Having problems with your Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum ?

The cleaner will not remove the water from the carpet. I have cleaned as much of the cleaner as I can reach. Where is it stopped up or what is wrong


Answers :

Try the following suggestions to see if you can get your machine suctioning properly:
\015\012
\015\0121) Remove the Tank-in-Tank Assembly and place your hand over the motor intake valve. This valve is located next to the Floor Nozzle gasket (at the top of the Floor Nozzle window) and behind the SmartMix Bottle. If you feel vacuum-like suction at this area, your suction power of the unit is working but air is escaping at some point. If there is no suction at the motor intake valve your machine will need to be inspected by an Authorized Service Center Technician.
\015\0122) It is possible the Floor Nozzle on your machine is inserted incorrectly. This would directly affect the suction of your machine. Please follow the directions below for removing and replacing the nozzle.
\015\012Before starting, please be sure the machine is unplugged and the machine handle is reclined.
\015\012To remove the Floor Nozzle window, first detach the Phillips head screws located at the base of the nozzle. Then, remove the Tank-in-Tank Assembly. Next, pull forward at the top of the Floor Nozzle window to release the tabs of this window from the receiving holes of the machine. This window is designed to allow access for cleaning.
\015\012When replacing the Floor Nozzle window, please be sure the tabs at the TOP of the nozzle are properly inserted into the receiving holes provided. If you do not have the tabs in place properly, the suction power of the machine could be affected.
\015\012Rotate the window down into place and replace the screws.
\015\0123) Ensure that the Ready Tools knob (diverter knob) is in the proper setting and the valve opens and closes freely. Ensure the black foam gasket is in place under the valve.
\015\0124) Check to ensure the Tank-in-Tank assembly is seated properly and that it is not full of dirty water. (If this tank has a drain cap, make sure it is in place and that it has a black o-ring).
\015\0125) Check the float and baffle to ensure they are properly installed on the Tank-in-Tank. The larger square portion of this part should be below the clear baffle of the tank with the red flag portion of the float resting on top of the baffle.
\015\0126) Check the Tank-in-Tank and lid for damage. Is the lint screen clogged? Make sure the lint screen is in place on the tank lid and not placed into the motor duct. Also, clear the holes on the lint screen.
\015\0127) Check to see if the upholstery hose has suction. If the hose has suction and the floor nozzle does not, check the diverter valve to see if it opens and closes freely. This can be seen through the Floor Nozzle window as you switch the diverter knob from the floor to tools setting.
\015\012
\015\012If these suggestions do not solve the problem contact BISSELL Consumer Services.
\015\0121-800-237-7691
Mon-Fri: 8am to 10pm ET
Sat: 9am to 8pm ET
Repair Help & Product Troubleshooting for Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The cleaner will not remove the water from the carpet. I have cleaned as much of the cleaner as I can reach. Where is it stopped up or what is wrong


Try the following suggestions to see if you can get your machine suctioning properly:\015\012\015\0121) Remove the Tank-in-Tank Assembly and place your hand over the motor intake valve. This valve is located next to the Floor Nozzle gaske ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Bissell Powerease Lighweight Deep Cleaner. (Shampooer) After I fill the solution tank with the solution and water, I put it in it's slot, but all of the contents just come flowing out. I have only used this machine twice and it worked ok. You are supposed to press the trigger and the solution sprays out and then release the trigger when you want it to stop. But like I said, now I just put the tank on and all the contents come flowing out. I don't know what's wrong or how to stop it.


... Vacuums

Max Extract cleaner stopped sucking up water! Stopped working within an hour of purchasing it! I've taken the dirty water tank apart, cleaned both filters, and it still will not draw the water out of the carpet.


Try returning it to the place of purchase. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Eureka Atlantis carpet cleaner and a little water always leaks out of the bottom. Recently, the head of my handheld upholstery cleaner keeps leaking water. How do I get it to stop? Thanks.


... Eureka Atlantis 2595A Upright Wet/Dry Vacuum

I HAVE A BISSELL PROHEAT CARPET CLEANER 7920 I DISSEMBLY IT TO CLEAN IT. I DON'T KNOW IF I PUT THE HOSES BACK IN THE RIGHT LOCATION BECAUSE AFTER I PUT IT BACK TOGETHER IT'S LEAKING WATER ALL OVER THE FLOOR BUT IT WILL RECOVER THE WATER FROM THE FLOOR AND THE SOLUTION WON'T SPARY OUT I THINK THE HOSES ARE NOT IN THEIR RIGHT LOCATION TO STOP THE FLOW WHEN IT'S NOT SUPPOSE TO BE COMING OUT CONSTANTLY HELP PLEASE IS THEIR A HOSE DIAGRAM FOR THE HOSES INSIDE THE CARPET CLEANER


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Brushes stopped The brushes stopped turning while using the cleaner. I removed the brushes to see if the spindle was broken, it wasn't. I then removed the top plastic cover and checked the switch that engages the brushes; it didn't seem to be moving correctly. There's one spring on the switch - should there be two? Or do you think something has broken on the inside? Thanks for any help


Most likely the turbine is bad, it may just be clogged up, you can take it apart and clean it out real good. That may work, but it may not. Sometimes it is best to replace the turbine. ... Hoover F7431-900 SteamVac Vacuum

I HAVE A BISSELL PROHEAT CARPET CLEANER I DISSEMBLY IT TO CLEAN IT. I DON'T KNOW IF I PUT THE HOSES BACK IN THE RIGHT LOCATION BECAUSE AFTER I PUT IT BACK TOGETHER IT'S LEAKING WATER ALL OVER THE FLOOR BUT IT WILL RECOVER THE WATER FROM THE FLOOR AND THE SOLUTION WON'T SPARY OUT I THINK THE HOSES ARE NOT IN THEIR RIGHT LOCATION TO STOP THE FLOW WHEN IT'S NOT SUPPOSE TO BE COMING OUT CONSTANTLY HELP PLEASE IS THEIR A HOSE DIAGRAM FOR THE HOSES INSIDE THE CARPET CLEANER


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I have a Hoover Platinum carpet cleaner, and it has stopped dispensing cleaning agent and water. This model has a separate tank for water and separate tank for shampoo dispensing. It also has a power hand unit that dispenses shampoo. All along the hand unit has continued to dispense shampoo. Symptom #1, the water tank seemed to be taking on shampoo, as it was getting sudsy. Symptom #2 - On wash mode, nothing would come out, on Rinse mode, sudsy water would come out. Later, symptom #3 - not


Somewhere on the outlet is a control tap thats driven by a rubber band and something is up with this control ,best advice here is put it in the boot of the car and take iot to a hoover dealer ,they will do it seconds for you ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

The water tank on my bissell proheat 2x is not keeping the clean and dirty water separate. I;ve checked the container and there doesn't seem to have anything wrong with it. Also when I switch the machine on you can see the "washing" action, after a few minutes this seems to stop - there is water and forumula in the machine. Only had it a year!


... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Model F5888-900 steam vac how much water and cleaner to I put in -


... Hoover F5888-900 SteamVac Upright Wet/Dry Vacuum

Put too much cleaner in, bubbling alot, turned off, dumped water & refilled. Won't start now.


Yes, let it stand for 48 hours with all parts exposed to dry air. then try again. ... Rainbow E series Canister Wet/Dry Vacuum

I have a Model 116.35922500 Kenmore upright vacuum cleaner. It makes a loud air noise when using the vacuum. I have disconnected and removed the hose to see if anything is lodged in the hose and it appears clear. It makes the noise when the hose is connected. When I remove it, the noise stops. When I place my hand over the hose, the nose re appears. I sounds as though the noise is coming from the fan or internal parts of the machine. So, when there is a load or pull on the machine, it mak


... Kenmore Progressive 35922 Bagged Upright Vacuum

While using, steam stopped coming out in force at the port levels in the head. Suddenly started high pitch whining, pressed button just above connection site and end flew off with great force pouring water onto floor and carpet. Unplugged immediately for safety and unable to get it to deliver steam force again. Less than one year old and used only 8-10 times only in walk areas where there is no carpet with distilled water. Please, advise, cannot find booklet. Thanks So Much, Beverly Crumme


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it may not be getting steam to the head...Euro ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Hello :) My bissell proheat upright steam cleaner is not shooting any water out at the bottom and I was wondering what could be wrong. The handheld part is working fine, its only the vacuum part thats not squirting out any water.


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My hoover carpet cleaner does not extract water. The brushes stopped turning since more than a month and now it doesn't extract any water. The engine is turning on but it does not work properly. I've checked for the solutions to this problem in the manual but any of the causes listed there apply to my machine. Thanks for your help.


... Hoover F5826-900 SteamVac Upright Wet Washer

I bought one of these units last year and it worked great for about 9 months and then it stopped brewing coffee. Not sure what is wrong. It will not heat the water to make the coffee. Any idea as to what could be wrong?? Thank you. Pierre


Hi,Either the heating element is completely corroded with mineral from the water or the heating element has gone bad...If it is not heating at all there is some kind of electrical problem or the element is gone bad... ... Vacuums

My filter queen majestic quit working. I opened up the unit to see what was wrong and I did not immediately notice anything wrong. Upon furter examination I noticed one of the traces on the printed circuit card was burnt. I used a soldering iron to "bridge the trace and it appeared to fix the problem for a while. Now it has stopped working again, and when I jumper the trace to run the motor it seems to work. Should I just replace the card? Or is there a more serious problem with too much current


I recommend replacing the card. Soldering involves the risk of further damaging the card, so it would be useless anyway. Why waste valuable time?\015\012There is a possibility of the motor overheating, generally due to a blockage in the airfl ... Filter Queen Majestic Canister Vacuum

My Pasquini Livia 90 S/E will not stop heating water. This builds up too much pressure. I have unplugged the machine and let it cool off and turned it back on and got the same result. I can relieve the pressure by opening the steam valve, but since the heating element does not turn off it builds up too much pressure very quickly


Your thermostat is failing. Given the initial price tag, look at your warranty options first. If you are out of warranty, then lets proceed.Since there is not a parts / assembly diagram to be found, you will need to disassemble your esp ... Vacuums

Carpet Cleaner i was cleaning my carpet and it stopped putting out water. I changed the water tank and checked the solution everyhting was fine. what chould I do


Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be o ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

FILLING INSTRUCTIONS. I HAVE A BISSELL PROHEAT PLUS 12 AMP CLEANER. HAVE LOST MY MANUAL. NEED INFO ON FILLING THE MACHINE. DO I MIX THE BISSELL CLEANING SOLUTION WITH THE WATER? IS THERE A SEPERATE PLACE TO PUT THE CLEANING SOLUTION, IF SO HOW MUCH SOLUTION PER WATER CONTENT. THANKS


Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My Bissell Proheat Turbo puts out too much water and cleaner and won't **** it back up like it should. Also when I use the attachments dirty water runs out the the hose when I am done. It's used a lot, I shampoo all the carpets about 2 times a month and I shampoo the funiture 1 time a month. I bought it about 3 months ago.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have a Bissell proheat clearview force.The water has stopped running through the cleaner .It looks as though it's fitted correctly, but somehow won't pull the water through.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Steam cleaner stopped sucking up water. Motor still running. It's blowing hot air. I checked the seal on the water recovery tank and it appears ok.


Steam vac won't **** up water ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hi I own a Bissell Proheat Powersteamer pro-tech with a turbobrush. I have been using "bissell multi-allergen removal formula for carpets and upholstery." I ran out of that last night. Today I went to walmart looking for more. Everything I found said "2x Ultra Concentrated Bissell multi-allergen." I'm confused on where to add the cleaner. I have a water tank and a separate soap tank. The instructions on this new cleaner bottle say to add 4 capfuls for the formula tank and dilute with hot tap wat


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

I have a new STEAM VAC Dual V All Terrain Carpet and Hardwood Cleaner. I have used it once and it worked well. Now, the second time, I have no water return. I checked the tank location, the brushes are moving slowly (but the plastic surrounding around the brushes moves as well ??) Water is coming out. There is hot air blowing out, but there is no air suction. What is wrong? Ursula Litzcke


Hello litzcke.\015\012There are lots of people facing this problem as well as other problems with this machine. As there are lots of faulty with this product; would not **** up water/air/shampoo, will not brush and lots more. If it is under war ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0830 seconds