Having problems with your Bissell Vacuums ?

The steam in my handheld steam shot does not seem to be very hot therefore the surfaces, specially cloth ones do not get clean properly. What should I do?


Answers :

If it steams it is as hot as it is going to get. Water steams at 212 degrees F at sea level so the only way to increase that heat is to pressurize that steam to a higher density than sea level which is about 32lbs per sq. in. Your steamer has no method to pressurize that steam to increase that heat. Conversely, as the pressure decreases, say you live in Denver which is about 5000 ft above sea level, then that steam will only get to about 203 degrees F. (See: http://whatscookingamerica.net/boilpoint.htm) Steam Cleaning at best is a poor method of cleaning as all it does is saturate the clothing item with water, which in theory loosens dirt, but no way is provided to remove the dirt. A rug shampooer has a vacuum that sucks the dirt away from the carpet along with the suds for a better cleaning method. In my opinion a hand steamer will only remove wrinkles at best.
Repair Help & Product Troubleshooting for Bissell Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The steam in my handheld steam shot does not seem to be very hot therefore the surfaces, specially cloth ones do not get clean properly. What should I do?


If it steams it is as hot as it is going to get. Water steams at 212 degrees F at sea level so the only way to increase that heat is to pressurize that steam to a higher density than sea level which is about 32lbs per sq. in. Your steamer has no meth ... Bissell Vacuums

We are VERY disappointed in our Steam mop. After only using twice in one year and following all the instructions, went to use it yesterday, Oct. 7th and could not get any steam out? It started up and it felt like it was heated, but no steam therefore could not clean our floors?


Unfortunately they do not work well at all but if it means anything to you your not alone. Many people have complained about the same issue. To be quite honest there really is nothing better than very hot water in a bucket w ... Vacuums

I have a steam cleaner and i can not get the black arm brush to keep one side up and when you trun on the steam cleaner the brush dose not spin when you start to clean the floor but it will spin when you have it siting up right


Sounds like you could have an elevator broken (part #2000010). You will have to take the top off to replace them or to check to see if one of them is broke. There is one on each side so when the handle is in the upright, they push againsy the brush ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Hoover steam vac supreme modl f5831-900 while cleaning brush it snapped in half where can i get a new one


You can try here http://vacuumsuperstore.com/F5831.html\015\012or contact a local repair shop, they can order for you if not in stock. ... Hoover Vacuums

My shark steam mop has stop producing the steam to clean. I only get a little water to come out to wet the cleaning pad. Is it stopped up and if so how do I get the steam and water flow back


Dear Sir/Madam\012\012Good day.\012\012We're Auto-parts manufacturer from China. We are able to supply Axles & Axle tubes , Grease Nipple,Brake hose , Auto Springs, and some other fittings. If you have any requirements about auto- ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Keep getting message 'please remove and clean Roomba's brushes'. Have removed and cleaned brushes and even fitted new one's but still getting message. Also brushes sometimes rotate, sometimes not and not picking up very well at all. Help!


Must be your inbox is full, Delete old / unwanted messages. It should resolve the problem ... iRobot Roomba 500 Series Virtual Wall Lighthouse 80201 Robotic Vacuum

Bissell proheat 2X, model 8960. The shampoo tank does not seem to work, all I get is the water when cleaning. Also the first time I used my shampoer one of the belts broke. This is the 2nd cleaner I have bought. Was hoping this one would last longer. Cleaning this model is a real pain, surely there is a better why.


... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Hello, I have the same model. And though it is three years old, starting from the last month, it does not clean anything anymore. Cannot even pick up one single thing from the floor. Every dirt gets stuck in the hose. I cleaned the hose and cleaned the filters but it still does not pick anything up. Is three years its normal lifetime or do I have the change the filters, instead of cleaning them? Thanks.


I know bissell vacuums are very cheap but they should last more than 3 years. there should be two parts to the dirt cup. remove the dirt cup and above it there should be a round plastic part. unscrew it and check that filter. ... Bissell 6594 PowerForce Bagless Upright Vacuum

Last year my wife and I bought a new Dirt Devil Reaction All Surface vaccuum cleaner to replace the older Platinum Force. After using it a couple of times the new one gets clogged with dog hair easily and shuts down. I cleaned it out completely including the hepa filter but it will not handle the dog hair. The old one never had a problem and still works. We went back to using the old vaccuum cleaner because we can not find the receipt and had not registered the new one and are stuck with a new 1


Greetings jettin_us,\015\012\015\012Normally you can contact the store you purchased the unit at, and if you paid with anything other than cash, they may be able to retrieve your receipt for you. \015\012\015\012Once you get t ... Vacuums

I have a Sunbeam Model Number 4065-000 and there is white particles comming out of the holes in the bottom. I think it is because we used tap water and there is a lot of deposits in the water. I read on the box that it was ok to use tap water and not distilled water. Is ther any way to clean the inside out to get the deposits cleaned out without affecting the possibility of doing something to the cloths that I will iron after cleaning the iron?


If the deposits are recent and still fairly soft, running a tank of vinegar through the machine should remove the deposits (obviously not using on any clothes, hold it over a sink). if the deposits are more stubborn, you can use a cleaning agent like ... Sunbeam Vacuums

My grey & purple steam mop is getting very little steam at the head. is there a way to clean it without damaging the product? or is there another solution for low steam?


Mixing white vinegar with water about a cup of vinegar and a cup of water ratio and let it steam through the mop. This is also good for steam irons and other appliances such as coffee/tea makers. The acetic acid in the vinegar will dissolve the calci ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Lost Suction This is my second hoover steamvac and i am having the same problem with my new one as i did with the old one that i tossed out. I have used it about 12 times and it worked great the first 6 times... Now i'll empty a full tank of water and only half will get sucked back up. I have tried taking it apart and cleaning and also the rubber seal had some gaps so i sealed those thinking that it was leaking air from there...can anyone help? I am so close to chucking this one and buying somet


Usually when there is no suction, one cause is the lid to the recovery tank is not on all of the way in the back. Also if you have that foam filter on the underneath side of the recovery tank lid, it needs to have a 1/4 in or so gap from the top of ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Getting a Eureka central vac cloth bag back in after cleaning


I found that if you start by making sure that the tab that you pull to remove the filter is in a spot where you can reach it next time you need to remove it. Next, put the filter in over the inlet spoutand push it up to the white "stops" then gently ... Vacuums

I have a shark steam mop and it will not get hot and steam the water so I can clean the floor. The green light works on the front and that is all that works. It there an element or something inside that heats the water. It is under warranty they should have to replace it.


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Have a Shark steamer. Tried the vinegar, tried the CLR, tried putting a piece of wire and a skewer into steam hole...no luck. The unit gets hot but no steam. Will try one more round of CLR and let it sit overnight. Other than all that I mentioned...have no idea what to do next. It's a great gadget if it worked!!


\012\012\012Hi,Here\012is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it\012may not be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

We have a Bissell Proheat Steam Cleaning machine, Model# 7901-9 08053C. The water is not circulating to clean the carpet. We have delved as deep as possible to clear any blockage. What can be done to get the water circulating again?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My Shark seems to be clogged, and steam will not come out. I know that it is making steam due to the pressure, but it will not come out of the mop part. How can I clean it to get the mineral deposits out?


Normal\012 0\012 \012 \012 \012 \012 \012 \012 MicrosoftInternetExplorer4\012 \012\012\012\012\012\012 /* Style Definitions */\012 table.MsoNormalTable\012\011{mso-style-name:"Table Normal";\012\011mso-tstyle-rowband-size:0;\012\011mso-ts ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Poor cleaning I recently bought the Shark Steam Mop as I read mainly fantastic reviews. I was disappointed to find that it leaves a slight film on my dark hardwood floors when finished. I can wipe the film away with my finger and you can see foot prints if walked over. I also found that there are cloth streaks on my ceramic floors after drying as well. I followed all instructions, vacuumed beforehand, used distilled water even though my water is not considered hard, cleaned slowly, etc. I am wo


Hi,This type of problem usually is not he fault of the Shark Steam Mop.The problem is the old residue left on the floors by other cleaners.Here is a tip that I wrote that will help you out with that problem... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I have a HSCU800B upright. The bag slipped off and the contents is inside all over the cloth bag. I need to remove the outer cloth bag in order to get it clean. How can I do that?


... Hoover Vacuums

RE: DYSON DC07. Cleaning the roller I removed one end and cleaned it. Cannot get the roller back on the vaccum. If you could give me instructions on how to do this I would be very appreciated. Thank You


Try this link. http://www.sparesaver.com/help-and-suppor ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

I am getting a lot of dog hair on the filter after cleaning one room, this is something new. I cleaned as many parts as I can. It seems like the dog hair is moving from the clear canester onto the top of the filter, any thoughts??


The cone in the tank has a black gasket make sure it hasn't slid to far up ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Roomba Discovery Roomba is fully charged and cleaned with sensor wiped clean. When turned on it it sounds normal and commences to go, but it then acts like it is putting on the breaks, spins, tries to go and manages a short distance and breaks again, just not making any progress because it keeps breaking after a foot or so and turns and tries again. Sometimes is gets so stuck from moving forward at all, like it is stuck in one spot just trying to go while seemingly surrounded by barriers. Somet


I had the same back-up, turn, move forward a couple inches, backup-up, etc. problem. Try cleaning/cutting the hair, etc. out from around the brushes, as well as around the ends of the brushes. Also, try a Q-tip to clean out the four pair of sensors ... Roomba Robotic Floor Bagless Vacuum

I have a Hoover Elite Rewind vacuum. Actually,this is my second one. However, after about 4 months of use, it emits a "sour" smell when I'm using it. I empty the cannister before each use and clean out the filter monthly. My house has mainly hardwood floors, so I typically only use it on area rugs and 2 small carpeted rooms. Is there any way that I can get rid of the smell? I've tried putting a dryer sheet in the cannister, but this gets stuck in the filter mechanism. Also, carpet fresh clogs th


Does it smell like an electrical burning odor? could very possibly be the motor going bad already. ive seen it happen. but if not try freshwave odor absorbing pearls. i carry it in my store and we do have shipping. Truly the only thing you should use ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

When squeezing trigger and Depressing Clean surge Button on Upper handle of the Hooover Steam Cleaner F5914-900 there is no "snap" indicating trigger rod is in place. Everything else went in as instructed. The screws and bolts were no problem this concerns me because the main complaint I read about this model was leaking from the trigger and clean surge and the problem was not getting the rod in place. No matter how many tries or people (three) it still doesn't occur.


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=552215\015\012Generic problem for all Vacuums\015\012When squeezing trigger and Depressing\015\012P ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0896 seconds