Having problems with your Bissell Vacuums ?
My bissel vacuum 2x cyclonic action cleaner item #3920 rubber drive belt broke and there isn't any suction.
If you go to this URL\015\012http://www.bissell.com/assets/0/132/134/228/e5babada-7240-40ea-93c0-90427ed32741.pdf\015\012You will find the users manual that describes what to do to replace the belt.\015\012I suggest that when you remove the brush, clean it as best you can, paying special attention to the plastic clips on each end. I would spray some WD40 between the clips and the brush and turn the clips until they move freely.\015\012If you find my solution to be of help to you, I would appreciate a Thumbs Up from you.\015\012Paul
Repair Help & Product Troubleshooting for Bissell Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
My bissel vacuum 2x cyclonic action cleaner item #3920 rubber drive belt broke and there isn't any suction.
If you go to this URL\015\012http://www.bissell.com/assets/0/132/134/228/e5babada-7240-40ea-93c0-90427ed32741.pdf\015\012You will find the users manual that describes what to do to replace the belt.\015\012I suggest that when you remove the brush, cl ... Bissell Vacuums
The Panasonic MC-V7515 has two belts. The local vacuum repair guy says he only has a part number for the drive belt, which is UB-9. How do I find a replacement for the other belt, the one which directly drives the beater bars? By the way, this vacuum has great suction, but otherwise is far inferior to my previous Panasonic vacuums. The cheaper models aren't a good buy--stick with the more expensive models.
... Panasonic MC-V7515 Bagged Upright Vacuum
I have a Zanussi 1700W bagless upright vacuum cleaner which keeps cutting out after about 5/10 mins use. I had to replace the rubber drive belt which snapped not long after purchasing and it was fine for a while, but now its just keeps cutting out after a small amount of use. Nothing wrong with belt which is still intact so we don't know what the problem is. It's a great cleaner otherwise - but it's driving us mad!! Please help!
Bag was not on good, resulted in dust,dirt, dog hair everywhere...have cleaned pretty thoroughly but vacuum does not have any suction. After taking apart did find that the larger wide belt is broke but I think that just affects the self propel...is there a belt tied to suction? HELP!
Greetings from GoVacuum,\015\012\015\012There are two things that you should check on this vacuum after running it without a bag inside. The first thing you should check is the filter that is underneath of the vacuum bag. This filter i ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Powerhead woes Drive belt for power head beater brush on Hoover S3755 keeps jumping off drive motor shaft when vacuuming low pile carpets like oriental rugs unless minimal suction is used. Any tricks to keeping the belt in place other than this?
I've had my Hoover S3755 for about 2 years and loved it, at least until the last couple of months when the "belt slipping off" problem started. I changed the belt and the vacuum would work for a little while then the belt would come off again. I pu ... Hoover S3755 WindTunnel Bagless Canister Vacuum
Belt problem My belt broke. I put a new belt in, followed the instructions, seemed to be right but as I started using the vaccuum, it starting smelling like burnt rubber. The belt was extremely hot. Took it apart, tried again and the same thing happened. Please help me!!!!
Get the old lady to use a dustpan and brush instead SORTED ... Kirby Generation 3 Bagged Upright Vacuum
Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the
... Dirt Devil M088905 Vision Bagless Upright Vacuum
Belts I have recently bought new belts and when I installed the green light only comes on sometimes and I can smell rubber burning. The last belt broke very quickly so I am assuming that when I put the vacuum back together I am doing something incorrectly. Can you help instruct me?
Recently received a kirby from mother in law and don't how to change the belts ... Kirby Ultimate G Bagged Upright Vacuum
No suction hello, there was a rubber smell then no suction. i'm thinking it needs a new belt but don't know how to remove the cover to replace. is it a complicated procedure. is there a diagram available? don't have any info here. thanks, leslie
Flip the machine upside down and remove the four screws from the baseplate. Replacement should be fairly self-explanatory from there. If it's a self-propel model, note that the v-belt in the front WILL look loose normally, so it does not usually requ ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
My Fantom Vacum Cyclone et was smoking and smelled of rubber burning. I'm sure it is the belt but I don't know how to get into the vacuum to see the belt.
To replace the belt, Remove the covers over the headlights and under the shiny foul. there are two screws. (In other words: Remove the lens covers, bulbs and the foil. under the foil are two screws.) Then, there are two tabs that hold do ... Fantom Vacums Cyclone XT Upright Vacuum
I have a Kirby Heritage II which normally works amazingly well, but it's not playing at all nicely today - and of course we have apartment inspections tomorrow. *dies* The belt broke today (as did the replacement belt, which I'd bought at the same time, so apparently the rubber was old), so I went over to Stark's to get some new ones - but it still won't cooperate. I've taken the head apart and put it back together several times, to be sure that everything is properly seated, but it's just not
... Kirby Heritage II Vacuum
Belt tightener broke....belt wont stay on - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Belt replacement Hello, The belt that drives the beater bar on my Dyson DC-07 just broke. Is it that difficult to replace it or should I take it somewhere. Thanks!
It's a fairly simple job. The belt just loops over the end of the beater bar and motor shaft. Need to take the cover off the beater bar housing to get to it. Most difficult part is stretching the belt while putting the beater bar back in the housi ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
I just bought a new belt, put it on, took two swipes, smelled burnt rubber again. My new belt broke. Why?
The beater bar is probably not turning. It get's jammed up with hair and strings and Christmas icicles and anything else on the floor. Taking the bar out and cutting all the stuff off is the easiest way to clear it. Make sure it turns freely before y ... Eureka 2961AVZ Bagless Upright Vacuum
I need instructions on replacing the belt that drives the brushes on a Bissell powersteamer pro deluxe carpet cleaner. Could the broken belt have anything to do with the suction of the cleaner?
Here is a link to the belts you need and a link to the manual:Bissell 1697-7 Manual and Replacement Belts ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum
No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.
Generally, the problem is that the belt is not running the brushes. This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed. This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
I have a power drive baggless vacuum cleaner...it runs well, but suddenly it seems to have lost most of the suction coming through the hose and floor area. When I remove the dirt container, the suction below it seems strong. I have had it to repair twice--they have tuned it up and replaced all filters and belt. It still does not pick up well when I vacuum or use the hose. Can you help ?
There is something stopping it up,you will have to dissasemble the unit to find the blockage,this is the most likely problem. ... Hoover U6660-900 WindTunnel Bagless Upright Vacuum
Brushbar not rotating but vacuum has suction - belt not broke
At the point where the shroud is around the drive belt of the motor there is a screw that has to be remeoved. It is accessible through a hole in the housing that is inset about 3 1/2 inches. Once this is removed along with the 2 screws at the base ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Kenmore progressive model 38812790 smelled like rubber burning then the brushes stopped turning. Does it have a belt, if so, how do I get to broken belt to replace?
... Kenmore Vacuums
What is the size of the drive belt and where can I source one from for the Bush Cyclonic Hoover DD9504B? Thanks steve
HOW TO CHANGE DRIVE BELT NO SUCTION FROM UNDERNEATH
The drive belt only controls the beater bar if the bar is spinning the belt is fine.the no suction problem is probably caused by an obstruction in the line , the most common place that this occurs is where the handle pivots from the power head, ... Vacuums
Spare drive belt for Elitech 2000W dual cyclone vacuum cleaner
Replacing clutch drive belt dyson dc14 - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Chris,\015\012I am just trying to find an owners manual, but I can not find one anywhere. Your link did not work. Can you help with another link? ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
The belt broke - Dyson DC07 Bagless Upright Cyclonic Vacuum
You need to replace it with a new one. Here is a link for the instructions on how to change the belt and a link for the belt you need:DC07 Belt Changing Instructions ... Dyson DC07 Bagless Upright Cyclonic Vacuum
The beater bar on my Dyson won't turn. The vacuum runs and suctions but the bar won't turn and the belt is not broke. The beater bar did get a carpet fiber caught and wrapped around it which stopped the bar and I removed the bar to cut the fiber loose and replaced it and now it won't turn
The belt doesn't have to be broken to make the vacuum not work correctly. If the belt is stretched the vacuum won't operate the way it is supposed to. You can get replacement Dyson Belts here: ... Vacuums