Having problems with your Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum ?

How can I change a damaged cord on my pet eraser vacuum?


Answers :

First call bissell then order cord.Then the cord is normally is held by back housing or the front hosing on the bottom of vac.
Repair Help & Product Troubleshooting for Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How can I change a damaged cord on my pet eraser vacuum?


First call bissell then order cord.Then the cord is normally is held by back housing or the front hosing on the bottom of vac. ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

I have to replace the power cord on my Bissell upright pet hair eraser vacuum because it is damaged from getting run over by the vacuum. Familiar story? Rather than pay a technician a lot of money, I feel I should be able to tackle this myself (went to college and everything). What are some pointers to help me bravely tackle this without the help of a male (no offense guys)?


Of course, its simple.\015\012Use electric tape to make sure the wires never touch, usually a phillips screwdriver will do to uncscrew the machine.\015\012just make sure you line up the cords the right way, positive to +ve and negative to ... Vacuums

Change belt - Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum


... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

How to change the belt - Bissell Pet Hair Eraser Bagless Vacuum


... Bissell Pet Hair Eraser Bagless Vacuum

I purchased a brand new Eureka Pet vacuum, sorry don't know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage


If the motor is running, there should be suction. Possible problems depend on whether it's a canister or upright and are:\015\012A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out ... Eureka Vacuums

Pet turboeraser tool not working - Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum


... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

Bissell Pet Hair Eraser Vacuum marking carpet


The brush is always turning on the machine even when your using the tools. try not to set it down on thick carpet , or if you can set it on the linoleum. ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

Bissell Pet Hair Erase does not vacuum.


It is because the belt is worn or stretched and needs to be replaced. Here are the belts you need and the manual which has instructions:Bis ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

Cord replacement I need to replace a damaged cord (the reel works). How do I get the top off so I can remove the back end? Once I get it off, will I be able to change the cord, or do I need to buy the whole reel assembly? (and thanks for the help - I love this site!)


You will probably have to replace the whole reel cord. Depending on your model, on each side, there is a bar in the middle that will slide off, then the 2 halfs will come apart. They will only slide in one direction. If an older model, there are s ... Electrolux Lux 5500 Canister Vacuum

We have had a Dyson DC14 for 5 years. Recently, when I run the vacuum, it whines a high pitch sound. It still maintains a suction and does not seem to have lost any power. I am unaware of anything that was done to change the condition of the vacuum. Concerned what the noise is and if it is damaging the vacuum.


... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have an aerus electrolux guardian canister vacuum. The cord was damaged but the retraction winder is still fine. I have ordered a replacement cord but I have no idea how to remove the old cord and install the new one. Am I over my head?


The winder is activated by a coil spring located in a drum. The drum transmits the power from the wire with 2 circular contacts. To replace the cable you must dismantle the case to access the drum, take the spring pressure out carefully as to not let ... Vacuums

Troubleshoot bissell pet hair eraser vacuum


... Bissell 3920 Bagless Upright Vacuum

No suction and is not clogged - Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum


The motor is bad, when these type of electrical motors go bad the power of the vaccum dies but the motor can still sound like it is running. One way to tell the motor is shot, is the motor while running will be a might louder than it was originally. ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

I was using kirby g5 and I think I stepped on cord and lost power on vacuum. Now it won't start. Could this be a damaged cord..or what?


Either that, or it was pulled so hard, it came disconnected from the vac switch. stepping on a cord rarely affects power. so, check vac switch and outlet to make sure the outlet has power.\015\012\015\012(if you know an electrician or if ... Kirby G5 Bagged Upright Vacuum

Where is the beater bar? - Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum


... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

How do I change the belt on Eureka Pet Pal - Eureka 3276AZ Pet Lover Bagless Upright Vacuum


Unlike most vacuums, this one the screws are on the top of your base. There are two screws one on each side. When looking at the front of the vacuum right side screw is located above the s in 12amps and on the left side screw is located above the p i ... Eureka 3276AZ Pet Lover Bagless Upright Vacuum

Making a loud jet engine sound - Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum


We had this problem also, the easy fix for us was taking out the soil container, then reach in and grab the gray cylinder and twist left to unlock it. pull it out, sometimes pet hair clogs the ports that make the cyclone action. Once you clean it o ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

How do I change the electric cord on my Kirby vacuum?


Hello, younghI was trying to help you out here. Maybe this will help some? I was going backto some customers that asked questions in the recent past and even fartherback. It appeared that no one answeredsome of them, So, I thought I would ... Kirby G4 Bagged Upright Vacuum

Change the power cord on a Eureka series 3270-3275 vacuum cleaner


... Eureka Vacuums

My new Kenmoore Powermate 116 canister has poor suction. I have no pets and light dust. Its not picking up small particles on the wood floor with the floor attachment. When I put my hand to the suction it feels weak. Cleared hose and changed bag. Using again, same issues. This should not be happening with a new vacuum. Is it a bad design in the elbow joint of the hose? I want to return this!!!!


First of all disassemble the handle and hose as much as possible and examine the inside. Make sure there is not any significant debris lodged in the hose somewhere like a plastic bag or something.\015\012\015\012Also check at the top of t ... Kenmore 23912 Progressive PowerMate Bagged Canister Vacuum

I have a Bissell pet hair eraser model #3920. It's been working great until last night. I went to use it and the brush won't spin. It also smells like it's burning. I checked the belt and it looks fine, and the brush spins by hand easily. It's not clogged anywhere that I can see. Anyone have any other ideas? This vacuum is only 8 months old.


- Remove the access panel, which is on the bottom of the machine. There are 4 tabs to lift on the access panel to remove. Start with tab 1 then 2-4 tabs.- Check the brush, and belt for any damage. Clean off any debris on the brush. ... Bissell 3920 Bagless Upright Vacuum

How do I change the power cord on my Filter Queen vacuum cleaner?


First, remove the top filter cap. quarter turn. Remove the three screws from under said cap. The rubber switch cover will come off of the on/off switch pedal there. pull off and set aside. undo the two clamps and remove the motor (c ... Filter Queen Majestic Canister Vacuum

How do i change the belt on my eureka pet pal vacuum


... Eureka 3276AZ Pet Lover Bagless Upright Vacuum

Change fab belt on vax power pet 1 - VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum


... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

Need to change electrical cord on g5 kirby - Kirby G5 Bagged Upright Vacuum


This should be fairly easy to do. With the cord unplugged, take the screw out that it holding the hard plastic cord cover onto the base of the machine. This is where the cord looks like it's going into the bottom of the machine. The next part is a bi ... Kirby G5 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0827 seconds