Having problems with your Bissell rug shampoer ?

How to replace electric wire

Cord is going to the bottom

Answers :

Repair Help & Product Troubleshooting for Bissell rug shampoer

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Replacement motor I purchase a replacement motor for a F5897-900 Hoover SteamVa Motor part # 43576197 or 27242051. The replacement motor has three electrical connectors + ground were as the orginal has two electrical connectors + ground. Do I ingnore the the thrid connector and hook up the wires to the same connectors as the orginal or do I have to do some rewiring.


The manual only show one wire from the motor going to the switch, the other going to the cord, then the ground wire. I would wire it the way your old motor was, could be that some models maybe were 2 speed and the other wire would be used for that. ... Vacuums

The power wand electrical connection on the power unit itself seems to be corroded. I think I need a new two wire plug to plug into the wand. the model is a Eureka 6984 A. I am able to disassemble the power unit if necessary and replace the wire and plug if one is available


Try hesco inc they have a on line store with all the vacs parts diagrams and fast shipping. ... Eureka Vacuums

Replacing the Oreck vacuum cleaner motor with a generic Ametek motor, the wiring terminal are different and I need an electric diagram


... Vacuums

Mrs Cleaner flex has pulled out how do I replace Electric supply wire to switch on handle has broken at switch. How do you remove switch to repair? tonysimmons


Hi\015\012\015\012\015\012\015\012\015\012\015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE. I have a kenmore whispertone 8540 canister vaccum. The electrical wires (3) to power the beater are embedded in the hose, in a spiral fashion. The yokes that hold the hose on both ends (and attach to the beater on one end and the unit on the other) have no screws or pressure latches; i don't want to use brute force as i may damage the attachment device inside the yoke. If someone can tell me the trick to get these yokes off each


Should be a pry off dot on the underside revealing a screw ... Vacuums

Reinstalling a hampton bay ceiling fan model-HL52QV P 3LC14 and I do not recall how to wire it to the house electric. A black wire and a blue wire are tied together and a white wire are present fromthe fan. Whichone is connected tothe hot wire in my fan electric box inthe ceiling.


The black and blue wire should conncect to the black wire in the electric box and the white wire should connect to the white wire in the box. This assumes the wiring was correctly installed.Jim ... Vacuums

I have a d4c rainbow vacuum, need help replacing the electrical cord


You have to splice them. \015\012Use crimp-on wire connectors (best), or threaded twist-on wire connectors. Do NOT just twist wire strands together and tape wires without using wire connectors . . . that is a NO-NO. ... Rainbow 75th Anniversary Canister Vacuum

Replacing electrical cord


Burned board means replacment, you will have to buy a new board.You can have a look at some of the baords by visiting here :http://builtinvacuum.c ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Wiring diagram for Model #11635922500 - KENMORE Upright vac I took the cover off of the vacuum to repair the power cord and must have pulled a wire out of its wire nut by the sweeper bar. If I had a diagram it would be no problem to replace. The bad has four short gray wires coming out of it. It is one of the gray wires that has come loose.


... Kenmore Vacuums

Local vacuum repair shop replaced motor in Oreck XL 2600HH and now the lights blow out immediately upon powering up the machine. I believe the wires for the lights were mis-wired to the terminal blades on the motor housing. is there a wiring diagram available to properly connect the wires to the motor housing?


Hello. if this repair just occurred return this vacuum to that repair shop as they owe you a valid repair. I agree that they caused the lights blowing out problem. They must repair this for no charge. If you work on it yourself they will blame yo ... Oreck XL2600 Vacuum

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin


... Vacuums

Replace electric cord to switch recliner rocking chair. that controls raising of foot rest


... Vacuums

Wiring the switch for a kenmore vacuum cleaner I need to know where teh different colored wires go. It had a short in it so I replaced the plug but think I wired it incorrectly. Its a Whispertone 300 model 116.28612790 The canister works but the beater bar doesn't.( it worked before a rewired the switch. Thanks


... Kenmore 23313 Whispertone Bagged Canister Vacuum

Wiring Schematic I need the wiring schematics for my XL3600HH, as I am replacing the motor and did not receive the schematics. Unfortunately, I can not remember the exact wiring. Please help. Thank you


Hope this will help you. There is 4 different ways to hook it up depending on what you have,\015\012\015\012 ... Vacuums

Electrical im trying to re-wire a new supply cabble and all the wires have become disconnected.do you have a wiring diagram?


I have the same vacuum at home and can take a picture, but I believe it is wired in this order. Hot wire (black) from cord goes to the switch then the switch to the fuse, then the fuse to the cable that goes down to the light and motor. The neutral ... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

I have a Janome Model 556, purchased in 1968 in Zimbabwe. I need to know how to replace the wires of the foot pedal. There were 4 wires used to go into the small plug attached to the machine, however the wall plug only had 3 wires.


... Vacuums

Confusion and embarrasement have caused me to appeal for expert advice. I need to add a second flourescent light fitting in the loft. I recently added one from the existing wiring circuit via junction box and pull chord switch and it works fine. I have wired in the second light and now neither of them work. I have replaced the starter (as I had a faulty one in the first light. But i annot get them to work. I have installed a second junction box for the second light and wired all like terminals


... Vacuums

Replaced Oreck power switch. 2 black leads and 1 white lead for switch. Posts marked 1, 2, and 3. 2 black wires to switch powers on. Connect white wire and breaker trips. Where does the white wire go?


Both black go to the switch. Power in - black to switch / white to white from motor. From motor - black to switch / white to white from power cord The black wire from the power hooks to ... Vacuums

Eureka Boss 4D (5892BVZ) - Switch Replacement & Fried Wires


If you got the handle apart, Id say you can probably fix it yourself. You might be able to patch it but I would say to maximize your effortrs please visit RepairClinic.com to find the exact replacement parts you need. They also have expert advice ... Vacuums

I had to replace the switch in my Kirby G6. It took some doing but I got in out and the new one in. I must have miss labeled the wires because when I pull backwards the clutch pushes forward. Ther


Go to kirbvacuums.com and look up your model number ,they might even have a toll free number you can call ... Kirby G6 Bagged Upright Vacuum

I have a Eureka Central Vac CV1601b. The motor does not stop unless the Unit is unplug from the electrical outlet. Any Idea?.I removed the control unit to check if there was disconnected wires or burnt wires. Everything look normal. The circuit board does not show area that overheated. There seem to be 2 relays. Likely one of the two went bad. What do you think.


If the unit is relay controlled, there is always the possibility that when the unit was turned on, the relay contacts welded themselves shut making the power button ineffective. \015\012\015\012If you're familiar with relay pinouts, with ... Vacuums

I have an older Oreck XL vacuum that sounds like it is running twice as fast as it should. I disassembled the entire vacuum, including disconnecting the motor wires, to clean out the hair, string, and other things. When I put everything back and connected all the wires, everything appears to work, including the light. The only problem is, it sounds extremely loud like the motor is running too fast. The model number is: XL3610HH Ser. No. 3610HHXA039740-6 I do not have as electrical diagram to see


... Oreck XL Ultra Bagged Upright Vacuum

The switch on our Hoover Windtunnel vacuum cleaner is not working. I have located the replacement part on your website...part#Ho-28161067, I've removed the wires from the switch. Is there any trick to actually removing and replacing the switch itself? It seems to be in there rather tight.


No, follow the directions to replacing the switch and you should be good. if you got the kit then splice the wires and replace them with the wires profied and the wire nuts, you should be good. ... Vacuums

I also have a Hoover upright and I need to replace the electrical cord. I have dimantled the back, where the tools are stored, and the hose. I still cannot find the screws or whatever, to get to the area behind the cord, so I can replace it. I think I will have to take off the bottom too. Has anyone out there tried to do this? It seems crazy. This machine works great so I hope I can also put it back together. Thanks for the help.


Since I do not know your specific model I can only supply you with general instructions. Be aware that most of the time you only need to gain access to the on/off switch to replace the power cord. Also Make sure that you are replacing the existing co ... Vacuums

Wiring diagram I have a replacement main switch for my vacuum cleaner. Two blue and two brown but no diagram or markings on terminals to show which wire goes to which terminal


How to Repair a VacuumCleanerhttp://home.howstuffworks.com/how-to-repair-small-appl ... VAX Appliances 2000 Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0524 seconds