Having problems with your Bissell Vacuums ?

HOW DO I REPLACE A POWER CORD? HAVE THE CORD, DON'T KNOW HOW TO TAKE THE CASING APART ON POWERFORCE UPRIGHT


Answers :

Push a SMALL screwdriver under the rubber handgrip. Put a fre drops of alcohol into the opening where the screwdriver is. This will llubricate the grip so you can get it off. After you repplace the wire, use alcohol to put the grip back on. It will evaporate and will not cause any electrical problems.
Repair Help & Product Troubleshooting for Bissell Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

HOW DO I REPLACE A POWER CORD? HAVE THE CORD, DON'T KNOW HOW TO TAKE THE CASING APART ON POWERFORCE UPRIGHT


Push a SMALL screwdriver under the rubber handgrip. Put a fre drops of alcohol into the opening where the screwdriver is. This will llubricate the grip so you can get it off. After you repplace the wire, use alcohol to put the grip back on. It wi ... Bissell Vacuums

I have my vacume electrical cord tangled inside and disconnected (I can see the open end of the connection from the power cord collector wheel! I need to take the vacume apart so get access to the wire inside. I need to know if there is something else to open other than the 4 screws. Your help is highly appreciated in advance.


Since you did not provide a model number for your vacuum, it is difficult to provide any precise directions regarding disassembly.\015\012\015\012However, most vacuum cleaners are fairly straightforward machines, and as long as you unplug ... Vacuums

How to take apart to replace power cord - Miele S183 Powerhouse Bagged Upright Vacuum


Hello,In order to access the cord on the Miele S183 upright, you'll need to first remove the handle from the vacuum cleaner. There is a large screw that holds the handle in place that is located under neath of the lower cord wrap hook. ... Miele S183 Powerhouse Bagged Upright Vacuum

My Bissell powerforce 6579-2 is making a loud noise and i want to repair it myself but i dont know how to take it apart?!


The loud noise is probably coming from the beater bar section of the vacum if you flip it over there is a cover thats held on by some philips head screws if you pull the cover off you will see the belt connected to the beater bar and the motor someth ... Bissell 6594 PowerForce Bagless Upright Vacuum

I want to take apart a kone dirt devil and i know how it has to be done but i dont have 5 hands to do it. there has to be a tool that presses on the four sides of the case so you can slide the motor unit out. can you help me with this


... Dirt Devil KONE Cordless Hand Vacuum Vacuum

I have a Dirt Devil Upright Vacuum Model 088525B. I need to replace the power cord. How do I take the vacuum apart?


... Dirt Devil Vacuums

No power. I was getting intermittent power with my miele s558 midsize canister, but it was predicated with me fiddling with the retractable cord to get it to come on and then not move the canister while I was vacuuming. Now I can get no power. I have taken it apart and can see no issues with connectors, cord, casings, etc. It all looks fine. It is about 5 years old and I have had no problems with it.


... Miele S558 Red Velvet Bagged Canister Vacuum

Power cord Cord is just all knotted a twisted, i bought a rubber cord and just want to replace the original. I have removed all the screws from the rear of the machine and it still doesn't want to come apart and i dont want to force it. any help is appreciated.


If the cord goes in at the top, take the handle off, then remove the tool holder, then you can get to the cord. If it goes in at the bottom, You have to take off the motor cover to get to the connecting end. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?


Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

Our meile vacuum has a short in the power cord - i think my son pulled it out too far. How do I take it apart to look at the base of the cord?


A how to take this vacuum has been posted here\015\012\015\012Good luck! ... Miele S318 Bagged Canister Vacuum

Oreck Upright Hi Redev, I'm not sure what model I have (about 6 years old...upright, looks like the one in the picture). I changed the belt (which was torn) and then the next time I used it, it cut off on me. Now if won't turn on at all. (I turn the switch on and off and nothing happens as if it is not plugged in but it is!). I noticed at the top where the power cord enters the handle, it is all frayed. Could the electrical wires have detached? Anything you think I should check before taking it


The cord could be bad and will ahve to be replaced. It would have to have a problem inside the handle or down by the motor. ... Oreck XL2600 Vacuum

I have a Kenmore Progressive model 116.22812204 purchased 2003. The swivel (part nuumber 8195133) that attaches the extension wand to the power mate attachment snapped, so I can't keep the parts connected. I can order a replacement part on-line, but I don't know how to replace it - is it difficult to take apart the power-mate and replace this part? Do you have instructions on how to do it? Thanks!


... Kenmore Vacuums

How do I take the Hoover Spirit canister vacuum apart to unjam the power cord? The cord is stuck and I can't pull it out.


... Vacuums

I have a electrolux 7000 my cord brok off and it got succked in. igot it apart. I DONY KNOW HOW TO PUT THE COIL SPRING ON THE POWER CORD WHEEL. NEED HELP


This is very difficult to reassemble correctly, and more difficult to explain properly. You need to take the vacuum to the nearest authorized Aerus Electrolux store for reassembly. Or call for free pick up and delivery.\015\012\015\012 ... Electrolux Lux 7000 Bagged Canister Vacuum

I bought the Eureka 4703D model vacuum and my very first time powering it on, it was extremely loud - abnormally loud, and I don't know if it is loud like that because I possibly put it together wrong, or there is something wrong with it or it was previously damaged and I would like to know if this is something I can fix myself or do I have to take it back apart and return it to Walmart where I purchased it from. When it makes the loud noise, it does vacuum fine but the noise is just unbearable


... Eureka Power Plus 4703D Bagless Upright Vacuum

How do I take apart my Bissell Cleanview Helix to replace the power cord?


... Bissell Cleanview Helix Vacuum

Repplacing power cord on Hoover Wind tunnel (not self propelled)


I am thinking that the cord goes in on the back, just below the handle. Remove the handle, then from the front, remove the tool holder(#8), then you can get to where the cord comes in and hooks up.\015\012\015\012 ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Took canister apart to replace power cord. some grid fell out before i could see where it was. need to know where it goes


... Oreck BB2000 XL Little Hero Canister Vacuum

I dont have a power cord and or foot pedal and need to know what I need.


Power cords can be found at http://search.totalvac.com/search?keywords=power+cord ... Vacuums

I am trying to replace the power cord for my 82 year old father-in-law's Oreck XL 2600HH. He already took it apart. I need to know where the semi U shaped spring steel piece is supposed to go inside the Helping Hand Handle? Any drawings or schematics available? Thank you for your time. Arthur


That justs lies on the inner handle whenb you put the spring back. There should be two holds where each end of the spring sits in. ... Oreck XL Ultra Bagged Upright Vacuum

Hi I have a eureka 410 series lightweight upright and I took it apart to clean the dust from inside and on the very bottom of the handle the is a metal clip and a white straight plastic peice that fell out and I dont know how it goes back in.


... Eureka Whirlwind 410 Bagless Upright Cyclonic Vacuum

NO POWER TO UNIT.HOW DO I TAKE IT APART? - Kirby G4 Bagged Upright Vacuum


Remove the screw attaching the cord cover to the side of the machine and remove the cover by carefully prying from the rear with a flat screwdriver. Check the cord with a voltmeter. This machine will also not run unless the rug head (or hose), and ba ... Kirby G4 Bagged Upright Vacuum

Handle relase stuck in upright position and I have the vacuum apart and I dont know what to do what am I looking for it is still stuck


Dirtdevil vacuums are so cheap. it's jammed. just go to a vacuum shop and get it repaired ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

I need to take apart my aeg nimble vaccum cleaner to fix power cord


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0798 seconds