Having problems with your Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum ?

My hose no longer works no suction buth the vacuume still works how do i fix I checked the hose checked the filters nothing works to get my hose so it has suction.

Answers :

Check the following after unplugging the power cord from the outlet.\012
\012- Check for suction at the back of the unit, after removing the hose where it attaches to the back of the vacuum. If there is NO suction, the machine will need to be taken to a local Service Center for inspection.
\012If there IS suction at the back of the machine with the hose removed, please check the following:
\012Unplug the unit from the outlet.
\012- Check the Pre and Post-Motor filters for debris. Dirty filters can restrict airflow. The pre-motor foam filter is square and located in a pull out tray underneath the dirt cup. The foam filter may be hand washed in cold water with mild detergent. Reinstall the filter when it is completely dry. The post-motor HEPA Media filter is rectangular and located on the side of the machine. Note: The white HEPA Media Post-Motor Filter is not washable.
- Ensure the dirt cup is empty.
- Check the upper tank for build up or clogs.
- Twist the inner cyclone to the left and pull down
- Wipe the inside of the upper tank and separator plate with a
damp cloth moistened with water or mild cleaning detergent.
- Once the inner cyclone is dry, lock back into the machine by
pushing up and turning to the right.
- Put the dirt cup back in
- Check for good suction at the end of the upholstery hose. If there is good suction, make sure the hose is firmly connected to the lower hose on the back of the vacuum. If there is no suction at the end of the hose, check the hose for splits, cracks or clogs.
- Make sure the brush is rotating. If it is not, remove the access plate and examine the brush, and belt for damage. The access panel can be removed by lifting the 4 tabs located at the bottom of your machine. Lift tab 1 then 2-4 tabs to remove the access panel.
- Detach the upper hose from the machine. Insert a broomstick into the hose to push any obstruction through to the opposite end.
- Remove the screw from the left side of the lower hose on the back of the unit, and straighten this section of hose by pulling it down or lay the unit out flat, and roll the unit on its side with the lower house towards the top side. Look through the hose for any obstructions. Push a broom stick through the lower hose to unclog.
Repair Help & Product Troubleshooting for Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My hose no longer works no suction buth the vacuume still works how do i fix I checked the hose checked the filters nothing works to get my hose so it has suction.

Check the following after unplugging the power cord from the outlet.\012\012- Check for suction at the back of the unit, after removing the hose where it attaches to the back of the vacuum. If there is NO suction, the machine will need to be ta ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

No suction I have the central vac type. It has no suction at the can. I pulled the hose going to the walls and tested there...and nothing. I removed the dirt can and checked the motor ...it is spinning but does not feel like any suction. I checked the exhaust and it is pushing strong air out. I also cleaned the filter and still nothing. Is there a relay or something that would cause only exhaust air. I emptied the can of dirt and put it back together and have absolutely no air.....hear the motor

On some units there is a screen that protects the impeller of the motor. If this gets sealed off with debris then it is like putting a potato in the tail pipe of a car. Taking the top off the unit reveals the motor. DO UN-PLUG the unit first from th ... Electrolux Central Vacuum

Poor suction The actual sweeper seems to work ok, but the hose attachment has some suction but not enough to pick up things I think it should and not enough to make the power brush spin. I've checked everywhere I can for clogs, but I can't see anything. And there doesn't seem to be any way to check to hose itself for clogs. I've cleaned out the container and the filters, but there's still a problem.

Check the inlet down by the brush roll, make sure it is open, if it is then the hose itself must have a clog. If the hose comes off, drop something like a marble in one end and see it it comes out the other end, if it doesn't then you have a clog. ... Dirt Devil M1100009 Reaction Soft Touch Cyclonic Upright Vacuum Cleaner Vacuum

I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos

It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum

Hello, I have a Eureka 71b handheld vacuum. There is literally no suction. I checked the hose and it is NOT clogged. I thought it might be the filter so I bought a new filter. Still no filter. The rot

... Eureka Vacuums

It starting to put out a hot type smell. I have tried cleaning the filters real well and even tried to see if there was problem with the ozone filter. We have checked and could not find a jam. I know the hose has excellent suction. The vacumn works but the intelliclean sensors will not. It only takes about 15 seconds or so for the odor to start. Then it gets real strong and it makes my eyes water

Hi,The hot smell could be from the belt or the motor. Turn it on for a moment, turn it off, then flip it on its side and smell the belt that drives the brush. If that is where the smell is coming from, then your belt is burning up. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

I have a Eureka Altima vaccuum and it no longer suctions like it use to and also has a burning smell. I have cleaned all filters, brush, hoses, and filters. There are no blockages. I have also checked the belt and it's still good. Any other ideas as to what may be the problem?

This bagless model gets buildup of really fine dirt in the motor and starts to clog up the fan airducts. You will need to take the motor out and clean it. ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

When I try to use the attatcments, the hose suckks in on itself. There's so much suction the walls of the hose close together and nothing gets sucked in. the regular vacuum still works great.

Hi there,Sorry to hear you're having difficulties with your DC07. From what you've described, it sounds as if you may have a blockage in the hose or wand. The easiest way to locate and remove blockages is to follow the steps shown in our ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

The dirt devil vision wide glide Model 086700W appears to have no suction. I have cleaned the hoses and filter and still there is nothing being picked up. Also, I have checked the belt.

There must be a blockage after the hose, check where the hose plugs into the vacuum. make sure unit is un plugged for safety ... Vacuums

The vacuum does not have suction. I have cleaned the filters, checked the hose paths and the hose won't **** anything up. I even checked with all the filters removed, still no suction. It is blowing air out the exhaust.

Have you checked the belt? ... Bissell 89Q9 Bagless Cyclonic Vacuum

My Bissell PowerTrak no longer has any suction. I have cleaned out the hose and the filters, but it still won't work.

... Bissell Cleanview Powertrak 35933 Bagless Upright Vacuum

The brush does not work on my dc15 animal, there is great suction but after about 20 seconds it sounds like something has got blocked in it although nothing is clogged, filters and hoses have all been cleaned but the brush still wont go round

Hi there,Sorry to hear you're having a problem with your DC15. You might find it helpful to visit the Support section of our website and follow these simple steps: ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

No Suction I get great suction in the hose, but when I plug the hose back into the unit, there is no suction and the air flow indicator line goes completely red. I've changed the bag and filters. I took the small panel off the back and made sure there is no clog, and took the hose off to make sure there was no clog there. Still no suction. Please help.

I about to say that's always a clog of some sort that causes that ... Miele S7210 Bagged Upright Vacuum

My Miele S3141 canister began acting strange this morning. No suction...so I took off the hose and checked for blockage, (nothing). Now I can't get the hose back on the canister. It just slips ar

See this causes and fix it. God bless youAir filter:If the vacuum cleaner won't pick up dirt and has no suction the air \012filter might be clogged. Remove the filter and either clean or replace \012it as needed. \012 ... Vacuums

The vacuum i've had for 6 months has very liittle suction power. checked that the belt is on. cleaned filter. checked to see if hoses were clogged. I used a super vac to suction any debris out of vacuum. still little suction power

As this unit has 3 filters on it, a lot of people forget about the one filter that will cause all of your trouble here. \012\012There is the exhaust hepa filter, no problem, your unit is pretty new, it shouldn't be a problem. \012Th ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

I have a bissell proheat carpet cleaner model 8910-w 08019c.the machine will not add cleaner or water to the floor.I have cleaned all the filters with it still will not work. I have checked all the fluid levels and reseated the tanks and still can't get it to work. What else can I do?

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Recently purchase SC-N500 vacuum cleaner. Worked well only the first 2 times I used it to clean up plaster dust from floor after sanding. Since then it has not worked at all well wiht very poor suction. Fluff gets stuck in the hose and has to be manually removed. Suction power is very poor. I have washed the filter to remove the dust with no difference. Who do I contact in Brisbane to service or assess the problem further.

... Sanyo Vacuums

I have a Dyson DC07 and it has lost suction. I have checked the belt, cleaned the circular filter and emptied the dirt chamber. The hose still has plenty of suction but I can't use the hose the vacuum the entire house.

Here are some things you can check.First you need to see if the problem is with the suction or agitation.If the suction on the hose for using the attachments is low you either need new filters a new cyclone(they are not cleanable) or it is clogg ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v

Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

My dyson dc17 animal will pick up via the hose attachment but there is no suction when you use the regular vaccuum on the floor - you can hear the difference in the suction once you put the floor part down - we took it apart - cleaned it - checked all hoses - still does not work????

Hi its Darran at Dyson.Check that the brush control dial is in the centre position when upright and then moves forward when the head is released. If the brush bar is still not spinning when switched on in the vacuuming position, check th ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My DC17 is only a few months old, but I've already had to clean the filter. Since I reassembled everything, I'm finding chunks of carpet fiber and dog fur on top of the filter inside the filter container. Iam getting slightly less suction from the floor assembly as well. I've checked the hoses, brush, and brushed out the inside of the plastic container, but hasn't helped. Ideas??

Everyone needs to own an air compressor,\015\012if you own a bagless vacuum\015\012\015\012You blow it out every other time you use it.\015\012\015\012Without compressed air, all vacuums will just\015\012basically ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Low suction I have a Hoover central vacuum system. I've reset the fuse box, checked the fuses, all of the lines are clear and there are no holes for escaped air to travel out. The filter has been cleaned as well. The vac works well with high suction when hooked directly to the unit, however when using any of the indoor connections there is extremely low suction. The machine still turns on so I do not believe it is an electronic issue. I have troubleshooted the issue as best I could and would

... Hoover L2310 GUV Central System Vacuum

Suction I have no suction through the hose. I have taken this machine apart, and checked for clogs, have found nothing, but did give it a good cleaning, still I have no suction.

Hello tnwalkergal the hose may have a clog inside the hose at the bend you can take the hose loose and run a broomstick or a yardstick thorgh the hose this is how I find the clog ... Dirt Devil M086700 Vision Bagless Upright Vacuum

No suction vacuum won't pick up -- I've checked the bag, hose...and it seems to have no sucking power. The internal hose may be jammed (I vacuumed up a lot of shredded paper), but nothing as far as I can stick in fingers in. I don't have a metal coat hanger to slip down, but I'm afraid that might tear the hose and then the darn thing won't work anyway. :o(

If it is plugged, try using a tape measure, i know it sounds stupid but it will work to unplug your line and will not tear your hose.. ... Kirby G4 Bagged Upright Vacuum

Poor suction absolutely loved the machine when I first got it. I have dogs so it is getting a work out. however, the suction isn't as great as when I first got it. I have cleaned the washable filter and empty the cylinder after every vacuum. When I use the hose, the suction just isn't there. anything else I can do?

OK- I had the same problem and I took it to sears for service, It still wasn't great. So I proceeded to pull out all of the filters, including the internal filter that is not easy to get get to. I washed it and air dried it, put it all back together ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1008 seconds