Having problems with your Bissell Vacuums ?

I need to put a new belt on the vaccum cleaner,om

\015 I need to put a new belt on the vaccum cleaner,on the bagless vaccum cleaner for pet hair\015

Answers :

You can get any bissell belt you need at www.vacbelts.com
Repair Help & Product Troubleshooting for Bissell Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I need to put a new belt on the vaccum cleaner,om


You can get any bissell belt you need at www.vacbelts.com ... Bissell Vacuums

Oreck vaccum when i put a new belt on, the belt rubs the side of the wall of the vacuum gets real hot and busts. is there any type of washer fitting that goes on the vacuum to hold the belt in place? i dont know i need help thank you. you can reach me at [email protected]


The belt must not be running true to the pulley. You may need a brush roll, but also check the motor to make sure it isn't moving inward after the belt is put on. ... Oreck XL Ultra Bagged Upright Vacuum

D.d vaccum i have a dirt devil dynamite...i bought a new for it i put it on and not even 1 minute of using it the belt broke again!!!!i dont know whats going on do i have 2 put it on a certain way does it need grease or what!


Did you check the brush roll, if the ends aren't turning freely, then it needs to be replaced also. ... Dirt Devil M084600 Dynamite Bagless Upright Vacuum

Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn't seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right....can you help. I am v


I've successfully used a compatible belt - Royal 104425001 .It's still new, but for the time being at least - it works. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

I bought new belts to replace the old ones (one had broken and the water would not feed) My cousin took it apart and now I need to put the new belts on and get it back together - do you have instructions or a diagram?


There are different variations with Bissell. They have the ProHeat series and a Power Turbo series. Below is a link with instructions and diagrams for the Belt Access Door. If this doesn't solve your problem or isn't the correct model, please post ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have a kenmore grab n go bagless and I need to know the exact size of the belt, I lost the manual, and I have burn several belts at the bigining of the problem the motor stops and burn the belts I open it and I think it was a little piece of plastic, that cause the problem, but when I put the new belt it looks like the motor works fine,but still burn the belt, I'm using UB-1 #5275 belt am I using the wrong one?


... Kenmore 34722 Grab-N-Go Upright Vacuum

Schematics I went to replace the belt, and when I put it back on I noticed the silver pulley that the brush belt goes on has came unattached from the red piece by the motor belt. It is one peice. I can order a new pump, but I need the schematics so I can replace the pump. http://www.vacuums24x7.com/bistclpa.html How can I enlarge this so i can read it?


Well you can right click the picture and save it to your desktop, I did it, but it was alittle blurry. But if this doesn't work for you, post me your email addy and I can send you a better picture. But take the top off, there are 6 screws, 3 on ea ... Bissell 8910 ProHeat Clear View Upright Vacuum

How do I put a new belt on Hoover Concept One vaccume cleaner?


You most likely have to remove the cover over the roller, which has screws usually. then you will see the belt. the roller slips out replace the belt by putting it over the roller and a metal rod that is up under the cover you removed. this will be a ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I need to change the belt on the shampooer. the shampooer doesn't come apart like the vaccuum unit. i can't get the brush off so i can put a new one on.


This will help...\015\012\015\012http://reviews.ebay.com/CHANGING-THE-BELT-ON-A-KIRBY-G3-G4 ... Kirby G5 Bagged Upright Vacuum

I just put a new belt on my boss 4800 and it is to loose? Does the beater bar needed to be replaced? There is no traction to turn the belt, it spins


Sounds like the belt is to big you didnt replace with the correct belt ... Eureka Smartvac 4870 Bagged Upright Vacuum

Belt broke how to put new belt on i need manual


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Have a Morphy Richards 1500 watt cyclone Ultra Light vacuum cleaner Model No. 73320. Belt has broken and I have lot the manual. Need instructions as to how to put in a new belt


... Morphy Richards Vacuums

I HAVE A NEW BELT I NEED TO PUT ON MY VACUM CLEANER BUT I CANT FIGURE OUT HOW TO PUT IT ON?


You need to take the bottom cover off to expose the motor's pulley, and the beater bar. take the beater barr off by just pulling it off, and follow the marks on the plastic where the belt goes. ... Dirt Devil Vacuums

Vaccum cleaner needs belt put on and i have belt, but can't figure out where it goes except that it is over the rotator wheel from there i am lost and i have no manual


Wish you had given your model number because they are different. On some, the belt goes over the motor shaft, then over the brush roll. Some you have to remove he top cover to get to the motor shaft. Some go over the motor shaft, then over the big ... Hoover Vacuums

Replace the belt on a Eureka contour model 2900 upright vaccum. I just want to see a picture of the way it comes apart. It a almost new and just needs the belt replaced.


I have listed below a link to the owners manual for your model and a link where you can purchase the belt you need. Hope it helps you!Eureka Contour 2900 ... Vacuums

I need to put a new belt on the Ultra hand vac 8230. How do I get the cover near the belt off?


If you go to this URL:\015\012\015\012http://www.dirtdevil.com/manuals/?id=497300a5-3758-479d-a8e5-0555f40193f0\015\012\015\012you can see the pictorial of what you need to do to change the belt. ... Dirt Devil Ultra MVP Vacuum

Vaccum cleaner, (hoover upright) needs new belt, but i can't figure out where it's located.....yes, i'm a woman...lol thank you..


Turn Vac over, remove the plate covering the brush roll, then you can get to the belt and brushroll. ... Vacuums

I am trying to install new belt. I got the bottom of the vacuum off, but now I need a diagram on how to put it back together.


... Eureka 431A Optima Bagless Upright Vacuum

I can not get the new belt to rotate on my vaccum. The roller will not turn when it is put back in place. Any suggestions?


If by roller you mean the beater brush that the belt is attached to, you might try taking the beater brush out of the unit and clean both ends. There should be some kind of plastic or rubber holders on each end of the beater brush. The brush itself ... Vacuums

Need to put on a new beater bar belt on my dyson 17 animal


Http://www.youtube.com/watch?v=Z1nSYmrLLsE ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The belt broke on the helix bissel vaccum and when I put the new one on the brush does not turn - is that right?


Provided it's the proper belt, perhaps a twist of the belt is needed, as some go straight, others have a 180 degree twist.(like a figure 8) If that doesn't do it, get back with make & model of machine please. ... Bissell Vacuums

We had to take the machine apart just to see that the belt had broken after only 5 use's . We can not see how we are ever going to put the new belt back on. do you have instructions on how to take the belt off and how to put a new one on? Please send me one.


I have a Panasonic MC-V5746 upright vacuum. According to the booklet, \015\012MAKE SURE UNIT IS UNPLUGGED.\015\0121. Place carpet-bare floor selector in "carpet" position.\015\0122. Remove lower plate (there are two screws in the m ... Vacuums

My belt broke...I bought a new belt..but I do not know how to put the new on on. I took out the brush roller and put the belt around it but I have no idea how to get it to go on the part that makes it move.


Hello,\015\012Here is a link to my free online guide...\015\012\015\012http://reviews ... Kirby Ultimate G Bagged Upright Vacuum

Hubby took apart to put a new belt on ,, now he


Go to this site...http://www.youtube.com/watch?v=At7tqnjD-Kc ... Kirby Ultimate G Bagged Upright Vacuum

I am, trying to put a new belt on my hoover and lost my book to it


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1044 seconds