Having problems with your Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum ?

Can't get brushes back on bissell pro heat 2x model 9300

\015 Took apart to clean and can't get back together\015

Answers :

Repair Help & Product Troubleshooting for Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Can't get brushes back on bissell pro heat 2x model 9300


... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have a Bissell Powersteamer Pro Deluxe, Model 8804 shampooer. I got this bright idea to take the brush off as it was full of hair and debree. Upon putting it back on it appears I'm not getting the brush on properly. Does the belt go around the end with the grooves? Also do the grooves go on the right or left side? From my view point I am looking at the machine with it lying on it's back and I am sitting on the floor looking at the bottom of machine. Sure hope I haven't confused you too m


... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

I have a bissell pro heat model 7901-B that has power but no water circulation. I was told that the previous owner used it without water and that she couldn't get it the power on. I bought it off of her and cleaned it out and now the power works, but there is no water circulation. The brushes run and heater works, just can't seem to get it to circulate water. Thankyou for your time, Don


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Cant get cover back on Bissel Pro Heat


... Bissell 8910 ProHeat Clear View Upright Vacuum

Belt I have a bissell pro heat model number7901-1 and i dont know how to put the belt back on. The old one broke and i cant find my book.


First take off the cover on the left side of the top cover, then turn it over, remove the screw holding the red lock and pull the cap and brush roll out, remove the cap, remove the cogged belt, then you can put the new pump belt thru that slot, put o ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

CANT GET MY POWERSTEAMER PRO DELUXE MODEL 8804 BACK TOGETHER


Http://newzealand.bissell.com/images/IncludeContent/Service_Center_Help/Upright_Deep_Cleaner_Repai ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

How to replace parts that hold brush on model 1699v bissell pro heat steamer serial no o417130411


... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I purchased a Pro Heat self propelled Bissell rug cleaner model 7950 from Target wherehouse on 4-26-06. I used it once and all was fine. The next time that I went to use it the smart mix for the cleaning formula would not dispense formula.I called Bissell consumer services and was told to take it to Starks Vaccumn in Sherwood, Or. That was on 10-30-06 They said that it was working so I tried it again and not a drop of formula was or has been used since.I took it back 2-13-07 and the replaced the


I assume that it is spraying water? Is the smart mix knob turning freely from one point to the end? If not then there is a problem with the smart mix asm. With liquid in the soap bottle, push the valve in to see if liquid comes out ok, couild be ... Vacuums

Hello, My mom has given me her Bissell carpet cleaner. (It is NOT a vacuum.) She has lost the manual!!!! Could you get me one? It is a Bissell Power Steamer Pro, Model 1697 Also at the bottom of the cleaner it says "Dirtlifter Power Brush".


Here is a link to the manual at Bissel's site:http://www.bissell.com/images/UserGuides/1697_908.pdf ... Vacuums

Bissel shampooer I have a bissell shampooer powersteamer power brush model 1694-W. I cant get it to dispense water onto the carpet anymore. I think it's because I let my 3 year old ride on it while I was shampooing. I assume I have depressed some special little part that is now broken or mashed or something. Stupid I know....


Yes there is a belt on the side that will need to be changed ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Need to replace a broken brush belt on Bissell Pro Heat Model # 88910-W


Easy, unscrew the bottom plate, keep in mind that most bissell shampooers have one belt longer than the other based on the left vs right side\015\012\015\012hope this helps ... Bissell 8910 ProHeat Clear View Upright Vacuum

How do i put the brush back on a bissel pro heat pet shampooer


... Bissell Vacuums

Bissell 1699 I have taken apart the pro heat cleaner. I reassemble it. The top cover will not go all the way down. Any suggestions on getting back together. Thank you


Make sure that the piston on the bottom of the smart mix valve is in the water only position.(needs be be on the knob and not sitting in the hole). With the top off, it is easier if you have a block of wood or something under the base to hold it up. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I need a manual for a Model 9200 07145C Bissell Pro Heat 2 Carpet cleaner, where can I get one?


Try here:\015\012http://ec1.images-amazon.com/media/i3d/01/A/man-migrate/MANUAL000074560.pdf ... Bissell 9200 Upright Vacuum

I can't get the brushes to rotate and the water to spray on the bissel pro heat 2x.


I have a Proheat 2X and had the same problem. I tried the Water Rinse setting and found water came out and was suctioned properly, but on the Light Clean, Normal Clean, and Heavy Traffic settings, the unit failed to do anything. Problem may be with ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

How do you get the smart mix dial to line back up when replacing the top plastic cover on a bissell pro heat pet.


First, insert the black plastic control valve all the way into the hole. Make sure that the rounded face with the cut in it is facing toward the tall part of the chamber/hole where you inserted the valve. Try to line up the dial with where the thre ... Bissell 8910 ProHeat Clear View Upright Vacuum

I have Model 9400-3 Bissell Pro heat select 2X microban. I cannot get the solution to come out to shampoo the carbet. I cannot find my instructions that came with the shapooer. Please help.


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Where can I get Bare floor attachment & A Turbo Brush for model Pro Heat 9200 2X ?. Not listed on official site please quote prices.


Call me tomorrow i'll get the price for you w/ shipping614.868.0799 josh ... Bissell 9200 Upright Vacuum

I have a Bissel pro heat 2X and one of the wheel assemblies has become dislodged from the housing. How do I get it back in?


Hi There,Ok, so in order to get the wheel assembly back into the machine, you're going to have to take apart the machine, or at least the housing underneath of the clean/dirty solution tank, as well as the housing that the shampoo solutio ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

How do I get the beater brush off of the vacumm to replace the belt? The vacumm is a Shark roadstar . I can get the belt on the one end but I cannot get the brush up to put it on that end. Judy It is a Shark Roadstar EURO-PRO Model No. UV208C


... Vacuums

My bissel pro heat cleane's brushes stoped. I checked the belts. They are okay. There is no sign of heat or problems around the motor. Is there a mercury switch some where in the handle so the brushes only turn when the handle is lowered?


Depending on which model you have, you did not say, if the cogged belt goes to the pump pulley, the cogs may be wore away or and won't turn the brush roll. On some other moels, there is a brush roll motor that may have gone bad. ... Vacuums

Bissel pro heat model 8910


Go to http://bissell.com/images/UserGuides/7901.pdf\015\012\015\012This is in pdf format so you need adobe reader to get it, which is free on the ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

How to I take apart and front and back of the Bissell 8910 pro heat.


... Bissell 8910 ProHeat Clear View Upright Vacuum

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.


... Windsor VS14 Versamatic Bagged Upright Vacuum

Brush not moving in Bissell pro-heat


If the belt is more then 6 months old or more, then the belt will have to be replaced reguardless of the way it lookes. belts can stretch over time and when you put the machine on the carpet the friction causes the brush to stop because the belt has ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1036 seconds