaner Upright Vacuum

Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there's two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it's a ribbed belt? that is the water pump belt?


Just taken ours apart with the same problem... found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places - the bottom of th ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I need instructions on replacing the belt that drives the brushes on a Bissell powersteamer pro deluxe carpet cleaner. Could the broken belt have anything to do with the suction of the cleaner?


Here is a link to the belts you need and a link to the manual:Bissell 1697-7 Manual and Replacement Belts ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Need to replace a brush belt - Bissell 1697-7 Powersteamer Pro Deluxe Vacuum


Accessories and replacement parts for your Bissell 1697 Powersteamer Pro are available here:\012\012 ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Bissell Powersteamer 1694W won't extract water from carpet. Was extracting fine until the pump/brush belt gear broke off off the pump. I repaired the gear with super glue and the brush is once again working fine. I now have an extraction problem. What did I do wrong? I took it apart and was so proud of myself when I fixed the original problem. Now I'm lost.


Check your re-assembly.\015\012\015\012Have you missed a pipe connection somewhere? ... Bissell Powersteamer 1694 Upright Vacuum

Schematics I went to replace the belt, and when I put it back on I noticed the silver pulley that the brush belt goes on has came unattached from the red piece by the motor belt. It is one peice. I can order a new pump, but I need the schematics so I can replace the pump. http://www.vacuums24x7.com/bistclpa.html How can I enlarge this so i can read it?


Well you can right click the picture and save it to your desktop, I did it, but it was alittle blurry. But if this doesn't work for you, post me your email addy and I can send you a better picture. But take the top off, there are 6 screws, 3 on ea ... Bissell 8910 ProHeat Clear View Upright Vacuum

Replacing the Brush and Pump belt on Bissel Steam Cleaner 1901


... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Need to replace the brush belt on Bissell Proheat Pet Model 8910


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.


You need a new belt. ... Vacuums

Machine will not pump out water. Brushes work, motor works, new belt, Just will not put out any water??? It is a Bissell Powersteamer,Clearview 4 row brush , dirtlifter.


IF you take the tank out of the base you will see a recepticle where the tank nipple fits into the base. There is a cross looking pattern in the recepticle. Take a pointy object and press down inside the cross area between the bars in the little pie ... Vacuums

Need to replace the main belt on my Bissel 1698-P. Can't figure out how to get the belt around the brush roller. Have the top off. Cleaned the water tubes, didn't let the water come down.


Remove belt access door at left front of unit.\015\012\015\012Unplug the unit. Remove the two solution tanks.Remove spray tips from guides.Remove the brush and cog belt by removing the screw from the orange retaining collar.\015\012Remove belt ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

I have a bissell 1698 powersteamer. i have already cleaned heater and completely cleaned all parts , checked the mix piston, checked belt. it will not shoot water or mix. the motor runs, it will **** water and the brush turns. is it the pump and does the pump just shoot the soap?


Pump is probably bad. When you put the lid back down, did you put the piston on the bottom of the smart mix knob? Also the smart mix knob should be in the water only selection when the top is pushed all of the way down. Also sometimes the flow ind ... Vacuums

I have a broken pump belt on my bissell powersteamer proheat. The belt was just laying in there. I have a new one but no where in the manual does it tell you how to replace it and where! Help


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1698-1 PowerSteamer ProHeat Plus Upright Vacuum

Bissell cleanview helix makes loud noise when the roller is engaged. The motor runs quiet when the belt is disconnected. Do i need a new brush roller? I already replace the belt


... Bissell 21K3 CleanView Helix Bagless Upright Vacuum

I need the belt that makes the brush spin - Bissell 1697-7 Powersteamer Pro Deluxe Vacuum


Here is the belt you need:http://www.vacbelts.com/bissell-6960-w-belt-combo-pack.htm ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

The belt p/n 0100623 broke - need instructions on how to replace it - we have Bissell ProHeat Powersteamer


I just replaced mine last night. 1) take off the top belt cover. 2) take the water and cleaning solution tanks out then lay the unit on the side so the bottom of the cleaner is facing you (water and solution may leak out so you might want to do this ... Bissell Vacuums

I am trying to replace the style 7 belt on the 32074 bissell and need help doing so....its the one that the brush ride on!!!!


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=749442\015\012Generic problem for all Vacuums\015\012I am trying to replace\015\012Posted by pimpjnya o ... Vacuums

Need to replace a broken brush belt on Bissell Pro Heat Model # 88910-W


Easy, unscrew the bottom plate, keep in mind that most bissell shampooers have one belt longer than the other based on the left vs right side\015\012\015\012hope this helps ... Bissell 8910 ProHeat Clear View Upright Vacuum

Trying to replace pump belt on bissell cleaner


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

How do I replace a pump belt for my Bissell 8910


This link is a video of belt change for the bissell proheat. ... Bissell 8910 ProHeat Clear View Upright Vacuum

The gear that turns the dual brushes on my Bissell Spot Lifter 1716 seems to be stripped. The belt looks loose as well, but when I take the belt cover and the brush assembly out, the gear that turns the brushes is loose and appears to be stripped on the cogs. When I turn the machine on the belt turns the gear but the brushes just sit there an vibrate. They make an attempt to turn now and then but not much. Need to get a schematic or the parts so I can order the gear if it is available and th


... Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn


Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

Dyson DC07 I actually need to locate and replace the brush as it split on one end. Looks like I need to pull the belt off to do that. Might as well replace the belt while I'm at it.


Hi.\015\012\015\012Depending on wether your machine has A clutch fitted will decide how easy this job will be.\015\012\015\012The non clutched model is very simple turn the 3 plastic screws on sole plate to unlock position lif ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1182 seconds