Having problems with your Bissell Vacuums ?

My 2X Bissell carpet cleaner is not sucking the water back up after dispensing. I do not have any dirty water collected around the bladder. How do I fix that?


Answers :

If the carpet cleaner is not sucking any water, nine times out of ten, the culprit is the lid on the lower recovery tank. The lid on the lower tank (or dirty water tank) needs to hinge at the front and snap down at the back in order to create a proper seal. If the lid snaps on but is not locked on at the front, you will not get any suction. Simply take the lid off, and ensure that when you put it back on, it must hinge on the front tabs of the tank.If lid is properly closed then,\015\012
check out the filter and the hose.\012
if the filter or the hose is got blocked the water will not get its pressure to return and it will not return to the upper section.
clean the filter and hose with normal tap water then reconnect it and check.If still the same problem then it needs to be replaced.
\015\012\015\012Thanks. Keep updated for any more query. You can rate this\015\012solution and show your appreciation.
Hello,\012

The problem might be caused by any of these four sources listed below;
1.  Ready tool dial may be at wrong settings.
The solution to that is for you to set ready tool dial to either floor cleaning or hose attachment setting.

2.  The tank may not be seated properly.
The solution to that is for you to pick up both the water tank and the solution tank and reseat them so they fit snugly to the unit.

3. The solution or water tank is empty.
The solution to that is for you to check fluid levels in heavy duty bladder and formula tank.

4.  2-in-1 tank has picked up maximum dirty water.
The solution is for you to empty the 2-in-1 tank and refill with clean hot tap water into the heavy duty bladder.

Take care 
Repair Help & Product Troubleshooting for Bissell Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My 2X Bissell carpet cleaner is not sucking the water back up after dispensing. I do not have any dirty water collected around the bladder. How do I fix that?


If the carpet cleaner is not sucking any water, nine times out of ten, the culprit is the lid on the lower recovery tank. The lid on the lower tank (or dirty water tank) needs to hinge at the front and snap down at the back in order to cr ... Bissell Vacuums

Does the dirty water go into the bladder? I thought that the bladder was the holding tank for dirty water. Any water (very little) was collected and sat on top of bladder. Any advise is appreciated


... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Have a new pro heat 2x. seems to work well but does not seem to extract water. It has the two in one reservoir and there is no dirty water around the clean water bladder. What is the problem?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My recovery tank is not collecting dirty water need answer on how to fix it? Thanks


Hoover carpet cleaner does not pick up water ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet


Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn't blocked as well. ... Vacuums

My bissell steam cleaner Model #9200P purchased 12/12/12 and only used once does not soak up the dirty water from the carpet. The bladder dispenses water and the solution is dispensed but the dirty w


Hi Barbara. I understand how frustrating no suction can be when you're trying to clean. Here's a quick link to troubleshooting steps to assist you: \015\012 ... Bissell 2X Proheat 9200 rug cleaner

Little green machine pro heat pet the collection tank wasn't collection and dirty water was coming out of the bottom. i took it apart, cleaned it up and put a new "duckbill" gasket in. then it quit spraying, but i think i got that working again. now after i spray and get a good foam on the carpet, i switch to suction and it seems very weak. i can see the water moving (trickling) from the head into the hose but it is not reaching the collection tank -- actually, i am not sure where its goin


... Bissell THE BISSELL LITTLE GREEN MACHINE Vacuum

Vax is dispensing from clean water tank but dirty water tank is not collecting anything


... Vacuums

Hoover SteamVac Model F6056-900 SteamVac/SpinScrub. Indicator light and high pitch suction noise indicates that dirty water tank is full. However, water level indicator (yellow bobbing plastic thing) is at the bottom of the tank and there is no water in the tank. Have check all the hoses for clogs, none found. Checked water port from motor area to receptacle tank for clogs, none found. Fixed broken hose to upholstery wand with duck tape, (wire not broken, just cracked plastic hose). The onl


There are 2 filters, make sure they are clean, one is on the tank lid, the other is from the bottom, it is red, pull it out and clean it. If yours has a foam filter on the tank lid covering the yellow ball, make sure there is at least a 1/4 in. gap ... Hoover Vacuums

I have a bissell proheat 2x and it leaks water around the wheel it holds dirty water but doesnt hold clean water.......and how do i remove the wheel on my bissell


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have the Bissell 2x proheat. There is no water being sucked up from the bladder and the cleaning solution is not being sucked in either in order to get to the carpet. On water rinse the carpet gets wet but I'm not seeing any water going through the clear front piece. I live in Harvest Alabama. Where can I take it to get fixed if it needs it?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

No dirty water in the collection tank. It sucks up the water, but it seems to be leaking back out


... Bissell 2X Proheat 9200 rug cleaner

Why is there no water collection in the dirty water holder?


First make sure the unit is dispensing water, if so then check to make sure the lis on the lower tank is snapped on properly and that the front duct panel is installed. the front panel duct MUST be installed for floor operation to extract the solutio ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

The dirty water is now mixing with the clean water in the bladder, what is the likely cause?


The thing you fill up has a hole in it leting them mix together or vice versa ... Vacuums

Cant locate owners manuel for bissell proheat complete pet 2x does solution go in small tank and hot water in bottom tank ?????where does dirty water collect ??


... Vacuums

Tank not collecting dirty water


You most likely have a break in your suction hose. check at the base where it attaches. When you bring back the handle release, you can see lt. If you have the type that has the external plug in for the water, then you probably don't have the hose ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Suction button Although my Hoover Spin scrub is working perfecting dispensing the solution, when I go to suck up the solution from the carpet--I am having problems with the RED suction button that keeps popping up. I have to stop the cleaner and lift up the dirty water container to break the suction. Ive tried cleaning the netting that is encased around it, but still no luck. Any help would be appreciated! Thanks


This happens when the filter on the inside of the lid for the dirty water tank is pushed all of the way up. You need to leave a 1/4 in. gap from the top to the top of the filter ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Not spraying or collecting dirty water


It may be the pump thats blocked or needs replacing this video will show you how to dissasemble the machine..http://www.youtube.com/w ... Bissell 12005 Spot Bot Handheld Vacuum

Floormate Spinbrush The water comes out fine to clean but when I out it on the wet pickup setting, it piskc up in streaks and it has the most horrible sound while moving it around, like the rubber is going across the floor dry. Any solutions or anyone with similiar problems and a fix?


Not sure if this will help but these machines are ment to be used in one direction not back and forth like a vacuum cleaner. You should start in one spot and pull towards you slowly with the trigger depressed it is designed ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

My bissell keeps collecting the dirt above the emptying cup. gets clogged around the hole under the brush also. how can I fix this?


... Bissell 3576 CleanView II Bagless Upright Vacuum

My Hoover SteamVac has been doing a wonderful job but in two instances, after emptying the dirty water and reattaching the reservoir, the machine has lost suction. The first time I was able to make it work again after taking it apart and putting it back together about 10 times. I don't know what I did that fixed it but as long as it worked again, I was happy. But it's happened again and I can't get it to vacuum. I can see that it isn't clogged. Can you please help me????


Look for the lower tank filter to be clean. also make sure the lower tank lid is on properly. latch when installed on machine. Make sure the front panel duct is on the lower tank. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I used the Scooba 390 for the first time this weekend and it seems that the robot had problem sucking up the dirty water from the floor. When I emptied the dirty water tank, there was hardly any dirty water. Can you please let me know what can cause this problem?


... Roomba iRobot Scooba 390 Floor Washing Robot

My bissell pro heat does not **** up the dirty water anymore at least the dirty water tank does not fill with dirty water


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

The cleaner/water solution dispenses into the carpet, cleans it, pulls out the pet hair, but no dirty water goes into the dirty water reservoir! is all this dirty water going into my carpet?


The pet hair may be clogging the water return inlet I suugest you clean the bushes and inlet as well ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Bissell Steam Cleaner that is not sucking up the water when cleaning. I used a full container of water and when it was empty I emptied out the water, only to find very little dirty water in it. I noticed the window, as i used it, seemed like it wasnt sucking up the water. I took the plastic cover off to clean it (it didnt look very dirty in the first place), an i noticed that the grey plastic flap was on but not moving up or down. I thought there may be dirt in it that prevented it from


... Bissell Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0471 seconds