Having problems with your Bissell ProHeat Deep Cleaner Upright Vacuum ?

My deep cleaner keeps shutting off, even after I try multiple sockets around the house. It's clean so why?

Answers :

There's a blockage inside it. The only way to find it is to completely dismantle it.
Repair Help & Product Troubleshooting for Bissell ProHeat Deep Cleaner Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My deep cleaner keeps shutting off, even after I try multiple sockets around the house. It's clean so why?

There's a blockage inside it. The only way to find it is to completely dismantle it. ... Bissell ProHeat Deep Cleaner Upright Vacuum

Suction button Although my Hoover Spin scrub is working perfecting dispensing the solution, when I go to suck up the solution from the carpet--I am having problems with the RED suction button that keeps popping up. I have to stop the cleaner and lift up the dirty water container to break the suction. Ive tried cleaning the netting that is encased around it, but still no luck. Any help would be appreciated! Thanks

This happens when the filter on the inside of the lid for the dirty water tank is pushed all of the way up. You need to leave a 1/4 in. gap from the top to the top of the filter ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Got a Electrolux twin clean vacuum cleaner still keeps cutting out every 20 seconds even after cleaning and turning filters around

... Electrolux Vacuums

I have 2 mood lights (90843C - 925600010602) within 2 weeks of each other, when switched on they light up for under a minute and then go off. I have tried them in various sockets around the house to ensure it isn't a problem with the socket. Any ideas ? Thanks, Jan

... Vacuums

My Scooba floor cleaner "check tank" light stays on even after it's refilled and everything cleaned but still will not work. It just keeps beeping at me when I try to start it. How do I reset it or get the light to turn off so I can wash my floors?

Flush out the solution valve with water (aka "prime the pump"). Use water, not just air, because water will clear any obstructions that may be in the lines. Also, rinse your tank through the four ports on the *underside*-- one round, two oval, one la ... iRobot 5800 Scooba Vacuum

Roomba Discovery Roomba is fully charged and cleaned with sensor wiped clean. When turned on it it sounds normal and commences to go, but it then acts like it is putting on the breaks, spins, tries to go and manages a short distance and breaks again, just not making any progress because it keeps breaking after a foot or so and turns and tries again. Sometimes is gets so stuck from moving forward at all, like it is stuck in one spot just trying to go while seemingly surrounded by barriers. Somet

I had the same back-up, turn, move forward a couple inches, backup-up, etc. problem. Try cleaning/cutting the hair, etc. out from around the brushes, as well as around the ends of the brushes. Also, try a Q-tip to clean out the four pair of sensors ... Roomba Robotic Floor Bagless Vacuum

My carpet cleaner (bissell proheat plus) is not steaming, dispensing cleaner. Seems like there's a little thingy that should be spinning or turning..... When I work a small area of carpet, it just leaves behind dry blobs of carpet gunk like pet hair. I had to use a carpet sweeper to clean up. FYI - I filled the cleaning fluid container and after trying to clean the carpet, it did empty out but the carpet isn't wet. Any tips? The manual doesn't help.

You need to replace the pump belt. Here is the belt you need:Bissell ProHeat Belt ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My bissell proheat 2x carpet cleaner is not spraying from the bottom or sucking up when turned on. The hand tool works just fine. I have made sure it was on floor cleaning when I used it to try and clean my carpet. the busshes are working but nothing else is happening this cleaner is about 21/2 years old and has only been used maybe 5 times so it has not had alot of use.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My wife and I own 6 IRobots: 1 Scuba 1 Dirt Dog 4 House cleaning vacume models All of them are not working, so I decided to try and solve the problems with two of them: One is a dirt dog and the other a house cleaning vacume Rumba. Given: Battery is fully charged Reaction: I start both of them. They run for about 2 to 3 seconds They come to an abrupt stop as if there is a rock in the gears. Help

Both of them have identical issues? Can you please provide the actual part number of them? It should be on the bottom or inside the battery area somewhere.ThanksTim ... iRobot 1100 Dirt Dog Bagless Robotic Vacuum

I have a Royal 7910 extractor and even though I vacuum before cleaning the carpet, by black cocker spaniel's hair gets pulled into the plastic pick-up attachment and I cannot find an easy way to clean it out. I have tried taking the screws out to separate the halves, but it seems as though they might be glues together. I have run water from a sink sprayer though the openings with some degree of success, but it still is pretty cruddy. I have tried snaking pipe smokers pipe cleaners up the pick

One person wrote this in a review:\015\012Most home carpet extractors are very difficult to take apart for cleaning and maintenance. The Royal 7910 is the exception. No tools are needed to take the front housing off to clean out all the pet hai ... Royal CE7910 Wet/Dry Vacuum

I have an older model F6056-900 Hoover steamvac Spin Scrub Cleaner. My first problem was that I loaned it out to a friend. Anyway she ran over the hose (used for attachments) with her car. I tried using the cleaner for carpet cleaning this morning but when I tried to put the solution tank into place...its loose...won't snap back in like it used to. When I can get it somewhat in place the solution just complete drains out through the bottom fo the tank. The leak is where the small hole on the bot

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a Bissell ProHeat 2x, and I did something dum. I had some powdered cleaner that said it works with carpet cleaners-well I mixed it in-and the next time I tried to use it, nothing came out. So, I took it part to check what was wrong-and found out that the powdered cleaner solidified in places. I cleared the nozzels, nothing. I think the solenoid, between the heater and nozzels is pluggd, and possibly the heater. I've got a question-could I use CLR to clean the heater, with replacing t

Heck yeah, give it a shot. Try running some water through it too- fill it up, heat it just to where it's hot and unplug it, shake it around and dump it out. Repeat. You might have to get a wire or something to go through and get the powder loosened b ... Bissell Vacuums

Electrolux twin clean vacuum cleaner. After 5 minutes it keeps of thinking the filters need cleaning (and they don't). I re charge the power, and all seems fine and then it goes back to wanting the filters cleaned. The suction is also not working to full capacity.

Because the suction is not working fully it feels that the bags must be full and the air cannot be pulled through the bags. It could be due to 1) bags not being of correct quality. The air has to pass through them to allow all the dust to reach there ... Vacuums

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom

Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

When squeezing trigger and Depressing Clean surge Button on Upper handle of the Hooover Steam Cleaner F5914-900 there is no "snap" indicating trigger rod is in place. Everything else went in as instructed. The screws and bolts were no problem this concerns me because the main complaint I read about this model was leaking from the trigger and clean surge and the problem was not getting the rod in place. No matter how many tries or people (three) it still doesn't occur.

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=552215\015\012Generic problem for all Vacuums\015\012When squeezing trigger and Depressing\015\012P ... Vacuums

DYson DC07 not sucking properly when in upright mode. I have tried cleaning out pipes etc and even tried an old motor section I had in garage (replaced once under warranty as kept cutting out and they left old motor section here). Even the old motor section had same prob so this suggests its something in the rest of the vacuum cleaner (whats left after you have lifted off the green motor section and dust collection area if you see what I mean? Any advice weclome please.

Blocked filters ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a suction problem with my Shark Navigator vacuum cleaner. I tried to clean it and after trying to put it back together, it lost suction. What can I do go get it working again?

... Shark Helmet NV22L Shark Navigator Upright Bagless Vacuum

We have the pet steam cleaner bissell 12 amp, we tried cleaning off the brush, because the cleaner wasnt sucking up the water sufficently. a screw came out along with the belt roller, and we have no idea how to put the screw or the belt back on.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

** suction The best way to describe it is that when I was vacuuming I could see dust clouds at the front of the vacuum where the light is swirling around in the air. It was like it was blowing dust around instead of picking it up. I checked the tubing and found that it was clogged with some paper and hair ***** etc.... So I cleaned it out and tried it again and it still was not picking up properly. I had my husband take all the tubing apart to check for other clogging and there was none. When I

You have an airflow problem. You may still have a blocked intake or tube, also check the filter. The air is supposed to go in the bottom (of course) and I'm sure you k**w where it goes out. You probably can **te a reduction in exhaust. If this is ... Oreck XL Ultra Bagged Upright Vacuum

Cleaning I cannot get the cleaner to release solution on carpet. have lost manual. is there a trick to this? I have tried squeezing trigger handle to dispense solution with no luck. have followed instructions (2 capfuls cleaner, fill with hot water to fill line) on filling tank.

Either you have a pinched or clogged water line, or the rod in the handle is pushing down like it should. The drw back is Bissell has deemed this unit and its parts obsolete. So any parts are hard to find.\015\012\015\012 ... Bissell 1950-3 Quicksteamer Plus Vacuum

HOOVER STEAMVAC Model# F5842-9RM 120v 12 amp Carpet Cleanerworks well. Hooked up upholstrey attachment, used it. Reassembled to standard operation, the aggitator brushes do not work. I dis assembled brush insert verything good. ran cleaner and the square hole that the bushes insert into did not rotate with cleaner on. turned off lightly tried to turn mechinism in machine no luck. Reassembled aganin, reinserted cleaning tool, then disconnected it. agitator still doesn't work. toggled switch

... Hoover Vacuums

I have a new bissell 50c9 upright vacuum and it keeps clogging in the clear window in the back. there is a flap that keeps coming open and filling up. everytime i clean and restart, the flap opens. i tried holding it closed and noticed lose of suction.

... Vacuums

Bissell Pro Heat 7901 will spay through hose but not the floor and red flow indicator will not spin. So we took the housing off and after unclogging a hose running to the hearter, my husband unhooked the hose that goes to the flow indicator, blew in it and it started spinning. Put the deep cleaner back together, tried to use it and nothing. What else can we try? Can't afford to put it in the shop right now. Thanks in advance.

I borrowed my friends bissell to clean my carpet. It's the 7901. He brought it over and told me that it only sprayed out of the attachment hose. He said he couldn't figure out what was wrong. I'm no vacuum technician but, I am a mechnic. I decided to ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I have used my Steam Vac for carpeting, but until today, had never tried cleaning upholstery with the spin-scrub brush. I spent a miserable afternoon trying to control the spray, which seemed to go everywhere AROUND the furniture, but not ON the furniture! Additionally, I never did get the water into the recovery tank, despite many attempts to connect and re-connect the hoses and recovery tank/lid.

I can sympathize. My vac came with two handheld attachments. I have better luck with the handheld attachment that doesn't have the spin-scrub pads. To keep the water from going all over the place, you need to keep the part the you hold only about 1 ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My Kirby 2HD has started making an odd roaring noise but still works fine. I have taken the front assembly off and cleaned and adjusted the roller and checked the belt. The noise seems to come from the motor housing. I have tried to wiggle the main shaft at the front (bearings?) and it seems tight. Can't seem to get the other housings apart. Any ideas? Thanks, John

It is quite possible, it just needs lubed. The motor comes in direct contact with dirt so, you have to make sure the front bearing has a drop of oil on it from time to time. If it starts to scream at you within one month, after oiling, the bearing ... Kirby Heritage II Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1239 seconds