Having problems with your Bissell SpotBot Hands-Free Compact Deep Cleaner - Silver ?

When we put our spot bot cleaner on automatic the cleaning solution does not come out. The machine goes through all the cycles but the area is completely dry with no solution passing through the brush.

Answers :

Good afternoon,

It sounds like the spray tip may be clogged. This is all referenced in the product/service manual located here:

There are numerous points of reference in the manual, specifically on page 14:

I hope this helps. If you need clarification or additional assistance, let me know. Have a great day, and please rate this solution!

Repair Help & Product Troubleshooting for Bissell SpotBot Hands-Free Compact Deep Cleaner - Silver

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When we put our spot bot cleaner on automatic the cleaning solution does not come out. The machine goes through all the cycles but the area is completely dry with no solution passing through the brush.

Good afternoon,It sounds like the spray tip may be clogged. This is all referenced in the product/service manual located here: ... Bissell SpotBot Hands-Free Compact Deep Cleaner - Silver

I have a Kenmore 116.36932 (upright-bagless vacuum) that the motor protector by-pass valve has opened. I've clean out the area between the agitator brush where the flexible extension hose starts. There was some blockage there. I checked the rest of the system (extenstion hose, back filter area, pipe area to canister and area to side filter. I took the 2 filters out and the by-pass valve is still open. Where else could there be a blockage that I can take apart to clean and put back together

... Vacuums

My electrolux sidekick, model 1562 makes a nasty screeching sound.It happens as soon as it is powered on,the noise then gets intermittent after qa few minutes and then goes away.This cycle is repeated evry time i use it.I have checked it for binding and obstructions and oiled the motor.I think it's the roller brush but oiling it didn't seem to help

... Electrolux Vacuums

The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?

As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Water and cleaning solution not dispensed when pressing the switch. Heat light is on, water and solution containers are full, brushes and vacuum working. Selector is on floor clean and not brush clean.

Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have a 8955 riccar vacuum. my roller brush is not working very well on the carpet . I took it apart and now I am not sure on how it goes back together. Could you send me a picture of how the rooler part of the roller brush goes back together. Thank You. Paul

... Riccar 8850 Vacuum

My roomba goes round in circles. sometimes it stops and moves a centimeter backwards and then again it goes round in circles. if you press the ,,dock'' button it goes back to the station. if you press the ,,clean'' button, again, it goes round in circles.... the machine is cleaned, the sensors aren't covered with dirt, the weels and brushes can rotate freely.... can anybody help me??? thanks in advance franz

Here's the link. IR Bump Sensor Fix ... iRobot Roomba 560 Robotic Vacuum

When vacuuming carpet with the electric power brush it will ocassionly , go to zero suction mode and shut off the brush. I have tried to cause it to happen by playing with the joint areas ( handle to tube and tube to power brush) without sucess. When the problem does occur I just turn the suction back on and power up the brush again at the handle controls.

You gave a good start to giving us good information to help you with solving this problem-- But I need a little more information:It sounds like you have the Electric Motor driven Power nozzle/ Floo ... Miele Blue Moon Bagged Canister Vacuum

Model # 5770 the brush motor runs and shuts down after a few seconds...Turn unit off and the brush again will run for a second or two...If I don't turn unit off brush will not start up..Could it be the printed board..the motor brushes..or the wiring that goes from the printed board to the main motor...Thank you

Seems like your unit goes into failsafe because it detects something wrong. Well you should check the brushes and replace them if they are worn out. Also check the wiring for shorts etc, becaue the unit maybe tripping due to an overload. The printed ... Bissell Vacuums

I was vacuuming, and ran over an area rug with those tassle things on the end. the brush immediately stopped spinning. so i turned the vacuum off and un-tangled the brush. after replacing the brush and putting the assembly back together, the brush no longer rotates.

Did you smell something burning? You probably melted/broke the drive belt. ... Dyson Ball DC24 Bagless Upright Vacuum

Roller Bar is abrading (removing the fabric of) our carpet. Is there a softer brush or another solution? Has anyone else observed this problem?

Hi Mark,If you're concerned about the suitability of your DC25 for this particular carpet, I'd encourage you to email us at [email protected], as we'd appreciate the opportunity to provide further assistance.We'll look forward to h ... Dyson DC25 Animal Bagless Upright Vacuum

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu

This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

My hoover spin scrub machine has stopped scrubbing. It still dispenses and pulls up the water, but the brushes don't move. I've checked the on off button for brush control and cycled it to off and back on, but no movement out of the brushes.

There is a filter on the front right hand side of my F5871-900 Hoover. If you remove the plastic covering and clean that filter (wet finger may do), you're Hoover will begin spinning again! ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Irobot Scooba model 33501 the check brush light immediately goes on and irobot does not work. I replaced the brush and it still will not run and the brush light remains on.

... iRobot 5900 Scooba Robotic Wet/Dry Vacuum

Roller Brush How do I install the roller brush. I didn't pay attention when I removed it and now when I attempt to vacuum my low carpet it doesn't seem to be working. The green light on the head of the vacuum goes out when I click it down to the floor. It didn't used to do that. Plus I think I smell something burning. Could the belt be broken?

Try a new belt. The ends of the brushroller are different sizes, so you can't put it in backwards. There are numbers and notches on the ends of the brushroll. These notches/numbers need to match on both sides when installing it. (probably need b ... Kirby Ultimate G Bagged Upright Vacuum

Dyson hi my dyson sounds as if something is catching when the brush goes round, it's very loud, it still has good suction. I have taken the plate of can't see anything or fell if there is anything obstructing the brush, could it be the belt?

Hi.\015\012If the brush turns freely then you will need A new clutch unit fitted to your machine.\015\012There are loads of them on Ebay very reasonabley priced only buy new not second hand.\015\012\015\012Manuals are availabl ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

A few years ago we bought a Dirt Devil Carpet CPR and several bottles of the cleaning solution that goes into the sprayer. We are looking now to find additional bottles of that solution. Where can we find it?

For cleaning solution call 1-800-321-1134 cost is $9 ea. + shipp ... Dirt Devil Carpet CPR Vacuum

Carpet cleaning brush noise. When put in carpet cleaning mode, a loud noise comes from the brush bar area. We see no visible obstructions and have cleared threads and hair.

It's likely that one of the brush roll bearings has worn out. This is not uncommon. I think you'll find that you have to replace both the brush roll and the sole plate at the same time. Dyson sell them together as a kit. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

On our Hoover U6445-900 (Mach 6.9) we replaced the small belt that goes to beater brushes in front of unit. Upon starting, the Hoover quickly got hot and smoky. We shut it off and looked things over carefully, but the second try also resulted in friction heat on the belt. Now it appears the belt may have stretched due to heat and the brushes won't spin. Any ideas?

Are you sure you purchased the right size belt..the friction you speak of is usually caused by a belt not being the right tightness or a jammed beater brush ... Hoover U6446-900 WindTunnel Bagged Upright Vacuum

My Dyson CDC14 Animal just started making a wierd sound coming from the rotating brush area. I already cleaned around the brush, sounds like a fast rattling sound.

Hello,Something could be jammed, or not rotating freely, maybe an improper alignment with the brushes, or a blocakage within them. Try to re adjust the brushes :) ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I get plenty of suction at the hose, and none at the brushes. Also, the vacuum will not remain upright when I push it up. It appears that the part that switches the suction from the hose to the brush area is not engaged.

I looked up the problem where the machine would not stand upright, used that solution, and it worked. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

No suction at floor brush. Plenty of suction in the tube that goes to the joint just before the 90 degree turn to go from the handle to the brush area.I lowered the handle so that the tube was straight and probed. The tub is clear. I cann't find the manual at home or on line. The Hoover.com site is useless in searching for a manual.

Are you sure the brush roll is turning. If not sometimes it will appear to not be sucking. Take off the bottom plate, then you can get to the brush roll and belt.\015\012 ... Hoover 5416-900 WindTunnel Bagged Upright Vacuum

Ny Panasonic MC-E4013 has lots of ****, but the brushes don't pick up from the carpet. The drive belts are not broken and the brush roller goes round OK.

Usually, shen you have this problem, there is an obstruction of dirt etc. somewhere in the suction path.You need to take the vacuum apart and clean thoroughly first.Then get back to me. ... Vacuums

I need to clean the brush on my dyson upright vacuum. How do I open the area to remove the brush?

3 silver screws on the underside 1/2 turn anti clockwise and remove cover. cut fibres with small scissors und remove pull gently ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

No suction - dirty solution tank is bone dry; carpet is wet from clean solution. Help! Thanks, Elizabeth P.S this is my second machine, I love them

  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0929 seconds