Having problems with your Bissell SpotBot Robotic Wet/Dry Vacuum ?

Unit starts and immediately shuts off

\015 I fill up the spotbot with the appropriate mix of water and solution and turn it on. It starts and then after a few seconds just stops and the lights all flash. How can this be fixed?\015

Answers :

It has a bad circut board it is a defect and bissell will replace it
Repair Help & Product Troubleshooting for Bissell SpotBot Robotic Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Unit starts and immediately shuts off


It has a bad circut board it is a defect and bissell will replace it ... Bissell SpotBot Robotic Wet/Dry Vacuum

I have an easy flo vacuum model # 199C and it won't shut off. It started out as an intermitent problem but now will not shut off when the hose is unplugged, nor when the off/on switch on the main unit is shut off. the only way to get the motor to stop running is to unplug the unit. Any ideas?


Just had this same problem. I unplugged the low voltage signal wires and the vacuum stayed on. Thus eliminating the possibility of the signal wires shorting out somewhere. I'm not really sure which wire(s) were causing the problem. But when I disasse ... Easy Flo EF1500 Vacuum

My lux 7000 has a new bag but when i start to use it with the power unit or without the unit shut's it self off i can reset the lites or the motor if you will by clicking the on off switch 4or 5 times and i'm ready to go again untill you start to work and off it goes you can repeat the switch thing as long as u want, it just won't let u vacuum ,it turn's it self off .I blew it all out but found nothing in it. if u don't try to vacuum it will run as long as u want to listen to it. Can you


Have you replace the afterfilter? It may also cause this if rather dirty. It's located under the tool caddy/air diffuser on the back half of the machine.\015\012Try this: Disconnect hose, turn on vacuum. Does it continue running? If so, pl ... Electrolux Lux 7000 Bagged Canister Vacuum

I just used my Bissell Proheat, when I heard the vacuum sound get lower and lower then suddenly something "gave" and it got very loud and started emitting a burnt rubber smell. It still worked to put liquid into the carpet; seemed to have trouble getting it out. I checked the tank, filters, belt, and roller and all seemed OK - but when I started up again and looked down I saw sparks in the motor/belt area and shut it down immediately. Any thoughts?


The bearing that is located at the top of the vacuum motor has failed . Because of that the shaft of the motor's rotor is out of position and the pulley attached to it has started rubbing on the other pulleys, giving you that smell. the spark appear ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Model # 5770 the brush motor runs and shuts down after a few seconds...Turn unit off and the brush again will run for a second or two...If I don't turn unit off brush will not start up..Could it be the printed board..the motor brushes..or the wiring that goes from the printed board to the main motor...Thank you


Seems like your unit goes into failsafe because it detects something wrong. Well you should check the brushes and replace them if they are worn out. Also check the wiring for shorts etc, becaue the unit maybe tripping due to an overload. The printed ... Bissell Vacuums

RE: Goldstar dehumidifier: Model #DH404EY6, S/N 602TAQP05412 My unit is ~4 yr. old, has worked w/o problems until now. It will no longer auto. turn on. When I manually turn it on, the motor turns on, and then immediately shuts off, and "01" appears on the LED screen for humidity level setpoint. Is this an error code, and what does it mean? Can the unit be repaired? Thanks, Wolfgang


... Vacuums

I just purchased a black and decker corded hand vac/blower/inflator. I plugged it in (for the first time ever) it started and then shut off immediately. I tried different outlets thinking it blew a circuit in the first one. However it still won't start. Very frustrating!


Unfortunately those units are prone to breakage they are also usually a sealed unit (not able to take apart). The best thing to do would be take it back where you bought it and try to get your money back. They just aren't worth fixing. V ... Black & Decker Vacuums

I have a vx550cc that keeps kicking in and out quickly, then shuts down for a few seconds and starts up kicking in and out again. There is lots of suction at all the outlets and sweeps. The dirt bucket has been emptied and the filter cleaned. Al the LED lights light up when the motor kicks out, then back to one green when it starts back up. This unit has worked great for four years with no problems.


... Broan-NuTone VX475 Bagged Central System Vacuum

Shark/cordless /sweeper - over four years old. Started - but seemed like it was caught and shut off almost immediately. Not used year around - tried to start after absence. I have removed some hair and perhaps dental floss. Checked belt - it seems O.K. Do I need a new battery or is it just worn out.


Check the brush,is there any dirt got stuck in between brush rolls.If there is then it needs to be cleaned.Your cordless sweeper will automatically shut off if an obstruction is caught in the brush roll. the other thing to checks is dust contai ... Vacuums

When I turn on the unit and push on the level that draws the "arm" back, it immediately shuts off. I return it to the upright position and turn it on again and repeat the process. Same thing happens. Took it to an Oreck repair shop (mistake #1) and they couldn't figure out what was wrong. Any ideas?


Seems like there is a short in the unit. it is extremely hard to find kenmore parts. i would probably just go out and buy a new vacuum. Kenmores arent worth fixing. ... Kenmore Progressive Upright Vacuum with InteliClean System Slate Blue

The Roomba 535 runs but stays in 1 spot moves 2 inches turns and repeats the process about 10 times. then a red indicator light starts blinking and the unit shuts down


Any beeps? If so, how many?\015\012\015\012Is there a pattern to the light blinking?\015\012\015\012Not really enough info yet to be certain, but it sound like the cliff sensors may be dirty. \015\012\015\012Here ... iRobot 530 Roomba Vacuuming Robot, White Vacuum

Model C153C The vacuum cleaner starts but stops immediately. If I disconnect the hose it will run but if I partially put my hand over the suction it shuts off. Both filters have been changed.


Hi If the vacuum cleaner works but then shuts off unexpectedly, it may be because of restricted airflow which can cause the vacuum cleaner to overheat and shutdown. Check the vacuum cleaner for clogs and if the bag/tan ... Electrolux Vacuums

On our Hoover U6445-900 (Mach 6.9) we replaced the small belt that goes to beater brushes in front of unit. Upon starting, the Hoover quickly got hot and smoky. We shut it off and looked things over carefully, but the second try also resulted in friction heat on the belt. Now it appears the belt may have stretched due to heat and the brushes won't spin. Any ideas?


Are you sure you purchased the right size belt..the friction you speak of is usually caused by a belt not being the right tightness or a jammed beater brush ... Hoover U6446-900 WindTunnel Bagged Upright Vacuum

My Dirt Devil Vibe bagless vacuum started giving off a burning smell. The brush roller was jammed with hair. I immediately shut it off and cut the hair out of the rollers with scissors until it turned freely. When I turned it back on, the smell was gone but there's no suction now. Did I ruin the belt or something else?


It's more likely there's a clog in the hose somewhere, possibly where it connects to the power nozzle. Detach hose and check the PN. \015\012If there's no clog in the PN, detach hose completely from machine and try to drop a marble or coin th ... Windsor SR12 Sensor Bagged Upright Vacuum

No power, were the power cord goes back into the unit. It started to shut off prior to quitting altogether.


Your cord conductor is broken in the area where it enters the machine ... Fantom Vacums Lighting Canister Vacuum

No power Our dyson DC07 was working fine, then we pushed the button to turn it on. It started to run then shut off and now it is like the power is no longer there. I have checked outlets and they all work. Is there a fuse of some kind in this unit?? If so, how would I get to it?


The motor will have a thermal cut out,however chech your plug fuse and the cable as it enters into the off on switch. its known to snap here within insulation..... ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Epio 6500 canister electrolux won't stay running...says the bag is full even when it isn't. Will start but as soon a load is placed on the unit it shuts down. Any thoughts?


There might be something stuck ... Electrolux Epic 6500 Vacuum

Floor attachment starts (green light) and then, almost immediately stops (red light). I have cleared all built-up dust in the unit, but no change occurred as a result.


Step on the blue lever at the base of the floor attachment to separate it from the long wand. Sometimes there is a clog inside at the base that needs to be cleared. Good luck. ... Fantom Vacums Lighting Canister Vacuum

Stops Immediately. We have a Beam Serenity model 2100 installed in the home and when the hose is inserted into the wall it turns on for a few seconds and then shuts off on it's own. Turning the handle's power switch off/on restarts the unit only to have it once again stop after a few more seconds. The canaster is clean. What could be causing this stopping issue? Thanks.


The Relay Control Board in the 2100 is bad. Replace and it should work just fine. ... Beam Industries 2900 Serenity Plus Central System Vacuum

Electrolux Centralux I have a Electrolux Centralux. When I plug the hose in at one of the wall outlets the motor will not start. If I go to the motor and slap the unit it will start.....then...it will not stop unless I unplug the power cord to the motor. If I plug the power cord back in, the unit will not restart until I slap the motor unit again. The unit has only been used 20 - 30 times. Any suggestions?? Thanks, Bruce


I dont know if you had your unit looked at yet but it sounds like the Power module is going. I repair the machines so I know some of the work. ... Electrolux Centralux Vacuum

I have a Kirby Dual Sanitronic '50' Vacuum Cleaner I bought in 1966. The motor does not start when I attach the belt lifter of the rug nozzle. When I remove the rug nozzle and detach the belt from the motor fan shaft the motor starts when I depress the nozzle switch and the power switch . Seems like the brushes in the motor are worn out. I do not have a manual for this unit. Can you assist me as to what newer unit is this compatible to and the problem I'm having at present??


... Kirby Vacuums

GE Spacemaker Microwave PVM1870 fan keeps running after door closed and won't shut off. Have to open door or unplug. As soon as door is closed and plug is back in, fan starts up. If door handle is pressed downward, microwave starts! If door handle is raised, fan shuts off but light stays on.


... Vacuums

Shuts off when suction starts


Hi there. In Panasonic vacuums, there is a thermostat protection on the motor. It will auto ... Vacuums

Centralux - unit will operate for 10-15 minutes then shut down. We hit the reset button, unit operates for 20 minutes then shut down again. Had customer svc stop by, they checked the hose, filter, no clogs, etc. ANy ideas


Check the screen. It's located underneath the motor. You can see if it's clogged by removing the filter and with a flashlight look up at the bottom of the motor. If it is clogged, the easiest way to clean it is unplug the vacuum, disconnect the two m ... Electrolux Centralux Vacuum

The roomba or I robot will upon pressing the start button go around in circles, than starts to goin one direction, than stops and goes in a circle. The unit is clean and the unit reset. Bill


Is the front bumper **** in? ... Roomba Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0612 seconds