Having problems with your Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum ?

Brushes aren't turning on Bissell Proheat 2X and it is almost new.


Answers :

New or old,flip the vacumm over,and remove the long hair and debris from the roller brushes. If they don't spin after removing any debris,the
\015\012belt,that turns the brushes has come off,or the motor is bad. You wil
\015\012have to take the bottom section apart,to see what's going on,then.
\015\012Good luck.
Repair Help & Product Troubleshooting for Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Brushes aren't turning on Bissell Proheat 2X and it is almost new.


New or old,flip the vacumm over,and remove the long hair and debris from the roller brushes. If they don't spin after removing any debris,the \015\012belt,that turns the brushes has come off,or the motor is bad. You wil\015\012have to tak ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Bissell Proheat I have a Bissell ProHeat 12 amp 6 cleaning brush upright and it won't turn on anymore. We have done the basics like making sure the outlets work, etc. Changed it around to different outlets. It is not turning on. Any idea?


Things to check are the cord, switch, and the motor. ... Vacuums

Brushes run freely on the cog and I put on 2 new belts and new brushes on my Bissell Proheatx2 the brushes do not turn when the machine is running even if I have the handle in the relesed position


I know how frustrating it can be when the brushes don't turn when you're ready to clean.Here's a quick link to troubleshooting steps to assist you:\015\012 ... Bissell Vacuums

Brushes won't turn on the bissell proheat 2X steam cleaner-I don't have the manual to see if there is a button I am not pushing to turn on the brushes. Also, do you put the clean water in the "bladder" in the tank? Sorry I am so dumb-this cleaner was given to me with no manual and I can't figure it out. There is a small tank on the bottom at the back of the machine, that says "formula here" and I don't know if that is where the cleaner goes or what that is for. The machine turns on just fine


... Bissell 8910 ProHeat Clear View Upright Vacuum

Bissell proheat 2x carpet cleaner when the switch is turned on the brushes rotate fot 2 seconds then STOP ,, iIf I turn it off and on again ithe brushes will rotate for 2seconds and STOP again ?? brushes rotate for


Hey, sorry to hear you're having difficulty with the brushes. Here's a quick link to troubleshooting steps.\015\012http://www.bissell.com/FAQDetail.aspx?id ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell Proheat 2x Series 8920 - Brush Belt Metal Shaft Sprocket won't turn


Most likely the brush motor is bad and not turning, part #2036757, would sell for around $23. To get to it, start taking out screws on the top cover, that motor is under the that top access cover. ... Bissell 8910 ProHeat Clear View Upright Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o


Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell ProHeat, Brush won't turn, belt fine.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

When I was using my Bissell ProHeat 7901, I smelled something hot (almost burnt) and turned off the vaccum. When I turned it back on, everything seemed to be working, but the vaccum part was not making the same sound. The bristles are still turning, but it isn't picking up as much and is leaving quite a bit of lint on the carpet. Could the belts be worn? How do I tell? Thanks!


Ya that is probably the issue. Here is a link to the belts you need and to the manual which has instructions:Bissell ProHeat Belts and M ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My brush will not turn on my Bissell 6393 upright bagless vacuum... what is wrong? The belt broke and I replaced it twice... I now have 6 more replacements but the brush still won't rotate. Do I have to get a new brush?


This type of plastic brush roll fails pretty frequently. Hair and other debis gets jammed in the end caps. The hair and debris gets hot which in turn tends to melt the plastic end caps. Remove your brush roll, hold the ends with your fingers and try ... Vacuums

Bissell bagless 6583 brush won't turn after new belt


Sorry to hear about the difficulty with the brush. If your brush does not turn by hand freely, then your brush needs to be replaced. Here is a quick link to order a new brush: \015\012 ... Vacuums

Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there's two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it's a ribbed belt? that is the water pump belt?


Just taken ours apart with the same problem... found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places - the bottom of th ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Bissell 8910e Aromapro. Jams when being pushed along floor. I think brushes drop down and cause problem. However brushes turn when machine is laid flat. Motor works. Doe it need new belt ?


Check your depth adjustment on your brushes ... Bissell Vacuums

I have a Bissell Upright Proheat 2x and the dual power brushes wont rotate. I went to replace the drive belt and noticed the drive shaft does not turn when power is turned on. What shall I check next?


Is there a light that comes on when you "turn the power on." If there is no light, and the unit is plugged in, how do you know there is current going to the motor? Sounds like there might be a break in the cord. Examine the cord near the plug end ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Bissell Proheat 2X brushes are not turning. I have narrowed the problem down to either the brush motor or the circuit breaker How do I determine which unit is at fault?


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Brushes We have A Proheat Select X2. Brand new, using for the first time, heater works, liquid dispenser works, Power brushes on machine and on extension attachment do not turn. Any thoughts? Thanks gigi2244


If the floor brushes don't turn, there is a motor for that and it maybe bad, On the attchment, vacuum is what turns those brushes, On the tank there is a knob to turn for the floor or hose, is it turned for the right application? other then that, y ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Both drive and slave belts are intact and tight on the Bissell ProHeat 2x. The brushes will not turn. When last turned on, there was a loud snap noise and something is broken in the power head drive train. Can we repair this or is there a service center near the Hastings, MI area? We need this fixed ASAP. Thank you.


Sounds likely you should take it in your drive gears might have a problem ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Bissell proheat 2x microban carpet cleaner. no water is dispensing . I have tried double cleaning everything, changing soulation(bissell steam clening) checking the filters checking for hot water, the brushes turn (belt?) What should I do?,


... Bissell Vacuums

I have a Bissell proheat 9200 T. The brushes engage when the handle is lowered. However they only turn for about 20 seconds then stop. If you turn the power off then on they run about 20 seconds again. It is driving me crazy!


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9200 Upright Vacuum

In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.


... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

My bissell brushes are not turning - Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

How to instal a new belt for the brush of the bissell ProHeat


Need to install belts ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Bissell Proheat brushes don't turn. Belts fine.


... Bissell 8920 ProHeat 2XTM Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1154 seconds