Having problems with your Bissell Vacuums ?

Put brush belt on Bissell 1697M Dirtlifter Powerbrush

Answers :

Hello,please kindly follow the steps below to fix your brush belt for bissell 1697m,

  1. Unplug the vacuum before attempting any maintenance on it to avoid electric shock.
  2. \015\012
  3. \015\012\011\011\011\011\011\011\011\011\015\012Step 2\015\012\011\011\011\011\011\011\011\011\015\012\011\011\011\011\011\011\011\011Place the vacuum handle in the low position and turn it over. The bottom side of the power foot should be facing up.
  4. \015\012
  5. \015\012\011\011\011\011\011\011\011\011\015\012Step 3\015\012\011\011\011\011\011\011\011\011\015\012\011\011\011\011\011\011\011\011Use\015\012the Phillips head screwdriver to remove the four screws on each side of\015\012the brush cover. Set the screws and brush cover aside.
  6. \015\012
  7. \015\012\011\011\011\011\011\011\011\011\015\012Step 4\015\012\011\011\011\011\011\011\011\011\015\012\011\011\011\011\011\011\011\011Pull\015\012out the rotating floor brush by grabbing both ends and lifting it\015\012straight up. You'll notice that the drive belt (it looks like a big\015\012gray rubber band) is looped around one end of the floor brush and the\015\012other end is looped over a pulley inside the vacuum. Take the drive\015\012belt off the brush and the pulley and set it aside for now. If the\015\012drive belt is completely snapped in two, just grab it out.
  8. \015\012
  9. \015\012\011\011\011\011\011\011\011\011\015\012Step 5\015\012\011\011\011\011\011\011\011\011\015\012\011\011\011\011\011\011\011\011Place the new drive belt over the motor pulley and also stretch it over the end of the floor brush.
  10. \015\012
  11. \015\012\011\011\011\011\011\011\011\011\015\012Step 6\015\012\011\011\011\011\011\011\011\011\015\012\011\011\011\011\011\011\011\011Replace\015\012the floor brush by lining up the ends of the brush with the slots. Turn\015\012the brush a few times to get the tension right and force the belt to\015\012center itself on the brush.
  12. \015\012
  13. \015\012\011\011\011\011\011\011\011\011\015\012Step 7\015\012\011\011\011\011\011\011\011\011\015\012\011\011\011\011\011\011\011\011Put the brush cover on with the four screws and press down on it to make sure the brush cover has also snapped into place.
wish you good luck,

take care.

Hi,with the level of job you have done in the process of replacing the brush belt,i think its time you contact a technician to help you out,it won't cost you much compared to the stress you have and will continue to encounter.\015\012
\015\012Thanks and take care
Repair Help & Product Troubleshooting for Bissell Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Put brush belt on Bissell 1697M Dirtlifter Powerbrush

Hello,please kindly follow the steps below to fix your brush belt for bissell 1697m,\015\012\015\012Unplug the vacuum before attempting any maintenance on it to avoid electric shock.\015\012\011\011\011\011\011\ ... Bissell Vacuums

Machine will not pump out water. Brushes work, motor works, new belt, Just will not put out any water??? It is a Bissell Powersteamer,Clearview 4 row brush , dirtlifter.

IF you take the tank out of the base you will see a recepticle where the tank nipple fits into the base. There is a cross looking pattern in the recepticle. Take a pointy object and press down inside the cross area between the bars in the little pie ... Vacuums

I have a Bissell proheat clearview 12 amp 5 cleaning rows of dirtlifter powerbrush. It won't shoot the cleaner to the brushes. I cleaned the filter, checked the belt, water is full, and soap dispenser is full. Still no soap going to rug. Can you help? Thanks

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc

... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o

Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a bissell 9300 carpet shampooer..the belt broke o n the left side. tookoff the plasitc brush shield to access the area to put on the belt but not sure how to connect it to both brushes..only one comes undone...do i have to unscreww the whole thing?

Follow the link below on how to change the belt.\015\012http://www.bissell.com/VideoRating.aspx?id=1557 ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Bissell Dirtlifter Powerbrush carpet cleaner will not roll. The back wheels roll fine, but when you put the machine down flat, the front part (where the roller is) sticks and will not roll.

I had the same problem. It would pull backwards but not go forward. A closer examination revealed the clear plastic part on the bottom in the very front of the machine had popped loose on one side. If you look at the front of the machine, th ... Vacuums

Brushes run freely on the cog and I put on 2 new belts and new brushes on my Bissell Proheatx2 the brushes do not turn when the machine is running even if I have the handle in the relesed position

I know how frustrating it can be when the brushes don't turn when you're ready to clean.Here's a quick link to troubleshooting steps to assist you:\015\012 ... Bissell Vacuums

I have a Bissell quicksteamer powerbrush steam cleaner. The power brush will not spin but the motor works to rotate it. I went to purchase a new belt but the guy told me the belt was fine? Any other suggestions?

... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I replaced the belt on my bissell model number 3576-2, but when i put it back together, the brushes wont move...the belt tries to move, but the rubber just burns..

Something is binding ... i dont know what ... you will have to remove all parts and reinstall again. Make sure the bearings spin on the brush when it is out ... remove all hair and string.\015\012\015\012good luck ... im sure it is some ... Bissell 6595 Lift Off Bagless Upright Vacuum

We have the pet steam cleaner bissell 12 amp, we tried cleaning off the brush, because the cleaner wasnt sucking up the water sufficently. a screw came out along with the belt roller, and we have no idea how to put the screw or the belt back on.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have a Bissell Powersteamer Pro Deluxe, Model 8804 shampooer. I got this bright idea to take the brush off as it was full of hair and debree. Upon putting it back on it appears I'm not getting the brush on properly. Does the belt go around the end with the grooves? Also do the grooves go on the right or left side? From my view point I am looking at the machine with it lying on it's back and I am sitting on the floor looking at the bottom of machine. Sure hope I haven't confused you too m

... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

How do i put belts on a bissell powerbrush steam cleaner?

If this is the model i'm thinking of. Make sure the units unplugged from the wall. There should be about six phillips head screws to remove. The motor should now be exposed. This is a good time to clean up the inside of the unit. Use liquid wrench or ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

The belt broke on the helix bissel vaccum and when I put the new one on the brush does not turn - is that right?

Provided it's the proper belt, perhaps a twist of the belt is needed, as some go straight, others have a 180 degree twist.(like a figure 8) If that doesn't do it, get back with make & model of machine please. ... Bissell Vacuums

I have a Bissell cleanview revolution deluxe model # 53F8. How do I put the brush bar and belt back on??

... Bissell 8975 CleanView Bagless Upright Vacuum

I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.

... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a

... Bissell ProHeat Deep Cleaner Upright Vacuum

For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.

... Kirby Ultimate G Bagged Upright Vacuum

The gear that turns the dual brushes on my Bissell Spot Lifter 1716 seems to be stripped. The belt looks loose as well, but when I take the belt cover and the brush assembly out, the gear that turns the brushes is loose and appears to be stripped on the cogs. When I turn the machine on the belt turns the gear but the brushes just sit there an vibrate. They make an attempt to turn now and then but not much. Need to get a schematic or the parts so I can order the gear if it is available and th

... Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn

Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

Vax 2300 vax v-2300 brush is not turning so changed belt snapped as soon as i put hoover on and getting burning smell put another belt on same again and brushes still not moving only 4 months old

If the roller brush cannot be rotated easily by hand, it is likely that debris is jammed inside the end caps.Make note of the direction arrows on the end caps as you remove the roller brush. You will need to know this for reinstallation. The end caps ... Vacuums

Cannot figure out how to install brush belt on a bissell proheat

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

Bissell bagless 6583 brush won't turn after new belt

Sorry to hear about the difficulty with the brush. If your brush does not turn by hand freely, then your brush needs to be replaced. Here is a quick link to order a new brush: \015\012 ... Vacuums

Need to replace the brush belt on Bissell Proheat Pet Model 8910

... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Replaces the belt on dirt devil dynamite pluse model put everything back together started it and it burt the new belt up that fast. I put it around the beater brush and the metal bar I thought it should go around, yet it seemed like there should be something else there to put the belt on. What do you suggest? Do you have picture I could go by?

The metal bar you put it around if the bar itself does not spin it is going to burn the belt up. Every thing that the belt is supposed to go around has to turn or the belt will rub on the piece not moving and brake. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0764 seconds