Having problems with your Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum ?

My ready tools dial on keeps coming out, when I put it back it it doesn't seem to be doing anything but just plugging the hole is it suppose to connect to something inside the machine

Answers :

Repair Help & Product Troubleshooting for Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My ready tools dial on keeps coming out, when I put it back it it doesn't seem to be doing anything but just plugging the hole is it suppose to connect to something inside the machine

... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Water leak I just bought this steamer a few days ago, and already I am having problems, when I fill the water tank that your suppost to fill the water runs out before I even turn the machine on. I have tried using plugs to keep it from doing this just so I can shampoo my carpet, this seems to work to a point, considering the fact that there are two holes underneath close to the brushes and one just a little ways back from that location. Do you know if this is something that should have plugs or

If you just pruchased this, then it is under warranty, take it along with proof of purchase to a warranty repair shop and have them fix it. If water just runs out, then there may be a seal missing or a water line off. ... Eureka Atlantis 2595A Upright Wet/Dry Vacuum

The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?

As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Rented triumph 430 and cant figure out how to work the accessories. I have the vac hose and a smaller hose attached ro dispense solution. There appears to be no way to plug in the smaller clear hose. Was I supposed to get another length of hose to connect from fitting on accessory to machine?

Yes don. call the store where u rented and tell them. ... Vacuums

No suction Hello - any help with this would be much appreciated! I just changed the bag and filters. The machine runs, seems normal, but there is no suction. There is no blockage of the hose, as indicated by the fact that that little viewer window above where the hose connects to the unit is not showing the red portion that it shows when there is something blocking the hose (god, this is hard to describe!). If I disconnect the hose and put my hand over the hole, I feel some suction. But

Well, it actually sounds like there is a blockage. Try removing your hose and dropping something through it, like a quqrter. If it comes through, no clog. If it is clogged, I believe that machine has a blower on the upper part of the cleaner (mayb ... Miele S514 Solaris Electro Plus Vacuum

No suction I cleaned and checked all hoses, sounds like something is stuck inside, like a sock, took machine apart as much as I could and couldn't find anything. Any suggestions?

Ok first thing to do is remove & clean the 2 piece premotor filter or purchase new.Now remove soleplate from bottom of machine to do this rotate the 3 plastic screws to unlock position. Lift sole plate off now remove any blockagers or ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

NO POWER My Dyson DCO4 Absolute (purple&lime) won't' switch on. I've checked the plug fuse, wall socket and also filters and hoses on machine all seem fine so think the problem is with the on/off button (maybe loose wire or something) but how do i get to it, is there a special way to remove the green on/off button in order to check the connection? Thankyou in advance for the help i am sure you will be able to provide.

The problem is almost certainly a fatigue break in the flex. These usually happen where the flex enters the handle through the rubber sleeve near the on off switch. You will need to cut about four inches off the wire and reconnect it to the switch. ... Vacuums

I have to rewire the plug on a Pfaff Dorina 75 sewwing machine (foot pedal & electrical input. I cannot get it right - anyone can tell me what to connect to which of the three connections in the plug ?

The colour of the wires differ depending on where you are. If you're in the USA and using 120V system the wiring isBlack (the hot wire) goes to the brass connector, The White goes to the Silver connector and the green goes to the Earth connec ... Vacuums

Please please help me! I recently bought an Empisal Celebrity 550 Sewing machine, I've used it maybe 4 times up to now. Yesterday I was sewing with it and everything was working perfectly, today, when I got home, I plugged in the sewing machine and started sewing, just to see that the bottom stitch is completely loose. It's making this loose loops instead of stitches? I didn't change a knob or anything from working with it yesterday to today, so I don't understand how it all of a sudden doesn

... Vacuums

My kirby sentra won't **** up anything. I've changed heads and bags to see if something was stuck inside but couldn't find anything.

Your inferance proves that the fault could be with the vacuum pump. Since the rest has been checked and there is a drastic reduction of the suction rate of the pump, I think the motor must be checked. Please remove to see if there is accumulation of ... Kirby G6 Bagged Upright Vacuum

Singer knee operated sewing machine power cord with 3 flat pin holes to connect to machine - I need to purchase one of these.

... Vacuums

The brushes spin very, very slowly and stop altogether sometimes - like they just don't have any power behind them.I've cleaned the brushes and also turned it on without the brushes inside to see if the female plug that the brushes go into turns - it does, but not very fast. My husband said he thought he smelled something - like burning. Is there a way to take the underside cover off and clean something?

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have my vacume electrical cord tangled inside and disconnected (I can see the open end of the connection from the power cord collector wheel! I need to take the vacume apart so get access to the wire inside. I need to know if there is something else to open other than the 4 screws. Your help is highly appreciated in advance.

Since you did not provide a model number for your vacuum, it is difficult to provide any precise directions regarding disassembly.\015\012\015\012However, most vacuum cleaners are fairly straightforward machines, and as long as you unplug ... Vacuums

I have a Craftman 5hp snowthrower model 53688501 that will not start. It will fire with gas down sparkplug hole, but runs only untill that gas is burned up. Fuel is present at carb, but I noticed that there are two brass fittings on each side of the carb for vacume lines or something, and they have no lines connected to them. Did I lose the lines that should be connected? Or do I have some other problem. The unit is 4 years old and has the Briggs and Stratton eng model 9A413-0202-E1

This sounds like the carburetor needs disassembled and cleaned. This happens over time and the tiny orifices plug up. Usually from letting gas set in them for extended periods of time and it gums up. If you are not familiar with them, I would take ... Craftsman Vacuums

I have a Series G Kirby Model G7D. The other day when I was vacuuming all of a sudden the TechDrive (Power Drive Assist N/D) pedal fell off. I see the hole that it goes into but when I put it in it's loose and falls out and doesn't control the power drive anymore. When I shook the vacuum I heard something rattling around inside the vacuum head. So I unscrewed the bottom and looked inside and found a small metal part labeled K3 on one side and T on the other side. It looks like it would fit

Hi, I have a Kirby G4 and i'v replaced the carbon brushes myself using a step by step guide however since its been back together it worked for about five minutes it then started sparking from the inside!!(a lot!!) I'v obviously touched something i sh ... Kirby Ultimate G Bagged Upright Vacuum

Am attempting to get 'inside' the vacuum to troubleshoot why it suddenly stopped running. Suspect it may electrical, and have already checked the obvious (visible cord and plug.) However, there doesn't seem to be an obvious way to get inside the canister without destroying something. Thanks!

Hi There,\015\012\015\012Here's a link to a repair solution that I've done explaining how to diagnosis the cord reel, and open up the machine. The model this is done on is not the same exact model as yours, but the repair will be almost ... Miele S251 Flamenco II Bagged Canister Vacuum

The soap dispenser on my 2X is not dispensing. I wrote with this initial problem and received a reply. We did everything recommended to find a clog. To begin with, we poked holes thru the little holes on the underside with a toothpick. Next we took the machine all apart as directed and cleaned out anything that had accumulated (such as pet hair). Eventually we emptied out the soap dispenser, filled it with a hot salt water solution and let it sit for 10 min. I ran three tanks of hot water

Hello,The solution to your problem is already solved, since your soap dispenser is still under warrant,What i will suggest is that you contact the company that supply you this product and explain everything to them, it is most ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Model 116.35922500 Kenmore upright vacuum cleaner. It makes a loud air noise when using the vacuum. I have disconnected and removed the hose to see if anything is lodged in the hose and it appears clear. It makes the noise when the hose is connected. When I remove it, the noise stops. When I place my hand over the hose, the nose re appears. I sounds as though the noise is coming from the fan or internal parts of the machine. So, when there is a load or pull on the machine, it mak

... Kenmore Progressive 35922 Bagged Upright Vacuum

We have the GE sensor microwave WES1358DN1WW. It was made in 5/2009 & bought in July of 2010 brand new. it worked perfect til last week. i put something in it & it started to make a loud humming/vibrating noise. i assumed it was just something ontop of the microwaved & ignored it. 1 min later my food was still ice cold. we tried unplugging & plugging back in & made sure that it was clear of anything but it still makes noise & doesn't heat. GE charges $79 to look at it, & since the microwa

... Vacuums

We replaced the short hose that connects the sucking part to the hole where the dirt goes underneath my Dyson DC07 but now the side of the hose that needs to attach to the machine falls off.

I know the hose you are talking about it is called the DC07 internal hose. Over time the ends can stretch and perish which will mean y ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Sunbeam Model Number 4065-000 and there is white particles comming out of the holes in the bottom. I think it is because we used tap water and there is a lot of deposits in the water. I read on the box that it was ok to use tap water and not distilled water. Is ther any way to clean the inside out to get the deposits cleaned out without affecting the possibility of doing something to the cloths that I will iron after cleaning the iron?

If the deposits are recent and still fairly soft, running a tank of vinegar through the machine should remove the deposits (obviously not using on any clothes, hold it over a sink). if the deposits are more stubborn, you can use a cleaning agent like ... Sunbeam Vacuums

Hi, I have been given a beautiful Husqvarna Prisma 980 and the power seems to have stopped getting to the machine.. The first time I plugged it in it worked, all the lights came up where they are supposed to, then the second time nothing =( Some help would be appreciated as I would like to fix it instead of throwing it in the bin Thanks Vicky

If you're really serious about getting this machine running, you need a service manual. Here is a .pdf download manual:\015\012 ... Vacuums

The Neutral/drive pedal fell off our Kirby G5 vacuum cleaner. I opened up the area housing its connection to the transmission and a couple of the parts were just laying inside. I need a diagram for assembling it and see if I am missing any parts. It was a refurbished machine and a paperclip fell out of the housing when I opened it. Can you help me?

Hi,In the below links you have the parts diagram as you asked will this helps you?If not let me know i will help you more.http://www.fiorijanitorial.com/s-19-kirby-parts-and-bags-generation-3456.aspxhttp://www.vacu ... Kirby G5 Bagged Upright Vacuum

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac

On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Clogged vacuum Rather stupidly, my boyfriend 1) were vacuuming without a bag and 2) vacuumed up a big piece of cotton from a sofa cushion. And now it's making a horrible noise and I see it vibrating where the tube connects to the machine. When you look inside there's a white thing sticking out but it looks like it's part of the vacuum. If it's a clog, how do you fix it? I tried unscrewing the tray the bag sits in but it won't budge.

You can start by taking off the bottom plate or top cover, which ever comes off, that is where the inlet starts going in and hopefully the clog is there. Could be in the hose also. But without the complete model number I can't look it up to see a p ... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0524 seconds