Having problems with your Bissell Vacuums ?

I have a Bissell ProHeat 2x, and I did something dum. I had some powdered cleaner that said it works with carpet cleaners-well I mixed it in-and the next time I tried to use it, nothing came out. So, I took it part to check what was wrong-and found out that the powdered cleaner solidified in places. I cleared the nozzels, nothing. I think the solenoid, between the heater and nozzels is pluggd, and possibly the heater. I've got a question-could I use CLR to clean the heater, with replacing t


Answers :

Heck yeah, give it a shot. Try running some water through it too- fill it up, heat it just to where it's hot and unplug it, shake it around and dump it out. Repeat. You might have to get a wire or something to go through and get the powder loosened between the boiler and nozzle, but if the stuff will dissolve in hot water then once you get it going a little it'll flow better the longer you keep heating it and putting new water it.

I say I think you should unplug it once it gets mildly hot the first few times because if there is a pile of the powder stuck to the side of the tank you may find that the tank gets very hot there and overheats/fails.

You should be able to clean the solenoid too, hot water is your friend.

lp
Repair Help & Product Troubleshooting for Bissell Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Bissell ProHeat 2x, and I did something dum. I had some powdered cleaner that said it works with carpet cleaners-well I mixed it in-and the next time I tried to use it, nothing came out. So, I took it part to check what was wrong-and found out that the powdered cleaner solidified in places. I cleared the nozzels, nothing. I think the solenoid, between the heater and nozzels is pluggd, and possibly the heater. I've got a question-could I use CLR to clean the heater, with replacing t


Heck yeah, give it a shot. Try running some water through it too- fill it up, heat it just to where it's hot and unplug it, shake it around and dump it out. Repeat. You might have to get a wire or something to go through and get the powder loosened b ... Bissell Vacuums

Bissell lift off vacuum about 4yrs old. Extremely noisy. OK until before Christmas but getting worse every time it's used. Washable filters washed, HEPA filter replaced. brush bar cleaned of every scrap, hose empty,everything that can be cleared has been. Noise high pitched, screeching and can only bear to use it for a few seconds at a time. Suction OK. Mine is so loud I can't use it very long-high pitch screech. Can this be fixed or does the whole vacuum need to be replaced? It still cleans gr


Sounds like a bad motor. Could be either foot motor or main motor either way cost will be more than half of the unit. ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Last year my wife and I bought a new Dirt Devil Reaction All Surface vaccuum cleaner to replace the older Platinum Force. After using it a couple of times the new one gets clogged with dog hair easily and shuts down. I cleaned it out completely including the hepa filter but it will not handle the dog hair. The old one never had a problem and still works. We went back to using the old vaccuum cleaner because we can not find the receipt and had not registered the new one and are stuck with a new 1


Greetings jettin_us,\015\012\015\012Normally you can contact the store you purchased the unit at, and if you paid with anything other than cash, they may be able to retrieve your receipt for you. \015\012\015\012Once you get t ... Vacuums

I purchased a Pro Heat self propelled Bissell rug cleaner model 7950 from Target wherehouse on 4-26-06. I used it once and all was fine. The next time that I went to use it the smart mix for the cleaning formula would not dispense formula.I called Bissell consumer services and was told to take it to Starks Vaccumn in Sherwood, Or. That was on 10-30-06 They said that it was working so I tried it again and not a drop of formula was or has been used since.I took it back 2-13-07 and the replaced the


I assume that it is spraying water? Is the smart mix knob turning freely from one point to the end? If not then there is a problem with the smart mix asm. With liquid in the soap bottle, push the valve in to see if liquid comes out ok, couild be ... Vacuums

Bissell lift off vacuum about 4yrs old. Extremely noisy. OK until before Christmas but getting worse every time it's used. Washable filters washed, HEPA filter replaced. brush bar cleaned of every scrap, hose empty,everything that can be cleared has been. Noise high pitched, screeching and can only bear to use it for a few seconds at a time. Suction OK.


Sounds like a bad motor bearing. If it is, then you would have to replace it. Could be the brush roll, did you check the ends to make sure they turn easily? ... Vacuums

My bissell proheat 2x carpet cleaner is not spraying from the bottom or sucking up when turned on. The hand tool works just fine. I have made sure it was on floor cleaning when I used it to try and clean my carpet. the busshes are working but nothing else is happening this cleaner is about 21/2 years old and has only been used maybe 5 times so it has not had alot of use.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My vacuum will not pick up anything....likely due to carpet cleaner powder used.


... Dyson DC25 All Floors Bagless Upright Vacuum

I have a Hoover SteamVac SpinScrub with Clean Surge Carpet Cleaner. I loaned the cleaner to my son, who lives 3 hours away from me. My son returned the Steam Cleaner to me on Easter Sunday. My son failed to return the Owner's Manual. I need to clean my ottoman. I have never used the upholstery & stair cleaning tool. Would you be able to e-mail me the instructions for this chore? My e-mail address is: [email protected] My name is Kay. Thank you!


Hi,I would be glad to send that. But, you never Mention the Model Number and there are Various Models introduced by Hoover.Let me know the Manual and within Few Minutes, i would be able to send you one more email which would h ... Vacuums

I have an older model F6056-900 Hoover steamvac Spin Scrub Cleaner. My first problem was that I loaned it out to a friend. Anyway she ran over the hose (used for attachments) with her car. I tried using the cleaner for carpet cleaning this morning but when I tried to put the solution tank into place...its loose...won't snap back in like it used to. When I can get it somewhat in place the solution just complete drains out through the bottom fo the tank. The leak is where the small hole on the bot


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

My carpet cleaner (bissell proheat plus) is not steaming, dispensing cleaner. Seems like there's a little thingy that should be spinning or turning..... When I work a small area of carpet, it just leaves behind dry blobs of carpet gunk like pet hair. I had to use a carpet sweeper to clean up. FYI - I filled the cleaning fluid container and after trying to clean the carpet, it did empty out but the carpet isn't wet. Any tips? The manual doesn't help.


You need to replace the pump belt. Here is the belt you need:Bissell ProHeat Belt ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Steam cleaner im using my cleaner have it all working but it just seems like its not cleaning right!!! i went over it for about 20 min and it has only cleaned a little of the stain am i doing something wrong or does it just take a very long time to clean!!


If it is spraying ok and the brushes are turning, then maybe the cleaner isn't strong enough for the typa of stain you are trying to clean. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have excellent suction power through the vac, but when I try to use the hose there is no suction power there. I have cleaned everything and it is definitely clean and clear. I've also used the reset button.


When you use the upright Dyson, the handle has to be in the upright position for the hose to work. In this position, there should be a clear way through for the suction to the hose, and the suction for the normal sweeper should be off. This is all ... Sharper Image Dyson Slim DC18 All Floors Vacuum

Do you have to use kirby cleaning solutions or can you use another form of carpet cleaner to clean and shampoo my carpet?


You should always use Kirby Shampoo.Other shampoos have abrasives in them,which could clog the tank,or ruin the bearings at the end of brushroll. ... Kirby Vacuums

I have a Bissell Steam Cleaner that is not sucking up the water when cleaning. I used a full container of water and when it was empty I emptied out the water, only to find very little dirty water in it. I noticed the window, as i used it, seemed like it wasnt sucking up the water. I took the plastic cover off to clean it (it didnt look very dirty in the first place), an i noticed that the grey plastic flap was on but not moving up or down. I thought there may be dirt in it that prevented it from


... Bissell Vacuums

My bissel has a upolsty cleaner on it, I used it to clean my couch then shut it off to emty then went to clean the other couch now it wont spray cleaner or ****? can anyone help me?


Things to look at...\015\012\015\012Tank is properly seated (remove and reinstall)\015\012Tools are selected (not floors)\015\012ensure the handle is in the full upri ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Bissell powersteamer powerbrush that sprays for only a few seconds then stops. If I wait 20 seconds or so it will spray again for another 1 or 2 seconds. I have only used Bissell cleaning products in it and clean it every time after use. The hot water tank and cleaner tank are full.


... Bissell Vacuums

I have a Zanussi 1700W bagless upright vacuum cleaner which keeps cutting out after about 5/10 mins use. I had to replace the rubber drive belt which snapped not long after purchasing and it was fine for a while, but now its just keeps cutting out after a small amount of use. Nothing wrong with belt which is still intact so we don't know what the problem is. It's a great cleaner otherwise - but it's driving us mad!! Please help!


... Vacuums

Hoover F6212-900 My dear wife thought our 2 year old steam cleaner was a vaccum cleaner and used it with no fluid, I used it yesterday, it didn,t seem to clean the carpet and no water went into the dirty water tank it stayed dry. motor sounded ok Am I in big trouble Thanks for any help you can offer P.S. I still love her Alan from Canada


Press the handle release kick-button with your foot, extend the handle all of the way back, and take a look at the gap between the base of the unit and the handle/reseviour assembly. You should see several black hoses attached to the base and running ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

I used my Hoover FloorMate, SpinScrub Hard Floor Cleaner for the first time today. My intent was to clean the grout in my kitchen/family room floor. Since the water was dirty I know it cleaned the grout but I was only so-so pleased with the results. Any hints? What about the grout solution? Do you mean I can only use the Hoover product?


The Hoover model 800 has seperate brush assembly to do grout. The 500 model (yours) has only the one hight brushes so other means must be taken to do grout. I have a 500 and all tile floors and I'm bumbed too.\015\012\015\012Kirk Thompson ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

I had a real heck of a time with the bag installation, because after the pop i zipped it up and started to use it and then the bag of the vac, not the replaceable bag fell off and i kept putting it back on but it kept falling off and when i looked inside the bag to reattach it to the vac cleaner i noticed that the dust was all inside. i haven't even used it that much as i keep it to do the upstairs bedroom only. i love that it is so lightweight and easy to use and i hope that someone can co


Mary, I have some wonderful news for you and your Oreck XL2600 Vacuum, I called 1 800 989 3535 customer service and inquired about your bag attach problem, it seems to be a docking station problem that "may" be warranteed, however if it is missing ... Oreck XL2600 Vacuum

HOOVER STEAMVAC Model# F5842-9RM 120v 12 amp Carpet Cleanerworks well. Hooked up upholstrey attachment, used it. Reassembled to standard operation, the aggitator brushes do not work. I dis assembled brush insert verything good. ran cleaner and the square hole that the bushes insert into did not rotate with cleaner on. turned off lightly tried to turn mechinism in machine no luck. Reassembled aganin, reinserted cleaning tool, then disconnected it. agitator still doesn't work. toggled switch


... Hoover Vacuums

I purchased a hoover windtunnel 2 model#u8361900 in Dec 2007.I am very disappointed because the self cleaning filter is not turning and particles keep clogging in that area. I have manually removed the particles but the filter will not turn.I also haven't been able to use the pet brush for some time.The cleaner has not been used hard about once a week since it was purchased.I am not happy that this product has stopped working effiently since purchased 6 months ago. Thank you Marcia Long Pottstow


The filter stands up right.the bottom goes in first then snap in the top.turn it by hand and you should hear it click if you have it in right ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

No spray I have a proheat cleaner. The problem is there isn't any solution when I press the trigger on the handle to use the machine to clean a whole carpet yet if I use the handheld unit it works a treat. I have tried all the remedies in the manual.


\015\012Here are 3 common things that causes this problem:\015\012\015\012• clogged spray tips \015\012• defective solenoid valve in the base \015\012• defective trigger microswitch in upper handle ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Replaced internal pump. Color coded hoses for replacement. Marker has worn off hoses. Need proper routing of hoses from clean water tank, to heater to spray nozzles. An internal schematic of hose routing is preferred.


Hi\015\012\015\012Thanks for using FixYa. Please remove the top cover of your Bissell cleaner. Now place the Auto-Mix selector knob to the water only position. Turn the cover over. You will notice an angle on the ... Vacuums

Vacuum sucks up dirt and expells it back onto the carpet as I am using it. I have replaced the bag and took the bottom off to clean - even cleaned up the area where the dirt should go to make sure it was not clogged.


Good chance the tube from the base up the handle is clogged. Try removing the bag and look at the exit, that is where most clogs on this unit occur. Look for hair, string, etc. If clog is not there, then may be in the tube or at the base swivel unit ... Oreck XL2600 Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1031 seconds