Having problems with your Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum ?

For a Bissell Pet Hair Eraser the drive belt recommended is a size 8... is this right? It seems VERY small and difficult to replace.


Answers :

No it does not use the style 8 belt. It uses the style 7/9/10/12/14/16 belt. You can view the manual and buy the belt here:

http://www.vacbelts.com/bissell-pet-hair-eraser-belt.htm
Repair Help & Product Troubleshooting for Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

For a Bissell Pet Hair Eraser the drive belt recommended is a size 8... is this right? It seems VERY small and difficult to replace.


No it does not use the style 8 belt. It uses the style 7/9/10/12/14/16 belt. You can view the manual and buy the belt here:http://www.vacbe ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

My Kirby shampooer - G4 - hardly used any water from the tank and no suds at all. Pet hair did blow out of the small slotted holes in the tray as I moved the shampooer back and forth, but the carpet was basically dry. I did vacuum before shampooing, so the brush part seemed to work great during shampooing, but no water! The small screen was stuck in the crook of the hose that attached to the tank so I did get that out and put it on the small hole on the tank, but it didn't make any difference. I


Few things:Make sure the sponge and the valve under the sponge (water tank) is clean.Make sure you follow the instructions (f you do not have the manual you can find one ... Kirby Ultimate G Bagged Upright Vacuum

I have a Dyson 17, the Absolute Brand special for pet hair. I think I have a blockage in the hose. Symptoms are: spewing out fuzz balls and small particles. I have checked all the blockage sites recommended by Dyson and all are clear except a small flexible transparent hose, 6 or 7 inches long, curled up underneath the cleaner head/brush bar unit. Any ideas? I've tried to pull out the stuff stuck in there, but I'm afraid to perforate the hose and I don't know any way to disconnect it.


Try dropping something like marbles into the hose and shake it up and down, may loosen it up enough to draw through.hope this helps you out. ... Vacuums

I have a Hoover pet cyclonic upright model uh70085. the brush won't spin, I thought maybe the small belt was stretched, I ordered the correct replacement belt and replaced it, I still have slack and the brush won't turn. the floor and brush adjustment seems to be working correctly. Thanks, Tom


... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum

My carpet cleaner (bissell proheat plus) is not steaming, dispensing cleaner. Seems like there's a little thingy that should be spinning or turning..... When I work a small area of carpet, it just leaves behind dry blobs of carpet gunk like pet hair. I had to use a carpet sweeper to clean up. FYI - I filled the cleaning fluid container and after trying to clean the carpet, it did empty out but the carpet isn't wet. Any tips? The manual doesn't help.


You need to replace the pump belt. Here is the belt you need:Bissell ProHeat Belt ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Dirt devil vacuum cleaner--trouble vacuuming dirt and pet hair on carpeting --is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up --unless I have just put a new bag on the vacuum... Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums


Try replacing the belt. Rubber belts stretch out after about a year. ... Dirt Devil CE6100 Featherlite Upright Vacuum

My pet hair eraser smells like it is burning all the time and sounds funny. The brush will not spin once you have it on the carpet unless you hold it up a little while you are cleaning but then the whole vaccume is not on the floor. I have cleaned all filters and all and it does the same thing. My sister has the same machine because I raved at how wonderful this thing was for pet hair and mine has not worked right since it was about a year old and hers has had the same exact problem since it was


We had the same problem, and it turned out that the roller wheel height setting had broken, for no apparent reason, and was "floppy" so we had to lock it in to one setting with epoxy. Limits utility, but it works. Sort of. ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

Shark vacuum nh15 replacement pet hair power brush replacement


... Euro-Pro Vacuums

I have 2 wahl hair clippers (homecut) I require size 6 comb and size 9 comb the model No is 441-3411 and 441/0359 has the base plate blade broken, Where can I source past and replacement base plate blade


... Vacuums

We have a new hoover bagless that is a couple months old. The pet hair attachment stopped working. I disassembled it found lots of hair wound around the various rollers and removed - painstakingly thorough i might add. Problem is the brush still wont spin and now the belt seems loose - I think I put it all back together correctly but wondering if there is a trick to this?


Without the model number, I can't look it up, but this has a 1 years warranty on it, maybe take it to a warranty shop. Just take proof of purchase, model and serial numbers. ... Vacuums

The brushes will not rotate on my hoover vacuum. the belts are in good shape, the motor is turning the vacuum motor, but the belt on the brushes seems loose. I ordered a replacement belt but still nothing. Their is a small "idler" but their dosent seem to be enough tension on the belt. Any ideas?


Did you order the correct size of belt? These are the belts you should have:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have the Dyson animal upright vacuum. It's 2 years old and now it just isn't working as well as it once did. Suction seems to be lacking - it's not picking up pet hair or much else from the carpet. I have to go over the spot for a few minutes and still, the hair isn't picked up.


You might want to check and see if your cyclones are plugged with hair. this can happen and there is a great site to disassemble and clean the cyclone here: http://www.exonotes.com/content/node/4 ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dc17 -too much pet hair around the belt gears


I was having the same trouble and it was driving me nuts.  I tried cleaning and it did not work.  Then I tore the brush assembly off and looked up into where the little tooth gear is.  I saw something that did not look right.  The ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have to replace the power cord on my Bissell upright pet hair eraser vacuum because it is damaged from getting run over by the vacuum. Familiar story? Rather than pay a technician a lot of money, I feel I should be able to tackle this myself (went to college and everything). What are some pointers to help me bravely tackle this without the help of a male (no offense guys)?


Of course, its simple.\015\012Use electric tape to make sure the wires never touch, usually a phillips screwdriver will do to uncscrew the machine.\015\012just make sure you line up the cords the right way, positive to +ve and negative to ... Vacuums

My vacuum has not been running right..the beater bar is not picking up and the rollers aren't spinning...the belt doesn't need replaced so what else could it be...everything else seems to be running fine???


The motor shaft that spins the belt may have hair wrapped arount it, causin the belt to slip. You can't miss the burnt odor.\015\012Remove the belt and clean the motor shaft. ... Vacuums

Roller I recently removed my roller to cut all the hair off it and when I replaced it everything snapped right in but when I turned the power on the power worked but the roller wouldn't turn


Hi.\015\012\015\012Did you put the drive belt back on the roller ? ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

The soap dispenser on my 2X is not dispensing. I wrote with this initial problem and received a reply. We did everything recommended to find a clog. To begin with, we poked holes thru the little holes on the underside with a toothpick. Next we took the machine all apart as directed and cleaned out anything that had accumulated (such as pet hair). Eventually we emptied out the soap dispenser, filled it with a hot salt water solution and let it sit for 10 min. I ran three tanks of hot water


Hello,The solution to your problem is already solved, since your soap dispenser is still under warrant,What i will suggest is that you contact the company that supply you this product and explain everything to them, it is most ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bisell Healthy home vacuum stopped working. The troubleshooting guide said there could be a problem in the connection at the handle. None of the phillips screwdrivers we have seem to work in removing the screw that holds the handle to the vacuum. What size phillips screw driver should we be using? If the screw is stripped, how can we get it out to replace it since it is not easily accessible in the handle?


You should use a p2 size phillips. there is only one screw right in the center that holds the handle assy on. frequently that screw backs out and allows the handle to slide back and loose connection. make sure the handle is tightly pressed in and the ... Vacuums

I have a hoover wind tunnel model# u6476-900 and I'm having trouble replacing the belt. The extra belt that came with it was belt # 38528-035 and it's smaller then the old one and I'm having a hard time putting it on. Is this the right size belt?


Yes it is the right belt. the easiest way to get that belt on is to put it on the motor shaft first, stretch and start at the top of the self propelled pulley and rotate til the belt tracks on. you will need to keep pressure on the belt while you rot ... Hoover U6476-900 WindTunnel Vacuum

Clean machine All the belts are fine but the machine does not pick up the water. I think it is clogged with pet hair but don't know where to clean it out. I have taken off the roller, etc. but nothing seems to work.


This is what was wrong with mine....very simple solution to fix:\015\012\015\012Check the bottom of the water reservoir. It should have a black rubber washer attached to the lip that goes down into the main system. If that part is inside the main s ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

No suction I just replaced the bag, and normally after this I have a lot of suction. Now that I have changed the bag I have less suction that I had before. Not even enough to picj up dog hair. I snaked he hose and checked all of the connections. It seems to have an air leak but no amount of tape will fix this. I cleaned the filer as well with warm water and dried it and re installed but still absolutely no suction. I am ready to throw it out! Any suggestions would be appreciated


1, Does the blower (discharge) side blow bunches of air??Yes: Something is clogged from the bag to the hose end. Try blowing out the hose from the discharge side.Or: The bag is not properly seated. Make sure that the plastic piece is ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the


... Dirt Devil M088905 Vision Bagless Upright Vacuum

The roller in the power head will not rotate-- replaced belt & that is not the problem--now what do i check? the right end will move, but the left end seems fixed-- is that correct?


Sounds like the bearings froze up. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?


First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

Lawnmower I have a black and decker hovermaster lawn mower. While mowing my lawn I went over a small stone. It doesn't seem to have damaged the blade but the engine instantly cut out and I am unable to start it again, I have replaced the fuse which has made no difference, Can you suggest anything please.


There may be a thermal fuse fitted to the motor, sometimes they reset when they cool down. Sometimes they are a one shot fuse, when they blow the have to be replaced.There may also be a reset switch on or inside the operating lever/switch. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0842 seconds