Having problems with your Bissell Vacuums ?
How can i remove the dust from vacum hose?
\015 How can i clean the dust from the vacum hose in the bottom side?\015
If you can take it apart and remove the hose then I would flush it with a hose with a nozzle. I would also spray the inside of the hose with an all purpose spray.
Repair Help & Product Troubleshooting for Bissell Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
How can i remove the dust from vacum hose?
If you can take it apart and remove the hose then I would flush it with a hose with a nozzle. I would also spray the inside of the hose with an all purpose spray. ... Bissell Vacuums
I have a Miele Vacuum cleaner MedicAir 5000 Plus. Recently the Dust Bag Indicator bar is full during normal cleaning and consequently the suction power is much less. I replaced the dust bag, engine pre-filter and Hepa filter but no change. When i remove the hose, the Indicator is normal, but when i attach the hose, wand, head, the indicator is full. I checked the hose, wand, head but can't see any blockage and when i blow with my mouth it seems fine. Can anybody help? thanks!
... Miele Vacuums
Recently purchase SC-N500 vacuum cleaner. Worked well only the first 2 times I used it to clean up plaster dust from floor after sanding. Since then it has not worked at all well wiht very poor suction. Fluff gets stuck in the hose and has to be manually removed. Suction power is very poor. I have washed the filter to remove the dust with no difference. Who do I contact in Brisbane to service or assess the problem further.
... Sanyo Vacuums
I bout this vacume in mid December 07 and about February-March it started not picking up the dust on the floor. So in early April I bout a new filter and it still wasn't picking up the way it had in the beginning. I've taken it a part several times and cleaned it out with it being plugged at the bottom hose with dust bunnies. Well I just took it back to Walmart where I purchased it and I failed to keep the reciet they could not do any thing about the sweeper. I went back to the sweepers and re
Pull the hose out of the holder, is there suction there. If not, then there is a clog in the hose. If there is suction, then check the dirt outlet by the brush roll. Also if the belt is slipping, it may appear to not have as much suction, belts wi ... Dirt Devil Vacuums
My dyson animal vacum hose no longer wants to **** up anything i have removed the botttom part that u can unscrew and removed somethings that were stuck in there since then it no longer picks up anything any suggestions
Check all connections and motor ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
I was vacuming with the hose only with my kirby generation 3 vacum and it suddenly made a different sound and smelled strong of burning. I immediately shut it off and unplugged it. It IS about 30 yrs old. Do you think it is worth taking in to pay someone to look at it or it just bit the dust?
It might be the belt and if it is it will be a sipmle fix. If it isn't I think It's time to bite the dust and buy new. You won't believe what you old vacuum was not sucking up and for what it would cost to repair vs buying new it would be about the s ... Vacuums
No Suction I have a dc18 dyson and it had lost suction from the main hoover and the hose part. If you remove the dust collection part there is suction from the hole behind that part. I have cleaned all part to this hoover but the problem is still there. Any help would be apprieciated. Thanks
Filter removal step 1Turn power off and unplug the machine.\015\012\015\012To remove the washable filter: Rem ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum
My vacuum's cyclonic action is not spinning and creating very little vacuum pressure through hose or floor brush area. I already checked, brushes are spinning, there is no apparent blockage in the canister, I took it completely apart and removed excess dust from the filter. Still no good vacuum. Any suggestions?
The following filter in your in your dump cup needs to be replaced. \015\012F24 Dirt Devil "I" Bagless Upright Vacuum Replacement Filter Style F24 ... Dirt Devil M130005 Bagless Upright Cyclonic Vacuum
Miele Cat & Dog vacuum gets VERY hot and is VERY loud. Hose has no restrictions and I have changed the dust compartment (motor) filter and the exhaust filter. It still gets hot when I run it with the top open and all filters removed, so I'm guessing the problem is with the motor. Should I be going into the motor compartment? If so, what am I looking for?
Hi\015\012\015\012The fact that it gets very hot could be due to a number of issues.,but the fact that it started making a very loud noise at the same time suggests that there might be more problems maybe brushes etc.\015\012\ ... Miele S514 Solaris Bagged Canister Vacuum
I have a Model 116.35922500 Kenmore upright vacuum cleaner. It makes a loud air noise when using the vacuum. I have disconnected and removed the hose to see if anything is lodged in the hose and it appears clear. It makes the noise when the hose is connected. When I remove it, the noise stops. When I place my hand over the hose, the nose re appears. I sounds as though the noise is coming from the fan or internal parts of the machine. So, when there is a load or pull on the machine, it mak
... Kenmore Progressive 35922 Bagged Upright Vacuum
Model UH60010, Series X12.0, Mfg code K09A. While attempting to use the hose and the extensions to clean shelves, my wife reported no suction. I removed the brush roller and the plastic piece just below where the hose opening is located and saw a "flapper" door that was closed and had some debris sort of jamming it. I removed the debris, but the door requires extreme pressure to open to permit the dirt, etc to moved up thru the opening , through the hose, etc. I thught maybe that somehow tg
Hello,Check to make sure\015\012the dirt canister is empty. If dirt canister is full, then you will \015\012experience\015\012reduced suction. Empty dirt receptacle.\015\012 Could\015\012 be a clogged hose - ... Vacuums
We have a beam Serenity plus home vacuum system and there is no longer sucks. I removed the dirt from the bottom plastic container, but I also notice a sack or bag connected to the unit when I removed the bottom container and inside that sack there appears to be lots of dust. How do I access that and remove that dust without damaging the unit. I don't know how to do that
Hello. Let's begin by getting that dust and dirt out of your permanent filter. To do this, get a big clear plastic bag and pull it up aroung your canister, with the dirt receptacle removed. Then Grasp the sewn in weight inside of the filter and sh ... Beam Industries 2900 Serenity Plus Central System Vacuum
Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i
At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum
I was given a model 6591, plugged it in and it worked but didnt "****" and didnt sound right. I turned it off and removed the hose from the back found a badly plugged hose. Removed the hair plug cleaned filters and when I tried to turn it on again. Now the motor will not turn on or even make a noise. I hear there is a fuse that can be blown? How can I find the fuse if there is one? Thank You Ron
The User Guide for the bissell Clearview Power Trak\012\012http://canada.bissell.com/images/UserGuides/3590C.pdf\012 ... Bissell 6591 Power Trak Revolution Bagless Upright Vacuum
The removable filter at the front is cleaned regularly, and is not clogged. However, the machine appears to be suffering from being clogged by dust, as it has started to make a high pitched noise, and I fear it may burn out. I can see some dust inside the front panel but cannot see how to remove the front to clean it out. (NB. I have located two screws - one on either side - but cannot see how to proceed further.) Please help! Thank you.
\015\012\015\012Hi,Here\015\012is a tip that I wrote about my Bissel but I bet you have the same\015\012problem and the hose is clogged...Bissell Bagless Upright\015\012 ... Vacuums
When I try to disconnect the hose in order to use the hand held hose with an attachment, the dust from the bottom flies into the air. How does this opening get blocked off to ensure the dust enters through the attachment and not the bottom?
It is a matter of Physics. It seems like you have it running when you change the hose. ?? That's a no-no.Basically you will have o take it apart until you know how it works or wont work ... Bissell Vacuums
When you remove the hose to use the utensils, the dirt is flying out of the hose at the bottom where the utensil is removed from
Hi Karen. I understand how frustrating this can be. Dust blowing from the bottom hose is normal because the brush is still rotating. If there's excessive dirt flying out, then you may have a clog in the bottom hose. \015\012Here's a quick link to ... Bissell 6591 Power Trak Revolution Bagless Upright Vacuum
Old Sanyo 1500 watt "Power Control" vacuum cleaner. I need to remove the plastic covers that are attached to the on/off switch and the power cord recoil. This will allow me to remove the retaining screws for the upper motor cowling. The motor and wiring is clogged with wood dust and I want to blow the dust out using compressed air.
... Sanyo Vacuums
I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom
Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Can you remove the plastic hose that leads to the handle as mine has split. I thought i could remove it by pushing in the two black bits of plastic then shorten the hose. so far it wont budge. Is it meant to as Dyson sell the whole thing in one? cheers john
Yeah sorry it is sold as a complete unit and its a real pain to strip down so it better and faster to just buy the whole thing from dysons website ... Dyson DC07 Bagless Upright Cyclonic Vacuum
My electrolux oxygen canister cuts on and off. I have to open and close the vacuum, or take the base of the hose off and then re-insert. I have to do all these things before it will start up again. I sometimes shake the hose around, then it will come back on. If I try to dust with the dust brush (like a lamp shade or shelf) and the suction pulls against the object, the vacuum goes off for awhile. Sometimes I'll have to reset the vacuum by unplugging the electric cord. I never get to finis
Maybe you should have taken it back to that shop, it appartently isn't fixed. I would have replace that board, don't believe in modifing, you usually end up with other problems, like you have. One thing to check is maybe you have a partial clog in ... Vacuums
My vacuum hose has split very close to the handle- how do I remove the handle, cut the hose at the split & reattach it to the handle unit - Centralux central vacuum system. Where can I find a diagram of how to remove the handle?
Do Not Cut the hose! It has wiring inside to control the vac and power head. This is a swivel handled hose with both low and high voltage contacts in it. The same wiring which gives the hose its ribbing, is conducting current for two applic ... Electrolux Centralux Vacuum
I want to remove the hose from the handle of the vacuum? I already removed the plastic clip. I thought that would free the hose, but it did not. Any ideas?
There are two discs on top on the dandel that cover the screws. You need to remove the two screws and the you can take the handle off the hose.\015\012\015\012Bob\015\012 ... Electrolux Centralux Vacuum
Dust....dust....dust Hello, I recently bought a house with an older Electrolux Central Vac system. I'm unfamiliar with them, so I'm not sure how to deal with this: I cleaned up some mortar dust with it, and noticed not too long after that when I went into the garage, there was a fog of dust. The hose from the unit is venting into the garage. Is this normal? I have since used it for everyday household cleaning and each time I go back to the garage to a cloud of dust. Is there anything I can
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=113662&thid=662824\015\012Dust....dust....dust\015\012Posted by Kitkatman on Jun 11, 2008\015\012Hello,I re ... Electrolux Central Vacuum
Clogged hose... I have a clog in my hose, probably a sock, I have pushed it through to the hard plastic handle end of the hose, help! can the plastic handle wand be disconnected from the hose to remove the clog??? Thank you
Hi!\015\012 \015\012Low suction, poor pickup, or no suction may be due to a clog in the vacuum cleaner. If you notice a change in the sound of the motor or a reduction in the spinning action in the Dirt Con ... Bissell 6594 PowerForce Bagless Upright Vacuum