Having problems with your Bissell Vacuums ?

Replacing a pump belt - Bissell Vacuums


Answers :

Repair Help & Product Troubleshooting for Bissell Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Replacing a pump belt - Bissell Vacuums


... Bissell Vacuums

I replaced my Bissell vacuum cleaner belt with a Bissell belt. I ordered it from them so I know it's the right one. I replaced it and the roller won't spin and the belt smells like it burning.


Beckiande485: You will need to unplug the vacuum from the wall, lay it down so you can see the bottom of the vacuum head and remove the bottom plate (foot plate) Probably philllips head screws. pull up on the roller (called the beater bar). ... Bissell Vacuums

Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there's two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it's a ribbed belt? that is the water pump belt?


Just taken ours apart with the same problem... found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places - the bottom of th ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Bissell 1697w I just got the bissell 1697 steamer and I had to replace the pump belt. I can not figure out how to change the belt.


First take off the belt cover on the side,\015\012then turn it over, on the belt end of the brush roll, there is a red piece to hold in the brush roll, take out that screw and pull it off, the you can remove the end cap and cogged belt, Put th ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

How to replace the belt on my bissell model 3512-9 vacuum


Tehre are tabs on the bottom. Push them in the direction of the arrow (one at a time) and lift with some force on the cage thingy that partially covers the sweeper. Do the same for the other side. It doesn't matter which side you do first. ... Vacuums

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a


... Bissell ProHeat Deep Cleaner Upright Vacuum

How do I replace a pump belt for my Bissell 8910


This link is a video of belt change for the bissell proheat. ... Bissell 8910 ProHeat Clear View Upright Vacuum

Replacing the Brush and Pump belt on Bissel Steam Cleaner 1901


... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn


Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

Replacement parts... I've got a 3594 Bissell and the belt has come completely off. In the process of breaking, it bent the metal guide inside the motor housing and melted the plastic that holds the guide and keeps the belt inline with the roller. I've got it running again by using a screw I filed all the threads off of, but it only works for 10 minutes at a time before breaking another belt. This process is getting expensive, as it usually takes 30 minutes to completely vacuum the house. Is ther


Most likely it is the top cover that needs to be replaced, part #2031238 and is around $30. It would have that guide on it. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.


You need a new belt. ... Vacuums

Instructions to replace pump belt on model 37E3 bex bissell


... Bissell Vacuums

I have a broken pump belt on my bissell powersteamer proheat. The belt was just laying in there. I have a new one but no where in the manual does it tell you how to replace it and where! Help


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1698-1 PowerSteamer ProHeat Plus Upright Vacuum

Bissell powerforce vacuum brisals will not spin and i replaced the belt and it is still not wanting to spin and I think it will pop the new belt. what is wrong with it?


... Bissell 6594 PowerForce Bagless Upright Vacuum

How to replace the belt on a bissel 3920 - Bissell 3920 Cyclonic Pet Hair Eraser Vacuum


... Bissell 3920 Cyclonic Pet Hair Eraser Vacuum

I have a Bissell Model 8905 Carpet Cleaner. I was going to replace the belts because the pump belt broke, but when I turned the machine over, a small piece fell out. It looks like a tensioner arm because it has a small round part at each end on opposite sides of an arm that has an offset or "dogleg" in it. I am looking for an exploded parts diagram to determine what the part is and where it came from.


... Bissell 8910 ProHeat Clear View Upright Vacuum

How to replace brush belt on bissel 1697-w - Bissell Vacuums


... Bissell Vacuums

We have the Bissell Lift off Revolution vacuum. The brush roll and belt are broken. The brush roll has seized up and no longer spins which caused the belt to burn out. How much is a replacement part cost? Debie [email protected]


You can get the belts for that model here: http://vacbelts.xps.convina.com/bissell-style-8-belt.htmThey are only 4.99 for a 2 pack. Plus they ... Vacuums

How to replace belt on bissell 7901-1 - Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum


Go to link below. On page 18 and 19 tells you how to replace the belt.\015\012\015\012http://www.bissell.com/images/UserGuides/7920.pdf ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Replace belt on Bissell 7901 Proheat - Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum


On the underside of the unit, you will see a red cover about 1 inch square held on by a phillips screw on one end of the brush roller unit...remove it & you will see the toothed rubber agitator brush belt. ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My old bissell 3510 upright vacuum seems to have no suction into the bag...I replaced a broken belt several days ago, and now the vacuum picks up debris, but seems to just collect it behind a wheel..The bag does not "puff out" like it used to...How can I fix this??


... Bissell 3510 PowerPartner Upright Vacuum

Bissell 6595 problems with roller brush. I've had this happen with two of the same model. Each one didn't last more than seven months! First, it became loud when vacuuming, then there was a burning smell. When you try to replace the belt, you see that won't do any good because the fitted end of the brush is melted. The housing part the roller brush fits into is melted too. There's no place for the roller brush to fit into. I tried to upload pics, because I don't see how replacing the roller brus


... Bissell 6595 Lift Off Bagless Upright Vacuum

I have a Bissell Lift-off Revolution Turbo vacuum and the brush doesn't spin on its own anymore. Does this mean the motor is busted because there's no noise when you press the brush button. We've just replaced the belt, hepa filter and a new brush. But its still the same. What's wrong with my vacuum?


Its probably the motor. remove the covers with a #2 phillips head screwdriver and cut the wires to the motor ( unplugged ). purchase some crimps at radio shack to resplice the wires together in the same fashion. ... Bissell Vacuums

How to change pump belt on bissell pro heat - Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum


First take off the cover on the left side oif the top cover, then turn it over, remove the screw holding the red lock and pull the cap and brush roll out, remove the cap, remove the cogged belt, then you can put the new pump belt thru that slot, put ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0848 seconds