Having problems with your Bissell Vacuums ?
Bissell Spotbot Pet Model # 33N8A. "Hose" button is only one that works, and only intermittently.
\015 When I plug it in, the power light comes on, but none of the buttons ("Surface Stain", Set-in Stain", "Hose", "Pause/Resume", and/or "Stop"), work when pushed. If I unplug it for 10 seconds, and plug it back in, the "Hose" light starts blinking green, but if I push it, nothing happens. If I leave it alone, it stops blinking, and we're back to square one. If, however, I un-dock the manual hose end while the "Hose" light is blinking, it immediately starts up, and the "Suction" and "Spray" indicator lights come on, and the manual hose works as it is supposed to. But none of the other buttons work, even in this mode (most notably, "Stop" and "Pause/Resume"). I've cleaned the removable rubber gasket around the dirty water collector intake , and cleaned around the injector on the solution reservoir, all to no avail. Does anybody have any solution(s) to this problem? Thanks. Paul\015
Repair Help & Product Troubleshooting for Bissell Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Bissell Spotbot Pet Model # 33N8A. "Hose" button is only one that works, and only intermittently.
... Bissell Vacuums
My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc
... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
I have a remote Hunter Ceiling Fan w/ remote 1-2-3 fan speed buttons and one on/off/dimmer light button. Model Number CP-9110R. It only has one pull string and it is for the light. I would like convert the light to work off of a simple wall on/off switch and the fan to be controlled by a 3-speed pull string. Can I by-pass all the sensors and make it work?
I see noone has answered so I will.Yes,it could be done,but if there is not a conversion kit for your fan,it would not be wise to do it.For starters,all of the things required would probably cost at least $15.Also,there is at least one tool you would ... Vacuums
My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920
You need to change the belt(s). You can find the belts for this model here. http://www.vacbelts.com/bissell-proheat-belt-combo-pack.htm ... Bissell 8910 ProHeat Clear View Upright Vacuum
The brushes will only work if the handle is released and the ProHeat vacuum is running . There is a micro switch inside the lower handle that switches on the DC carpet brush motor. The DC power for the motor comes from a Bridge Rectifier on the PC ... Bissell Vacuums
Bissell proheat 2X, model 8960. The shampoo tank does not seem to work, all I get is the water when cleaning. Also the first time I used my shampoer one of the belts broke. This is the 2nd cleaner I have bought. Was hoping this one would last longer. Cleaning this model is a real pain, surely there is a better why.
... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
Dear Sir: I just purchased a Bissell Rug Shampooer at a garage sale. The only thing I find for a model is on the back and it says Model 1695 there. Nothing on front. It is Navy blue and has a grey tank on it with a smaller one inserted at bottom of the large tank. It has two switches on the back of it and the trigger switch at the handle. The cleaner works, BUT, it does not extract any water back into the tank that is to pick up the dirty water. Could you suggest what I may look at t
... Bissell Vacuums
Panasonic NN-SD776S microwave Start button stopped working. I know, the first thought is a bad door switch because "everyone knows a microwave should not turn on if the door is open." I am experienced with electronics, but even the timer won't start at all. Funny thing is, I had this exact model do this exact thing just over 2 years ago - troubleshot all the hardware until I was lost, finally bought a new one from Costco (June 4/08). And now 2 years later this one craps out - a 2 year timer
Hello Aaron,Since your microwave is controlled by logic, and the start button / timer portion is not working, I would start troubleshooting the power supply.Get a look at the integrated circuits that are on the circuit board, ... Vacuums
I have a littermaid elite automatic litter disposal system. It stopped cycling and both lights are flashing. Nothing is stuck, it just made several passes at some point overnight without successfully getting to the receptacle due to heavy litter. The box was clear and moving before we went to bed. This morning the lights were flashing. I unplugged, emptied, etc and it will not work. what now? It does not have the reset button at the receptacle button that the old models did. Is there one?
Bissell spotbot manual button doesn t work light just flashes
... Bissell SpotBot Hands-Free Compact Deep Cleaner - Silver
Bissell SpotBot model 7887 still seems to clean ok, but there is no wastewater appearing in its tank on normal "Fresh Stain" and "Set-in Stain" settings. Seems to work on the "Manual" brush setting though.
... Bissell SpotBot Robotic Wet/Dry Vacuum
We are trying to replace the belt on the bissell 89q9 model. We purchased belt 8 and got in onto the brush however the brush doesn't spin anymore. Even trying to turn it by hand doesn't work. One end of the brush has a round end to slide in (clear end piece); however the other has a rectangular end to slide in (black end) so we don't even know how it ever turned. Any suggestions?
Remove the beater brush assy & remove the\015\012shaft & brgs that go through it 7 clean out the \015\012hair,fuss ect,so it will turn\015\012\015\012You need to take your vacuum apart once a year or more\015\012to clean ... Vacuums
I purchased a brand new Eureka Pet vacuum, sorry don't know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
If the motor is running, there should be suction. Possible problems depend on whether it's a canister or upright and are:\015\012A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out ... Eureka Vacuums
I have a Bissell pet hair eraser model #3920. It's been working great until last night. I went to use it and the brush won't spin. It also smells like it's burning. I checked the belt and it looks fine, and the brush spins by hand easily. It's not clogged anywhere that I can see. Anyone have any other ideas? This vacuum is only 8 months old.
- Remove the access panel, which is on the bottom of the machine. There are 4 tabs to lift on the access panel to remove. Start with tab 1 then 2-4 tabs.- Check the brush, and belt for any damage. Clean off any debris on the brush. ... Bissell 3920 Bagless Upright Vacuum
I have an Amana above range Radarange, Model #AMV4204AAB, Serial # 10168958GE. Tonight after running for a 7 minute period and finishing, it would not again start. There is power to it, but various buttons no longer work. The following buttons won't work: Kitchen timer, Light Timer, #5 button, Popcorn, Poultry, Auto Defrost, and the Start button. Any help?
Hi,\015\012\015\012Push\015\012the power cord all the way into the outlet in case it became loose and\015\012is causing the problem. If the microwave still isn't working, check for\015\012a blown circuit fuse, and repair it ... Vacuums
I have a Howard Miller Westminster Chime Mantle Clock. It has always worked fine. It stopped working and my husband took the battery out to change it and when the new battery is in it will not work. It is Model 613-=103 movt 354201J dial 272142J. The part you put the battery in almost looks too big for one double A but I can't see how two would fit. I am afraid the battery is just not in right. Can you help me with how many batteries go in this clock or if it is one what the problem could be.
I have a new (couple of months) Cuisinart Espresso Maker EM-100C. One has to turn on the power button on the front in order for the unit to heat the water. The button will only work if the two manual knobs are in a certain position. Very occasionally, it took a few tries to get the button to turn on. Now it usually does not work but will once in a while. Any ideas what we could do to repair this problem?
The beater bar motor doenst work when i push the bar button the bar button doesnt light up like power button how can i test bar motor or bar switch or what is the common problem wiyh this model I have 2 that dont work the same way
If it do not work ...and you already are on the second one that behaved in the same way it may be a problem with the power in your place and the cause it may be the main fuse...Im not sure where is located in this model but it has to be near the powe ... Vacuums
My electrolux Epic 6500 power nozzle Model N109J will not work. It had an intermittent short which I thought I fixed (some of the insulation on the wires were pinched). I fixed the wires and it worked intermittently for an hour then shut down completely. Could the reset switch have a short? When I press the switch nothing happens.
The switch is definitely a possibility, but other problems can also cause this.\015\012Bad switch, needs replaced.\015\012Broken wiring in power nozzle, wands, hose, or canister.\015\012Bad PN motor.\015\012\015\012I str ... Electrolux Epic 6500 Vacuum
I have an older model Bissell rug shampoo machine, model # 1631. I have several bottles of Bissell 5 One carpet formula to use in this machine, however I have lost the measuring bottle that tells me the amount of soap solution to use per 64 oz. bottle of water. I sure would appreciate if you could help me.
I have a older mod. Bissell carpet machine plus mod. 1630-5 and need a floor nozzle part num.013-6194 and grip tube w/button part num.014-4181 and trigger part num.010-9406 and tube ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
I have White Speedylock Serger, model 1500 that will not work when I press the foot pedal. I thought it might be the pedal, so I ordered one on-line, but the new one does not make it work either. I have checked the needle and it is fine, not loose or broken. The presser foot is fine also.
If either of the foot pedals are for sale I am interested. [email protected] ... Vacuums
The model is Miele S538, but I did not see it on the list. The suction power button( ) increasing the power does not work. The suction power button (-) decreasing the power does work.
... Miele Leo S5381 Canister HEPA Vacuum Cleaner Bagged Vacuum
No Suction My two year old Kenmore Progressive stopped working in January. The guy at the Sears service center convinced me that buying a new one would be cheaper than getting it fixed. So I bought the exact same model and now this one has given out in the exact same way! I'm so confused. When I press on, it lights up and makes the whirring noise. Everything seems to be working but there is no suction anywhere. Not in the main part or the hose and there's no "cyclone effect" in the chamber. All
Try looking within the vacuum to see where the suction is getting stuck at. You may have to do some disasselbmeing but this is a manufacturers problem. You should also try to speak to the manager at the support and make a big dispute until you get yo ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
Have Model 350A with Chime Model MC3. Door bell does not work. Light is on at the button outside so there is power there but when you push the button - no chime at the intercom system
... M&S Systems Vacuums
Hello, I just bought a Bissell Powergroom (model 92L3-W) vacuum and a Bissell Proheat Pet (model 8910-3) deep cleaner and I love them both. My problem is, when we unpacked them we somehow lost the manuals; I think I had too many helpers that night – they may have gone out to the trash with the boxes. I need replacement manuals if you would be so kind as to help me out. Could you email me a manual for each of these two machines, or tell me exactly where to find them online? I’ve been looking, but
Follow the link below and enter the model numbers to access the User's Guides.\015\012http://www.bissell.com/customer-support/ ... Bissell 8910 ProHeat Clear View Upright Vacuum