Having problems with your Bissell Vacuums ?

Dont remember how to put vacuum belt on - Bissell Vacuums

Answers :


Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem.

Bissell Proheat Upright Wet/Dry Vacuum Problems

Repair Help & Product Troubleshooting for Bissell Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dont remember how to put vacuum belt on - Bissell Vacuums

Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem.B ... Bissell Vacuums

The belt on my vacuum cleaner model 6596 bissel powerforce bagless turbo keeps breaking. As soon as I put on a new belt and start it up the belt snaps. It is the durabelt meant for this vacuum model. Also, my son has been having the same problem with his. He has the same model and same belt. This problem is occurring even after a thourough cleaning.

I would guess you aren't centering the belt correctly, thus it's edge is caught between the brush and another solid object, causing the breakage.\015\012When you get the belt on the the brush and the brush back in place, turn the brush a few ti ... Bissell 6596 Bagless Upright Vacuum

Oreck vaccum when i put a new belt on, the belt rubs the side of the wall of the vacuum gets real hot and busts. is there any type of washer fitting that goes on the vacuum to hold the belt in place? i dont know i need help thank you. you can reach me at [email protected]

The belt must not be running true to the pulley. You may need a brush roll, but also check the motor to make sure it isn't moving inward after the belt is put on. ... Oreck XL Ultra Bagged Upright Vacuum

Bissell cleanview 11 bagless special edition model 3576-2 I took apart to clean the filters and don't remember howto put the bottom of the dirt container back. I thought I put the empty container back in place correctly but the dirt when vacuuming is flowing through another part of the vacuum.

... Bissell Vacuums

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc

... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I took apart my bissell easy vac to clean it because it was clogged and now I cannot remember how a part goes on that is underneith the vacuum. I keep putting it on but its not right. It lifts the vacuum off the floor so it is not sitting in there right.

Make sure the plate is lined up correctly it should side down flush ... Vacuums

Belt broke I have a bissell powersteamer and a belt broke and came out the bottom of it. I dont know how to put one back on it

There should be an access panel on the top side of the cleaner. Pry this open with a screw driver and this should get you access to the area where the belt can be changed. ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

Hey i have a eureka 2971 BVZ upright vacuum cleaner and after removing the old belt to replace it. I accidently removed the Guard Belt and i can't remember how to put it back on.

... Eureka 2961AVZ Bagless Upright Vacuum

Belt I have a bissell pro heat model number7901-1 and i dont know how to put the belt back on. The old one broke and i cant find my book.

First take off the cover on the left side of the top cover, then turn it over, remove the screw holding the red lock and pull the cap and brush roll out, remove the cap, remove the cogged belt, then you can put the new pump belt thru that slot, put o ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

How to put a belt on - Bissell PowerSteamer Deep Cleaner Plum Upright Vacuum

Follow the link below to watch a How To Video on how to change the belts.\012http://www.bissell.com/VideoRating.aspx?id=1555 ... Bissell PowerSteamer Deep Cleaner Plum Upright Vacuum

How do i put new belt on - Bissell 7901-R Clearview Proheat Plus Upright Vacuum

How do I change on my Bissell Proheat Clearview Model # 1699-W ... Bissell 7901-R Clearview Proheat Plus Upright Vacuum

I just used my Bissell Proheat, when I heard the vacuum sound get lower and lower then suddenly something "gave" and it got very loud and started emitting a burnt rubber smell. It still worked to put liquid into the carpet; seemed to have trouble getting it out. I checked the tank, filters, belt, and roller and all seemed OK - but when I started up again and looked down I saw sparks in the motor/belt area and shut it down immediately. Any thoughts?

The bearing that is located at the top of the vacuum motor has failed . Because of that the shaft of the motor's rotor is out of position and the pulley attached to it has started rubbing on the other pulleys, giving you that smell. the spark appear ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

How do you put a belt on abissell easy vac - Bissell 3102-0 EasyVac Upright Vacuum

Hi,\015\012\015\012This line will take you there.\015\012\015\012http://middleeasten.bissell.com/images/UserGuides/3108.pdf ... Bissell 3102-0 EasyVac Upright Vacuum

I took apart the belts on my bissell turbo proheat awhile back. now i don't remember how to put it back together.

Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem.B ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

How do you put a belt on the bissell momentum cyclonic vacuum cleaner

Follow the link below for a BISSELL vacuum belt installation.\012http://www.bissell.com/VideoRating.aspx?id=1556 ... Bissell Vacuum - Momentum Cyclonic 1 ea Bagless Upright Vacuum

I have two old identical 5842's that I use in the garage and around the house. The belt broke on one so I bought a bag of 2 genuine Eurika "U" belts, which is the correct belt for this vacuum. They were obviously smaller than the original belt because they were not stretched out. When I put the new belt on it lasted about 20 minutes and then came off. I put it back on and ran the vacuum with the cover off to see what was wrong. Everything looked fine except the belt rides to the outside edge of

Not 100% sure this is the remedy for that particular problem, but I would take the time to clean both of the brushes that the belts operate, one on each machine.\015\012Remove the brushes and clean as best you can. At the end of each brush there sho ... Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum

I have a kirby sentria. vacuumed up my son's headphones and immediately shut if off. took brush off, unwound headphones, put it back together. when i turned it back on, the belt snapped. so i went to vacuum place, got new belt, but when i put it on, with the green arrows lined up, it doesn't have much suction. with the red arrows lined up, it just smells like its burning and i don't want to break another belt! HELP!!

Take the front off the vacuum and check inside both the front portion and the canister for additonal clogs. Sometimes something will get caught in the impellor, causing the motor to overheat. Since there's little suction and the smell, I'd guess th ... Kirby Generation 3 Bagged Upright Vacuum

I have a Eureka 4800 series the Boss upright with a bag and Hepa filter. I love it! I was just vacuuming with the hose part and all was well and then suddenly the lower brush came on and a "burning" smell followed. Thought it was the belt so my husband was going to put on the new belt which I had on hand! When he turned it over, the "bar" that holds the belt looks as though it "shot through" the plastic side of the housing on the vacuum. There is melted plastic on the outside of the vacuum and o

I had the same problem. Take out the old belt if possible. Remove the 4 screws inside the filter and the 3 on the front of that housing. pull out the foam around the motor. carefully pull out the suction tube that is press fit against the motor. ... Eureka 4874 Bagged Upright Vacuum

For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.

... Kirby Ultimate G Bagged Upright Vacuum

I replaced my Bissell vacuum cleaner belt with a Bissell belt. I ordered it from them so I know it's the right one. I replaced it and the roller won't spin and the belt smells like it burning.

Beckiande485: You will need to unplug the vacuum from the wall, lay it down so you can see the bottom of the vacuum head and remove the bottom plate (foot plate) Probably philllips head screws. pull up on the roller (called the beater bar). ... Bissell Vacuums

Is there a diagram/picture to help me visualize how to put cleaner belt back in vacuum? I was taking base of vacuum apart so I could get rid of hair that were wrapped on the roller. The cleaner belt came to loose and I could not figure how to fix it back. the model is eureka upright bagless series 430

Hi,Sorry to hear your belt fell out. Not good if you've never replaced a belt before...Here is a website where you can read a detailed description of how to change a belt: http://www.ehow.com/how_8034505_eureka-belt-replacemen ... Eureka 431A Optima Bagless Upright Vacuum

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.

... Windsor VS14 Versamatic Bagged Upright Vacuum

How to change belt on Bissell 6582 vacuum - Bissell 6594 PowerForce Bagless Upright Vacuum

Here is a link to the belts you need and to a manual you can view with instructions.Bissell PowerForce Belts and ManualHope it helps ... Bissell 6594 PowerForce Bagless Upright Vacuum

Vacuum belts how do i put a new belt on my vacuum?

I can't do it ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My oreck upright smells like rubber burning when i vacuum. i just put a new belt on but it smelled like that before i even put the belt on

... Oreck XL Ultra Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1296 seconds