Having problems with your Bissell Vacuums ?

Bissell vaccuum has a lack of sucking power and appears to be overheating


Answers :

Check for blockage in the hose (if it can be removed, the motor should sound less 'labored' if the path is clear), check or replace the filter bag. (For cannister types). Uprights may have a blockage in the tubing from the pickup head to the motor.
Repair Help & Product Troubleshooting for Bissell Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bissell vaccuum has a lack of sucking power and appears to be overheating


Check for blockage in the hose (if it can be removed, the motor should sound less 'labored' if the path is clear), check or replace the filter bag. (For cannister types). Uprights may have a blockage in the tubing from the pickup head to the motor. ... Bissell Vacuums

My bissell power force bagless model 6594-w vaccuum is not sucking up when vaccuuming but if i use the hose it works


Remove the bottom plate that covers the brush assembly and check the air passage that goes out where the vacuum is jointed between the vertical parts and the sweeper head. Look for any clog in that area. A bent hook on the end of a piece of coat hang ... Bissell 6594 PowerForce Bagless Upright Vacuum

I have a Bissell ProHeat 2X which releases the water/shampoo mix fine, and will suck up using the hose, but will not suck up using the main floor unit. Have checked it all out, and there do not appear to be any blockages. Help please


The vacuum on its back then look under the front where the water comes\015\012out, you will see few little round holes now the chances are these\015\012holes are blocked so get something long like a pin and poke these holes\015\012through you should ... Vacuums

I have a bissell power lifter model 16603. The hose to the siphon tube is not fitting tight into the top of the power unit. It is also not sucking water from the bottom canyou please help me


... Bissell Vacuums

Vacuum cleaner hi.this is 10 yrs old and not overly worked.bags are changed regularly and the micro filter has been changed at least three times over ten years.it goes well for about 2o minutes then loses power with not much "suck"after that.sometimes shutting down completely,because of overheating i presume,or just carries on at a much lower'"suck".have tied shaking bag inside but no luck.any suggestions out there or can you tell me the agents support office for new zealand[auckland].many thank


What brand vacuum is it? ... Vacuums

My Bissell 9200 is not sucking the water into the dirty water resevoir. 1. The gasket on the clear-view seems fine. 2. The suction power just doesn't seem powerful enough (feeling with my hand). 3. The brushes turn fine and belt is fine (not sure if that even matters for this issue). Any help appreciated. Thanks, - Matt


Disassemble all lines and check to see if all O rings are installed. If cracked missing or stretched out of shape no suction will be provided ... Bissell 9200 Upright Vacuum

I accidentally sucked up a string. The brushes stopped rotating and the suction was low. I took the frame off the brushes, and the rubber belt came out. How do I re-attach the belt/fix this problem? It is a Bissell power force turbo upright.


You'll need to replace the belt. \015\012On uprights with rubber belts, the belts need to be replaced every 3-6 months due to the fact that since the belts are rubber, they stretch, and once they stretch out they decrease the rotational speed o ... Bissell Vacuums

My brushes do not turn on my power glide pet vacuum cleaner after I accidentally sucked up the hem of a curtain. I switched off the machine then removed the hem. Now when the vaccuum cleaner is turned


... Electrolux Vacuums

Hi. My electrolus epic 6500 sr just stopped working while I was vaccuuming. Only the power light appears. I unplugged it, let it cool down, replaced the air filter and the bag. It still does not go on. Any suggestions?


It seems that the power supply unit has got the problem. Must check it up for any defects. There could be a burnt out connection. A bad switch too could be the culprit. The machine is getting the power is indicated by the power light. Hence one can d ... Electrolux Epic 6500 Vacuum

I have an old Miele canister vacuum and I do not know how to disassemble the hose to check for a clog. I think it sucked up a nerf ball the size of a ping pong ball. I changed the bag but it did isn't appear to be in the bag. The vacuum powers on but I do not have suction with the hose, and since the hose has hard plastic elbow joints I do not want to pry them apart and break it


Hi Emily: If you have the model number for your machine you may be able to find your manual on the Miele website. Check ... Miele Vacuums

The bissell power steamer will not suck back up dirty water


... Bissell 1693 PowerSteamer Upright Vacuum

My Bissell doesn't appear to be sucking up any water, it is the first time to be used. The carpet isn't saturated but when I went to dump the "dirty" water, there was no water. So apparently it is in the carpeting.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bissell bagless is sucking but the debris are not collecting in the canister. Filters have been cleaned & hose not appearing to be clogged.


Have you checked the belt. If the brush is not turning,the brush is not sweeping.\015\012Joe ... Bissell 6594 PowerForce Bagless Upright Vacuum

Extreamly Loud this vaccuum has great sucking power I have used it about 4 times it is very loud it sounds like a screeming banshee. It actualy hurts your ears to use it. the filters are new the roller is clean and rotates freely what is the problem with it?


Most likely you have a bad motor bearing. It's a pretty common problem with vacuums of this type... a good way to check is to open the bottom where you replace the belt, and look at the motor pulley. If it's blued, your bearing is most likely generat ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum

While cleaning, the vacuum sucked up a nail and I suspect it may have punnctured the hose from the vacuum base to the uppper cannister. The reason is that it appears to have lost its suction power and nothing gets into the fliter cnnister area any more. How do I replace this part ?z?


You will have to basically split the vaccume in half to gain access pulling the plastic covers off.usually philips head screw/ ... Bissell 6591 Power Trak Revolution Bagless Upright Vacuum

My bissell cleanview is blowing not sucking in the base. the hose works fine and the bruch appears to be rotating fine.


Try reversing your hoses.\015\012Hope this helped.Let me know by rating meFor more help go to live chat.lenwest ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

The power nozzle on my c141b model aerus electrolux canister vaccum no longer turns on. It was working when a large stringy object was sucked in. When hitting the red reset button, nothing happens. Is it likely that it is the fuse that needs to be replaced? All wires appear intact (I replaced the elbow assembly a few months ago.), and the sweeper moves freely.


It's not a fuse.\015\012Turn the power nozzle on it's top. Try to rotate the brush. If it won't spin, there's till something holding it. Remove all strings, threads, and whatnot from the roller. Try to rotate it again. If it still won't sp ... Vacuums

I have a bissell power force vacuum and I just pulled the bag out to change it and when I put it back in it began blowing air out the filter on the side and is no longer sucking


Hello,\015\012Try checking the attachment hose for clogs. It should come completely off of the vacuum with just a few screws. Also, check the little hole underneath the brushroll where the dirt goes in. Hope this helps...\015\012Marci ... Vacuums

My bissell power force helix won't suck in all the dirt and stuff. It just blows it all out instead.


... Vacuums

Water suction My Bissell Proheat Clearview is not sucking up water into the tank, motor appears to be fine


Here's what I did. On the top of the water bucket there is a red oval screen, remove and clean the screen and replace. Also, next to the screen is an oval opening which meets up with a black oval gasket on main unit. Inspect the gasket and replace if ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

Bissell PowerForce Turbo: The motor spindle becomes very hot while spinning, causing the new belt to burn and break. Is this because the motor is overheating?


Something is preventing the brush roller from turning even though it seeems to be OK when not in contact with the floor. The motor shaft is spinning on one spot of the belt, causing the heating, the smell, and eventual belt failure. I have had brush ... Bissell 6594 PowerForce Bagless Upright Vacuum

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920


The brushes will only work if the handle is released and the ProHeat vacuum is running . There is a micro switch inside the lower handle that switches on the DC carpet brush motor. The DC power for the motor comes from a Bridge Rectifier on the PC ... Bissell Vacuums

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920


You need to change the belt(s). You can find the belts for this model here. http://www.vacbelts.com/bissell-proheat-belt-combo-pack.htm ... Bissell 8910 ProHeat Clear View Upright Vacuum

Bissel proheater I have a Bissel proheater 7901. When you power on the spray works fine for 2-3 seconds then will not spray. Power off for 30 seconds and then repeats the same thing again when powered on. I'm thinking the pump is bad. Any other ideas?


Will water squirt out of the hose? If it does, then you could have a clogged heater, which is in the handle. Check the bottom of the tank, is the round seal on the valve that is on the tank bottom? If not, it has to be there. Another thing is the ... Vacuums

My bissell power steamerr 1697-w won't dispense water, pump belt o.k. what else couuld it be


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0773 seconds