Having problems with your Bissell SpotLifter 2X Portable Deep Carpet Cleaner 1719 ?

Burned resistor i opened the vac and found that the ac adaptor ciruit board had overheated and burned the resistor i need to know what type to replace with

Answers :

I had two of them like this. Order resistor at Digikey. Match the resistor color rings to the online decoder at Digikey so you get the right one. Refresh the Ni-cd battery while you're in there. Search "youtube" for battery fix. It's easy to do.
Hey Pete! You should contact one of BISSELL's Authorized Service Centers to ensure you don't void your warranty.

Here's a quick link to locating one.\015\012


Repair Help & Product Troubleshooting for Bissell SpotLifter 2X Portable Deep Carpet Cleaner 1719

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Burned resistor i opened the vac and found that the ac adaptor ciruit board had overheated and burned the resistor i need to know what type to replace with

I had two of them like this. Order resistor at Digikey. Match the resistor color rings to the online decoder at Digikey so you get the right one. Refresh the Ni-cd battery while you're in there. Search "youtube" for battery fix. It's easy to do. ... Bissell SpotLifter 2X Portable Deep Carpet Cleaner 1719

I have a kenmore grab n go bagless and I need to know the exact size of the belt, I lost the manual, and I have burn several belts at the bigining of the problem the motor stops and burn the belts I open it and I think it was a little piece of plastic, that cause the problem, but when I put the new belt it looks like the motor works fine,but still burn the belt, I'm using UB-1 #5275 belt am I using the wrong one?

... Kenmore 34722 Grab-N-Go Upright Vacuum

The electronics in my Sunbeam TA200A Toaster is playing up. The Toaster is sometime popping the toast up after the right amount of time, but sometimes it pops up a minute later than it should (burning the toast) I have open up the control panel buttons and inspected the array of transistors and resistors that is used for the timing mechanism and a visual inspection doesn't indicate a problem. I am keen to replace the 2 transistors on the control unit (the resistors are unlikely to fail) but I ne

... Vacuums

Somehow I have endd up with a cannister type vacuum cleaner and all I know about it is that it says model:VC-H3301. All I need to know is how to open the container full of dust and dirt o I can empty it. Can someone help?

Here is some info on that vacuum that may help you. it tells who sold it and what brand and where to get filters.\015\012\015\012http://www.fixed4fr ... Vacuums

I have to replace the light bulb and can't find the instructions in the manual. I guess they figure it's obvious, but not to me! I've had it for about 30 years and can't remember the bulb burning out before. I have the replacement, just need to know how to do it.

Hi,What make and model vacuum do you have?Thanks,Handie Andie ... Vacuums

Need to know how to open the canister of my Electrolux Ambassador vacuum to replace the switch

If you switch still"clicks" you need a switch rocker, if it no longer clicks you will need a new switch button. You will get best results with the genuine button from an AERUS Electrolux repair shopThere are a set of body keys under the b ... Vacuums

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating

... Vacuums

The light on my huskystar c-10 sewing machine burned out and i don't know how to replace it, what do i need to do?

... Vacuums

I have a Black and Decker Convection oven catalog # CT0100BC Type 1 (3073283 I need to know how to bake a pie. Mine keep burning. Please advise as I don't have a manual

... Vacuums

How do I know if my Shark Sweeper V1700Z needs battery replacement or if the motor is burned out?

... Shark 10" Cordless All-Surface Power Sweeper, V1700Z

I need to replace the cord rewinder of my Nilfisk King series 500 vacuum cleaner, but I do not know how to open the device or where are the screws. Can you help me?

Http://www.youtube.com/watch?v=13krERCaP0U ... Vacuums

Need to replace Belt overheated and melted onto shaft

Here is a link to the belts you need and to a manual tou can view:Bissell 1697 Belt and Manual ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

I have my vacume electrical cord tangled inside and disconnected (I can see the open end of the connection from the power cord collector wheel! I need to take the vacume apart so get access to the wire inside. I need to know if there is something else to open other than the 4 screws. Your help is highly appreciated in advance.

Since you did not provide a model number for your vacuum, it is difficult to provide any precise directions regarding disassembly.\015\012\015\012However, most vacuum cleaners are fairly straightforward machines, and as long as you unplug ... Vacuums

Need Bissel 1719 series, 1718 series wiring schematic. Charging circuit has burnt resistor. Need to know resistor details

... Vacuums

How do I replace the Powercord on a Fantom XT64K Vacuum. The powercord shorted where is comes out of teh housing. I need to open up the unit & replace but need a service manual of instructions. Thanks Father Lenny

I have done this several times, it's some what simple just take the unit apart and use the old diogram to replace the new one. Or take a digital photo of it opened so you have your own scematic. You should be able to purchess the cord at your local h ... Vacuums

Need Bissel 1715 wiring schematic. Charging circuit has burnt resistor. Need to know resistor details.

Can not believe NO ONE could answer this. \015\012\015\012The R1 resistor basically drops the 9V to around 5V for charging the battery pack. The resistor is a 10 ohm , 2 watt resistor. The other resistor is 220 ohm. This only limits the c ... Bissell 1715-G Spotlifter Bagless Handheld Vacuum

Low suction Replacing filters....need help replacing the belt - anyone know how? But before doing these things, have had a problem with suction....I'll let you know if the problem clears up.

Hi, You can take care of both things at once. Here's how:\015\012Unplug and flip your vacuum over, beater bar side up. Remove the cover base plate that surrounds your beater bar. It's held on with either clips or screws, and usually "hinges ... Eureka 2961AVZ Bagless Upright Vacuum

I think I need to replace the main battery in my small floor vac - the one that can be hand held like a dust buster or work like a small floor vac. I need to know how to remove the battery and replace it with what kind of new battery..

I see my sense of humor is not appreciated...it was only a joke. Anyway, here is what you do: First, slide the battery cover off the bottom of the hand held unit. Remove the battery from the motor housing by pressing the tab on connector “A&rdq ... Vacuums

Need to replace power cord and can't find how to open canister to replace

I had the same problem and could not find the other screws. You need to pry off the power cord retraction button, you will find two more screws under there. It's pretty easy after that!!!! ... Kenmore 22612 Bagged Canister Vacuum

I need plumbing diagram for a bissell 9400 need to replace pumpand I need to know what tube goes where on the machine

You can use the lik below and you find the diagrams you need. Their is also the user manual at the same page. Please note that is on lower part of the web page.\015\012Finally at the same page you find and order all the spare parts that you mig ... Vacuums

Charger schematics found charger not woerking on further investigation determined resistor r-5 burned up. not being able to read the bands on resistor need to now actual resistor value to fix correctly. PS 2 1M ohms connected in parralel works but would like to do it correctly.

WASHINGTON, D.C. - Consumers should stop using this product unless otherwise instructed. \012\011It is illegal to resell or attempt to resell a recalled consumer product. \012\011Recall Summary \012\011 Name of Product: Ryobi P113 Dual Ch ... Ryobi P113 18 Volt One Charger 140501001

Hi, my circuit board resistors are burnt due to my re-wiring the resistor switch. How do I fix this - S3755 wiring diagram?? need to know the correct resistors or get a new board

The only way is to get a replacement board. even the dealers are not provided with that level of wiring diagrams. ... Hoover S3755 WindTunnel Bagless Canister Vacuum

Replace belt i need to replace the belt on an upright dirt devil 086310 vaccume but do not have a manual and can not find how to open the assy to replace the belt

On the bottom, there should be a few screws to remove to remove the plate covering the brush roll. However some may have screws on the top housing to remove the top. ... Vacuums

I heard that a class action lawsuit against Oreck Vacuum is being started because of all the problems customers are having with their vacuums. Does anyone know about this? My Oreck is only a couple of years old and keeps burning up belts. I took it in after only one week of usage when I started to notice white smoke coming out of it and the smell of burning rubber. I feel like I got the old run-around, when the service tech told me he couldn't find anything wrong (but replaced the burned up belt

You are correct about the fact that legal action has been taken. Go to this link to read more\015\012\015\012 ... Oreck XL2200 Bagged Upright Vacuum

Dyson DC07 brush roller is worn and won't make contact with the carpet anymore. I need to replace the brush roller but don't know how...HELP?

Buy the brush over the web etc..\015\012\015\012To take the brush out \015\0121 - Take the outer covering - uese a penny to turn the yellow srews\015\012\015\0122 - Slide the black brush out from the assembly - Try the n ... Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1297 seconds