Having problems with your Bissell Vacuums ?

Bissell ProHeat Clearview Steam Cleaner - need steps to clean the clear input area. I have removed the four screws and need to know how to finish the removal of the clear plastic input area.

Answers :

For the clear outer nozzle, there are 2 screws holding it in place. Remove those, then from the bottom lift it up. Sometimes the seal holds it really tight and you may have to carefully pry on the sides until it loosens up. Then when you put it back on, at the top are 2 tabs, make sure they snap into place then lower the nozzle and put the 2 screws back in.
Repair Help & Product Troubleshooting for Bissell Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bissell ProHeat Clearview Steam Cleaner - need steps to clean the clear input area. I have removed the four screws and need to know how to finish the removal of the clear plastic input area.

For the clear outer nozzle, there are 2 screws holding it in place. Remove those, then from the bottom lift it up. Sometimes the seal holds it really tight and you may have to carefully pry on the sides until it loosens up. Then when you put it ba ... Bissell Vacuums

I want to open a Hoover S3825 Elite Cyclonic Vacuum to see if I can repair or replace the cord reel assembly. Currently the reel slowly draws the cord back into the canister once it is pulled out. I found the mounting screws under the rear wheels once I removed the hub but I do not know how to remove the rear wheels, everything is plastic. The front screws are under the front caster wheels and I think I need to take a screwdriver and pry off the little cylinder wheel to get to them by rotating

... Vacuums

I have a Kenmore Wispertone 300 cannister and I am trying to access the motor. There are four screws shown in the parts diagram. I need to remove the plastic on/off pedal to acess two screws. How do I release the pedal?

I just encountered the same problem on a Whispertone 116 last evening. If it is the construction same as mine, there are four flexible plastic retainers molded into the top cover in the gap between the pedal and the motor cover. These are on the hing ... Kenmore 23313 Whispertone Bagged Canister Vacuum

I have a Honeywell HF810 fan. I am trying to clean it. I removed the phillips head screws, but their are two odd screws that require a special tool to remove them . I also have to go through the plastic shaft, so I need a special type of screwdriver and a special type of head. Thanks for the challenge!!

... Honeywell Vacuums

Hoover Alpina 2 1300 cleaner. I need to split the upper and lower casings to check that the switch is working. I have removed the screwa in the area around the bag, but now need to remove the switch and cable rewind covers, as I assume there are more securing screws under them. Can you advise how to do it please?

Move covers (forcibly !) away from the centreline of cleaner then move to rear until released. The covers are held by slide catches on inner edges. ... Vacuums

How do i remove the front of the Proheat Clearview to clean it out? I removed the two obvious screws at the front sides of the clear plastic part but see anything to remove to take it off.

... Bissell 1699N ProHeat Clear View Force Upright Vacuum

On the bottom of the Fantom Fury where it states:"The United States and Canada utility patent....". Now go to the far right end of this statement (the end opposite the spring, well I have a crack in the plastic which, when toggled, moves the entire plastic underside of the vacuum to move. In other words, I think I need an entire bottom plastic plate. The cracked area also makes the foot lever (which lowers or locks the vacuum handle) not work as the crack makes it impossible to work. I know

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=545424\015\012Generic problem for all Vacuums\015\012On the bottom of the\015\012Posted by c ... Vacuums

My son spilled mica all over my carpet. To clean it I used my bissel vaccuum. Now I have orange mica in the removable filter area as well as up inside the part that spins. I need to clean it out, but don't know how to remove it from the vaccuum

Load it into the trunk of your car, take it to a gas station and use the tire inflater hose to blow all the **** out of it.\015\012May have to get a tire stem in order to use it as a blower. ... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

How can I remove the pet hair that is trapped in the initial vacuum assembly? I don't see screws for removing the clear plastic panel

Generic comment.\015\012\015\012If the parts aren't glued in, they must be snapped in or fastened with screws. You say there are no screws - try unsnapping.\015\012\015\012I think id try a coat hanger first with the help of a ... Hoover F5870-900 SteamVac Vacuum

Old Sanyo 1500 watt "Power Control" vacuum cleaner. I need to remove the plastic covers that are attached to the on/off switch and the power cord recoil. This will allow me to remove the retaining screws for the upper motor cowling. The motor and wiring is clogged with wood dust and I want to blow the dust out using compressed air.

... Sanyo Vacuums

I have a Panasonic MCV7515 UPRIGHT VACUUM and need to remove the cowling that covers the brushes to clean the hair out of the bearings, but it isn't clear how that can be done without a crowbar or sledgehammer. Removing all the visible screws makes the hindmost part loose, but not the front half. Also, is there an easy way to replace the belt?

... Panasonic MC-V7515 Bagged Upright Vacuum

I have a EuroPro Infinity NV29 and I have a clog in the base. I have removed the screws and the plastic piece where it says access port to remove clogs but don't know how to get the hose lose to empty it.

... Vacuums

Vacum I need to check the brushes in the motor smells have removed four screws but the cover is not coming off. I dont want to damage this by forcing it but cannot find any other screws Thanks fairweather

Hi there!\015\012\015\012It would certainly help if you said which model it was.\015\012\015\012I can only give generic help now, and do the best I can for you.\015\012\015\012Most plastic products rely heavily on ... Vacuums

How to disassemble electrolux ZAM 6280?i had already removed screws and don't know to disassemble it. i need to check fuse or if it needs resetting.i'm using it and it suddenly stopped completely.no power at all.

Hi There.. I had the exact same problem with my ZAM6280 model. The PCB part (location C8) had blown. Do you know the details for that part, so I can replace it? Otherwise, you didn't happen to come across any schematics for the PCB Module?? ... Vacuums

I have a bosch ergomaxx 2000w which I need to strip down and clean. Ive found 6 torx screws bit still can't remove the coloured plastic cover. How do I remove it?

Got the same !Remove both back wheels (just pull gently with a screwdriver), then with a big screwdriver pull the cover while pulling plastic locks in the side holes (under the wheels) whith a small screwdriver. ... Bosch Vacuums

I am working on repairing a model S3101W shark steam mop. I took out two screws and took off the swivel head and a short clear plastic tube fell out. I do not know where it goes. No spring fell out with it. Where does it fit? What holds it on. Thank YOu

The same problem Im having, and Im not a handy person at all..Im about to junk it..I have no idea what Im doing :) ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Hoover self propelled bagged windtunnel upright model #U6435-900...how do you remove the green plastic shell cover to get to the part that secures the v belt...we need to secure the bolt and cannot get the area. Brushes and transmission wheel not rotating? thanks

Greetings from GoVacuum,\015\012\015\012Here's a great video repair tutorial that we've put together to try and help you with the repair on your Hoover WindTunnel. I hope that this helps you with your repair. If you found this solution ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Thank you for the detailed explanation regarding the kirby vacuum functions, but we would like more information about the exact shampooing instructions. in explanation we would like to know exactly what solution and in what quantity to apply first to the fabric... how long we need to let it soak in.... and how to remove the stains using only our kirby vacuum witjh shampoo attatchment from start to finish...

... Kirby Ultimate G Bagged Upright Vacuum

I have a Kenmore Progressive Canister Model # 29612992. I was replacing the sweeper bag, when I opened the lip, the plastic arms was pull out of joint and will not close. I removed the 2 screws under the lid to put back it in place but there I can't remove the plastic molding because there are still screws holding somewhere. Are there tabs instead of screws still hold the molding?

... Kenmore 25512/ 25513 Progressive Canister Vacuum

The retracktable power cord on my Panasonic MC-E7103K is jammed inside the machine. Does anyone know how I remove the cover after removing the two visible screws? Brian

... Panasonic Vacuums

How to dismantle a Miele S 5980 vacuum cleaner. The RESET switch has fallen in and I can't remove the plastic panel to replace it. Neither can I remove the cleaner body to get in from beneath. I have removed 2 screws from the front of the barrel (nozzle end), one screw centre front, two screws towards rear, but there seems to be something else holding the housing together. [email protected]

... Miele Vacuums

I have a Kirby G5 and need to replace the gear drive shaft, as the lever inside fell off and the shaft came out. (Common problem by the sound of it.) How do i remove the actual gearbox itself. I have removed the 3 screws on the bottom, but it's not coming out. What's stopping it from coming out? Do i need to remove the gearbox drive belt first? If so, how do i get to it? Thanks in advance.

HELLO, JUST USE THIS GUIDE! :0)http://reviews.ebay.com/REPLACING-OR-REPAIRING-KIRBY-VACUUM-NEUTRAL-DRIVE-PEDAL?ugi ... Kirby G5 Bagged Upright Vacuum

Kenmore Model 116 Cannister Vacuum.Trying to get into motor area. Think belt is worn out. I have removed the front two screws under the hinged cover, but can not remove cover over motor.. Still attached at rear. No evidence of any more screws to remove.

Under the cordwinder actuator button, are your other two screws. To remove this cover, take a flat tipped screwdriver and , very carefully, find the "tabs" (there are two) both on the front section under the button. Then, Carefully, press them in a ... Vacuums

I have an Elextrolux Discovery Advantage(upright) . I need to replace the lower hose. Unfortunately the hose comes out of the roller/feeder area fine but I believe it is held in with a screw in the canaster area. My question is this: How can i open the Canaster area - ther is no isable screws

It's simply screwed into the tank. Simply unscrew in a clock-wise direction to remove. To install the new hose, screw in in a counter-clockwise direction. This is opposite the direction normally used for regular screws. \015\012You don't ne ... Electrolux Vacuums

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless

Get over it and buy a new one!!! ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0874 seconds